Intellinet 524803 User Manual
  1. Manuals
  2. Brands
  3. Intellinet Manuals
  4. Wireless Router
  5. 524803
  6. User manual

Intellinet 524803 User Manual

Wireless 150n portable 3g router
Hide thumbs Also See for 524803:
Table of Contents

Advertisement

Quick Links

Download this manual
WIRELESS
150N
PORTABLE
3G ROUTER
USER
MANUAL
MODEL
524803
INT-524803-UM-1009-02

Advertisement

Table of Contents
loading

Related Manuals for Intellinet 524803

Summary of Contents for Intellinet 524803

  • Page 1 WIRELESS 150N PORTABLE 3G ROUTER USER MANUAL MODEL 524803 INT-524803-UM-1009-02...

  • Page 2: Federal Communications Commission

    Federal Communications Commission Interference Statement FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
  • Page 3 cause harmful interference; and (2) This device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the authority to operate the equipment. Federal Communications Commission (FCC) Radiation Exposure Statement This equipment complies with FCC radiation exposure set forth for...
  • Page 4 R&TTE Compliance Statement This equipment complies with all the requirements of Directive 1999/5/EC of the European Parliament and the Council of March 9, 1999, on radio equipment and telecommunication terminal equipment and the mutual recognition of their conformity (R&TTE). The R&TTE Directive repeals and replaces in the directive 98/13/EEC (Telecommunications Terminal Equipment and Satellite Earth Station Equipment) as of April 8, 2000.

  • Page 5: Table Of Contents

    Table of Contents CHAPTER I: PRODUCT INFORMATION 1-1 Introduction ................1 1-2 Safety Information..............2 1-3 System Requirements............3 1-4 Package Contents..............3 1-5 Connections and Indicators ...........4 1-6 Charging the Battery ..............6 CHAPTER II: SYSTEM AND NETWORK SETUP 2-1 Network Connections.............8 2-2 Connecting to the Router via Web Browser......8 2-2-1 Windows 95/98/Me IP Address Setup ........9 2-2-2 Windows 2000 IP Address Setup ........11 2-2-3 Windows XP IP Address Setup.........13...
  • Page 6 2-5-6 Setup Procedure for L2TP ..........51 2-5-7 Setup Procedure for Telstra Big Pond ......53 2-5-8 Setup Procedure for DNS ..........54 2-5-9 Setup Procedure for DDNS ..........56 2-6 Wired LAN Configurations ...........58 2-6-1 LAN IP ................59 2-6-2 DHCP Server ..............60 2-6-3 Static DHCP Leases Table ..........61 2-7 Wireless LAN Configurations ..........63 2-7-1 Basic Wireless Settings ............64 2-7-2 Advanced Wireless Settings ..........67...
  • Page 7 3-3-4 Demilitarized Zone (DMZ)..........108 3-4 FailOver ................110 3-5 System Status..............112 3-5-1 System Information and Firmware Version.....112 3-5-2 Internet Connection Status ..........113 3-5-3 Device Status..............113 3-5-4 System Log..............114 3-5-5 Security Log..............115 3-5-6 Active DHCP Client List ..........116 3-5-7 Statistics .................116 3-5-8 Modem Info..............117 3-6 Configuration Backup and Restore ........117 3-7 Firmware Upgrade .............118 3-8 System Reset..............119...

  • Page 8: Chapter I: Product Information

    1-1 Introduction and Safety Information Thank you for purchasing this INTELLINET NETWORK SOLUTIONS Wireless 150N Portable 3G Router, Model 524803. This high-speed wireless 3G broadband router supports both UMTS/ HSDPA and EVDO networks. When connecting a 3G / 3.5G USB modem* to the router, all network (wired/wireless) users can share the 3G / 3.5G Internet connection.

  • Page 9: Safety Information

    1-2 Safety Information To maintain the safety of users and property, follow these safety instructions: 1. This device is designed for indoor use only; DO NOT place this device outdoors. 2. DO NOT put this device in or near hot or humid places, like a kitchen or bathroom.

  • Page 10: System Requirements

    1-3 System Requirements • Internet connection, provided by xDSL or cable modem or 3G / 3.5 modem. • Computer or network devices with wired or wireless network interface card. • Web browser (Firefox, Microsoft Internet Explorer 4.0 or above, Netscape Navigator 4.7 or above, Opera Web browser or Safari Web browser) •...

  • Page 11: Connections And Indicators

    1-5 Connections and Indicators ETHERNET LED Name Light Status Description Green On Router is switched on and correctly powered or the battery is charged completely. Orange On The battery is charging. Orange Battery power is not enough, only 30 PWR/CHG Flashing minutes remains.
  • Page 12 Wireless network is switched off. WLAN Flashing Wireless LAN activity (transferring or receiving data). Wireless WPS function is enabled. Wireless WPS function is not enabled or the connection is successfully. ETHERNET port is connected. ETHERNET port is not connected. ETHERNET Flashing ETHERNET activity (transferring or receiving data).

  • Page 13: Charging The Battery

    Start WPS function or reset the router to factory default settings (clear all settings). Press this button and hold for over 10 seconds to restore all settings to factory defaults, or press this button for less than 5 seconds to start WPS function.
  • Page 14 3. On the left side panel, set the On/Off switch to On. CAUTION: Always switch the router off before removing the battery, and only use the battery and power adapter or car charger included with the router, as other types could be dangerous and damage the router.

  • Page 15: Chapter Ii: System And Network Setup

    Chapter II: System and Network Setup 2-1 Network Connections If needed, visit www.intellinet-network.com for a complete list of compatible 3G USB modems. 1. Connect your 3G / 3.5G USB modem to the USB port on the top panel of the router. 2.

  • Page 16: Windows 95/98/Me Ip Address Setup

    address, or if you’re unsure, follow the instructions below to configure your computer to use a dynamic IP address: If the operating system of your computer is Windows 95/98/Me - go to section 2-2-1 Windows 2000 - go to section 2-2-2 Windows XP - go to section 2-2-3 Windows Vista...
  • Page 17 2. Select “Obtain an IP address from a DHCP server” and then click “OK.”...

  • Page 18: Windows 2000 Ip Address Setup

    2-2-2 Windows 2000 IP Address Setup 1. Click Start (at the lower-left corner of your desktop), then click Control Panel. Double-click the Network and Dial-up Connections icon; click Local Area Connection; the Local Area Connection Properties window will appear. Select “Internet Protocol (TCP/IP)”...
  • Page 19 2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically,” then click “OK.”...

  • Page 20: Windows Xp Ip Address Setup

    2-2-3 Windows XP IP Address Setup 1. Click Start (at the lower-left corner of your desktop), then click Control Panel. Double-click the Network and Internet Connections icon, click Network Connections, then double-click Local Area Connection; the Local Area Connection Status window will appear. Click “Properties.”...
  • Page 21 2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically,” then click “OK.”...

  • Page 22: Windows Vista Ip Address Setup

    2-2-4 Windows Vista IP Address Setup 1. Click Start (at the lower-left corner of your desktop), then click Control Panel. Click View Network Status and Tasks, and then click Manage Network Connections. Right-click Local Area Network, then select “Properties.” The Local Area Connection Properties window will appear.
  • Page 23 2. Select “Obtain an IP address automatically” and “Obtain DNS server address automatically,” then click “OK.”...

  • Page 24: Router Ip Address Lookup

    2-2-5 Router IP Address Lookup After the IP address setup is complete, go to Start, then Run at the bottom-lower corner of your desktop: Input “cmd,” then click “OK.”...
  • Page 25 Input “ipconfig,” then press <Enter>. Check the IP address followed by the default gateway (in this example, the IP address of the router is 192.168.2.1). NOTE: If the IP address of the default gateway is not displayed, or if the address following “IP Address”...
  • Page 26 Enter a user name and password in their respective fields (default user name is “admin”; default password is “1234”). Click “OK” band you can see the Web management interface of the router. NOTE: If you can’t see the Web management interface and you’re being prompted to input the user name and password again, it means you didn’t input the user name and password correctly: Re-enter the user name and password.

  • Page 27: Using Quick Setup

    2-3 Using Quick Setup Quick Setup lets you complete all the required settings you need in order to access the Internet very quickly. Click “Quick Setup” on the left-hand navigation panel. The following message will be displayed: 1. Set Time Zone Below are descriptions of each option: Set Time From the drop-down menu, select the...
  • Page 28 Time Server Input the IP address / host name of time server Address (2): here. Daylight If the country you live in uses Daylight Saving, Savings (3): check “Enable Function” and choose the duration of Daylight Saving. After you finish the settings, click “Next” (4). NOTE: There are several time servers available on the Internet: 129.6.15.28 (time-a.nist.gov) 132.163.4.101 (time-a.timefreq.bldrdoc.gov)
  • Page 29 2. Broadband Type Choose the broadband (Internet connection) type you’re using. There are seven types of Internet connections: 3G/3.5G - go to section 2-3-1 Cable Modem - go to section 2-3-2 Fixed-IP xDSL - go to section 2-3-3 PPPoE xDSL - go to section 2-3-4 PPTP xDSL - go to section 2-3-5...
  • Page 30 NOTE: Some service providers use DHCP (Dynamic Host Configuration Protocol) to assign an IP address to you. In this case, you can choose Cable Modem as the Internet connection type even you’re using another connection type, like xDSL. Also, some cable modems use PPPoE, so you can choose PPPoE xDSL for such a connection even if you’re using a cable modem.
  • Page 31 (maximum 32 characters). SSID is used to identify your own wireless router from others when there are other wireless routers in the area. Default SSID is “INTELLINET”; it’s recommended to change the default SSID name to one that is easily recognizable, such as “my home,”...

  • Page 32: Setup Procedure For 3G/3.5G

    4. Security Settings Choose the Encryption type you’re using from the drop-down list. There are three types of Encryption: - go to section 2-7-3-2 WPA pre-shared key - go to section 2-7-3-3 WPA RADIUS - go to section 2-7-3-4 To go back to a previous step, click “Back” at the bottom of the page.
  • Page 33 Below are descriptions of each option: PIN Code (1): Enter a Pin Code for your UMTS or HSDPA or EVDO connection. This is optional, and is only required if your service provider asks you to do APN (2): Enter the APN code assigned by your Internet service provider here.

  • Page 34: Setup Procedure For Cable Modem

    2-3-2 Setup Procedure for Cable Modem Below are descriptions of each option: Host Name (1): Enter the host name of your computer This is optional, and is only required if your service provider asks you to do so. MAC Address (2): Enter the MAC address of your computer here if your service provider only permits computers with a certain MAC address to access the Internet.

  • Page 35: Setup Procedure For Fixed-Ip Xdsl

    2-3-3 Setup Procedure for Fixed-IP xDSL Below are descriptions of the options: IP address (1): Enter the IP address assigned by your service provider. Subnet Mask (2): Enter the subnet mask assigned by your service provider. DNS Address (3): Enter the IP address of the DNS server provided by your service provider.

  • Page 36: Setup Procedure For Pppoe Xdsl

    2-3-4 Setup Procedure for PPPoE xDSL Below are descriptions of each option: User Name (1): Enter the user name assigned by your Internet service provider here. Password (2): Enter the password assigned by your Internet service provider here. Service Name (3): Assign a name to this Internet service (optional).

  • Page 37: Setup Procedure For Pptp Xdsl

    When you finish the settings, click “Next” (7); to go back to a previous menu, click “Back.” MTU - If you don’t know what it is, ask your service provider for a proper value. Connection Type - There are 3 options: “Continuous” keeps the Internet connection alive (doesn’t disconnect);...
  • Page 38 WAN interface settings must be correctly set; otherwise, the Internet connection will fail even if the PPTP settings are correct. Contact your Internet service provider if you don’t know how you should fill in these fields. Next, PPTP Settings: Below are descriptions of each option: User Name (1): Enter the user name assigned by your Internet service provider here.

  • Page 39: Setup Procedure For L2Tp Xdsl

    by the BEZEQ network in Israel. Connection Type (7): Select the connection type of Internet connection you want to use (refer to the last section for detailed descriptions). Idle Time Out (8): Enter the idle time out of the Internet connection you want to use (refer to the last section for detailed descriptions).
  • Page 40 should fill in these fields. Next, L2TP Settings: Below are descriptions of each option: User Name (1): Enter the user name assigned by your Internet service provider here. Password (2): Enter the password assigned by your Internet service provider here. L2TP Gateway (3): Enter the IP address of PPTP gateway assigned by your Internet service provider here.

  • Page 41: Setup Procedure For Telstra Big Pond

    2-3-7 Setup Procedure for Telstra Big Pond This setting only works when you’re using Telstra Big Pond’s network service in Australia. User Name (1): Enter the user name assigned by Telstra. Password (2): Enter the password assigned by Telstra. Assign login Check this box to choose a login server by server manually yourself.
  • Page 42 Click “Apply” to prepare to restart the router, and you’ll see this message: Wait for about 30 seconds, then click “OK!” You’ll be back to the router management interface, and the router is ready with new settings.

  • Page 43: Basic Setup

    2-4 Basic Setup In this chapter, you’ll know how to change the time zone, password and remote management settings. Start your Web browser and log on to the router’s Web management interface, then click “General Setup” on the left (or click the “General Setup” link at the upper-right corner of the screen).

  • Page 44: Changing The Management Password

    Below are descriptions of each option: Time Zone (1): Select a time zone from the drop-down list. Time Server Enter the IP address or host name of the time Address (2): server here. Daylight Check the “Enable” box and set the Savings (3): duration of Daylight Saving.
  • Page 45 To change the password, click “System” on the left side of the Web management interface, then click “Password Settings.” The following message will be displayed on your Web browser: Below are descriptions of each option: Current Enter the current password here. Password (1): New Password (2): Enter the new password here.

  • Page 46: Remote Management

    If you see the following message, the content in the “Current Password” field is wrong. Click “OK” to go back to the previous menu, and try to enter the current password again. If the current and new passwords are correctly entered, after you click “Apply”...
  • Page 47 then click “Remote Management.” The following message will be displayed on your Web browser: Below are descriptions of each option: Host Address (1): Input the IP address of the remote host for which you want to initiate management access. Port (2): You can define the port number through which the router should expect an incoming request.
  • Page 48 NOTE: When you want to manage this router from another computer on the Internet, you need to input the IP address and port number of this router. If your Internet service provider assigns you a static IP address, it will not be a problem; but if the IP address your service provider assigns you will vary every time you establish an Internet connection, this will be a problem.

  • Page 49: Set Up The Internet Connection (Wan Setup)

    2-5 Setting Up the Internet Connection (WAN) Internet connection setup can be done by using Quick Setup as described in Section 2-3. However, you can also set up WAN connections up by using the WAN configuration menu. You can also set advanced functions like DDNS (Dynamic DNS) here. Click “WAN”...

  • Page 50: Setup Procedure For 3G/3.5G

    PPTP - go to section 2-5-5 L2TP - go to section 2-5-6 Telstra Big Pond - go to section 2-5-7 - go to section 2-5-8 DDNS - go to section 2-5-9 2-5-1 Setup Procedure for 3G/3.5G Below are descriptions of each option: PIN Code (1): Enter the Pin Code for your UMTS or HSDPA connection.
  • Page 51 Verify Password (5): Enter the password again for confirmation. Service (6): Select your card type from the drop-down menu. AT Dial Script (7): Enter the dialed number for your UMTS or HSDPA connection. The default is *99#. This field should not be altered except when required by your service provider.

  • Page 52: Setup Procedure For Dynamic Ip

    2-5-2 Setup Procedure for Dynamic IP Below are descriptions of each option: Host Name (1): Enter the host name of your computer. This is optional, and is only required if your service provider asks you to do so. MAC Address (2): Enter the MAC address of your computer if your service provider only permits computers with certain MAC addresses Internet access.

  • Page 53: Setup Procedure For Static Ip

    Click “Continue” to go back and continue with the router setup, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router is rebooting.) 2-5-3 Setup Procedure for Static IP Below are descriptions of each option: IP address (1): Enter the IP address assigned by your...

  • Page 54: Setup Procedure For Pppoe

    message will be displayed on your Web browser: Click “Continue” to go back and continue with the router setup, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router is rebooting.) If you want to reset all settings on this page back to previously saved values, click “Cancel.”...
  • Page 55 Password (2): Enter the password assigned by your Internet service provider here. Service Name (3): Enter a name for this Internet service. (This is optional.) MTU (4): Enter the MTU value of your network connection here. If you don’t know it, contact your ISP.

  • Page 56: Setup Procedure For Pptp

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router is rebooting.) If you want to reset all settings on this page back to previously saved values, click “Cancel.”...
  • Page 57 your Internet service provider if you don’t know how you should fill in these fields. Next, PPTP Settings: Below are descriptions of each option: User Name (1): Enter the user name assigned by your Internet service provider here. Password (2): Enter the password assigned by your Internet service provider here.

  • Page 58: Setup Procedure For L2Tp

    Type (7): connection you want to use. (Refer to section 2-5-3 for detailed descriptions.) Idle Time Out (8): Enter the idle time out of the Internet connection you want to use. (Refer to section 2-5-3 for detailed descriptions.) When you finish the settings, click “Apply” (9) and the following message will be displayed on your Web browser: Click “Continue”...
  • Page 59 Below are descriptions of each option: User Name (1): Enter the user name assigned by your Internet service provider here. Password (2): Enter the password assigned by your Internet service provider here. L2TP Gateway (3): Enter the IP address of the PPTP gateway assigned by your Internet service provider here.

  • Page 60: Setup Procedure For Telstra Big Pond

    If you want to reset all settings on this page back to previously saved values, click “Cancel.” 2-5-7 Setup Procedure for Telstra Big Pond These settings only work when you’re using Telstra Big Pond’s network service in Australia. User Name (1): Enter the user name assigned by Telstra.

  • Page 61: Setup Procedure For Dns

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router is rebooting.) If you want to reset all settings on this page back to previously saved values, click “Cancel.”...
  • Page 62 Below are descriptions of each option: Primary DNS (1): Enter the IP address of the DNS server provided by your service provider. Secondary DNS (2): Enter the IP address of another DNS server provided by your service provider (this is optional).

  • Page 63: Setup Procedure For Ddns

    2-5-9 Setup Procedure for DDNS DDNS (Dynamic DNS) is an IP-to-hostname mapping service for those Internet users who don’t have a static (fixed) IP address. It will be a problem if such a user wants to provide services to other users on the Internet because their IP address will vary every time they connect to the Internet, and other users will not be able to know the IP address they’re using at a certain time.
  • Page 64 Account / Enter account or e-mail of DDNS registration. E-Mail (4): Password / Key (5): Enter the DDNS service password or key. After you finish the settings, click “Apply” (6) and the following message will be displayed on your Web browser: Click “Continue”...

  • Page 65: Wired Lan Configurations

    2-6 Wired LAN Configurations Before all computers using wired Ethernet connections (i.e., those computers connect to this router’s LAN ports 1 to 4 by Ethernet cable) can communicate with each other and access the Internet, they each must have a valid IP address. There are two ways to assign IP addresses to computers: static IP address (set the IP address for every computer manually) and dynamic IP address (IP addresses of computers will be assigned by...

  • Page 66: Lan Ip

    Click LAN on the left side of the Web management interface. There are three setup groups here: “LAN IP,” “DHCP Server” and “Static DHCP Leases Table.” 2-6-1 LAN IP Below are descriptions of the options: IP address (1): Enter the IP address of this router. Subnet Mask (2): Enter the subnet mask for this network.

  • Page 67: Dhcp Server

    2-6-2 DHCP Server These settings are only available when “DHCP Server” in “LAN IP” is enabled. Below are descriptions of the options: Lease Time (1): Choose a lease time (the duration that every computer can keep a specific IP address) of every IP address assigned by this router from the drop-down menu.

  • Page 68: Static Dhcp Leases Table

    2-6-3 Static DHCP Leases Table This function allows you to assign a static IP address to a specific computer forever, so you don’t have to set the IP address for a computer, but can still enjoy the benefit of using DHCP server. A maximum of 16 static IP addresses can be assigned here.
  • Page 69 After you click “Add,” the MAC address and IP address mapping will be added to the Static DHCP Leases Table section. If you want to delete a specific item, check the “Select” box of a MAC address and IP address mapping (1), then click “Delete” (2); if you want to delete all mappings, click “Delete All”...

  • Page 70: Wireless Lan Configurations

    2-7 Wireless LAN Configurations If your computer, PDA, game console or other network device is equipped with a wireless network interface, you can use the wireless function of this router to let them connect to the Internet and share resources with other computers with a wired LAN connection.

  • Page 71: Basic Wireless Settings

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router is rebooting.) 2-7-1 Basic Wireless Settings Click Wireless on the left side of the Web management interface, then click “Basic Settings.”...
  • Page 72 2.4 GHz (B) 2.4GHz band only allows 802.11b wireless network clients to connect to this router (maximum transfer rate 11 Mbps). 2.4 GHz (N) 2.4GHz band only allows 802.11n wireless network clients to connect to this router (maximum transfer rate 150 Mbps). 2.4 GHz (B+G) 2.4GHz band only allows 802.11b and 802.11g wireless network clienst to connect...
  • Page 73 it’s recommended to change default ESSID name to one that is meaningful to you, such as “myhome,” “office_room1,” etc. Channel Number (3): Select a channel from the drop-down list. Available channel numbers are 1 to 13 for European countries; 1 to 11 for the U.S. You can choose any channel number you want to use, and almost all wireless clients can locate the channel you’re using automatically without...

  • Page 74: Advanced Wireless Settings

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router is rebooting.) 2-7-2 Advanced Wireless Settings This router provides some advanced control of wireless parameters. Click Wireless on the left side of the Web management interface, then click “Advanced Settings”...
  • Page 75 Below are descriptions of the options: Fragment Set the threshold of the wireless radio. Threshold (1): Do not modify the default value if you don’t know what it does (default value is 2346). RTS Threshold (2): Set the RTS threshold of the wireless radio. Do not modify the default value if you don’t know what it does (default value is 2347).
  • Page 76 your wireless router (set the option to “Disable”) so only those who know the ESSID of your wireless router can connect. CTS Protect (10): Enabling this setting will reduce the chance of radio signal collisions between 802.11b and 802.11g/n wireless access points. It’s recommended to set this option to “Auto”...

  • Page 77: Wireless Security

    2-7-3 Wireless Security It’s very important to set wireless security settings properly! If you don’t, hackers and malicious users can reach your network and valuable data without your consent, causing a serious security problem. Click Wireless on the left side of the Web management interface, then click “Security Settings.”...
  • Page 78 Below are descriptions of the options: Key Length (2): There are two types of WEP key length: 64-bit and 128-bit. “128-bit” is safer than “64-bit” but will reduce some data transfer performance. Key Format (3): There are two types of key format: ASCII and Hex.
  • Page 79 key here; if you enter multiple WEP keys, they should all be different. Enable 802.1x IEEE 802.1x is an authentication protocol. Authentication (9): Every user must use a valid account to log in to this wireless router before accessing the wireless LAN.

  • Page 80: Wi-Fi Protected Access (Wpa)

    After you finish the WEP settings, click “Apply” (10) and the following will be displayed on your Web browser: Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect.

  • Page 81: Wpa Radius

    Pre-shared Select the type of pre-shared key. You Key Format (3): can select Passphrase (8 or more alphanumerical characters, up to 63), or Hex (64 characters of 0-9 and a-f). Pre-shared Enter the WPA passphrase here. Key (4): It’s not recommended to use a word that can be found in a dictionary due to security reasons.
  • Page 82 Below are descriptions of the options: WPA Unicast Select a type of WPA cipher suite. Cipher Suite (2): Options are “WPA (TKIP),” “WPA2 (AES)” and “WPA2 Mixed.” You can select any one of them, but you have to make sure your wireless client supports the cipher you selected.

  • Page 83: Wireless Access Control

    2-7-4 Wireless Access Control This function will help you to prevent unauthorized users from connecting to your wireless router; only those wireless devices who have the MAC address you assigned here can gain access to your wireless router. You can use this function with other security measures described in previous section, to create a safer wireless environment.
  • Page 84 Enable Wireless To enforce MAC address filtering, check Access Control (4): “Enable Wireless Access Control.” When this item is unchecked, the router will not enforce MAC address filtering of wireless clients. MAC Address (5): Input the MAC address of your wireless devices here.

  • Page 85: Wi-Fi Protected Setup (Wps)

    2-7-5 Wi-Fi Protected Setup (WPS) Wi-Fi Protected Setup (WPS) is the simplest way to build a connection between wireless network clients and this wireless router. You don’t have to select an encryption mode or input a long encryption passphrase every time you need to set up a wireless client: You only need to press a button on the wireless client and this wireless router, and the WPS will do the rest for you.
  • Page 86 Below are descriptions of the options: Enable WPS (1): Check this box to enable WPS function; uncheck it to disable WPS. Wi-Fi Protected WPS-related system information will be Setup Info (2): displayed here: WPS Status: If the wireless security (encryption) function of this wireless router is properly set, you’ll see “Configured.”...

  • Page 87: Security Tips For Wireless Network

    Configure by Click “Start PBC" to start Push Button-style Push Button (4): WPS setup procedure. This wireless router will wait for WPS requests from wireless clients for 2 minutes. The WLAN LED on the wireless router will be lit for 2 minutes when this wireless router is waiting for incoming WPS requests.

  • Page 88: Chapter Iii Advanced Functions

    Chapter III Advanced Functions 3-1 Quality of Service (QoS) Quality of service provides an efficient way for computers on the network to share the Internet bandwidth with a promised quality of Internet service. Without QoS, all computers and devices on the network will compete with each other to get Internet bandwidth, and some applications which require guaranteed bandwidth (like video streaming and network telephone) will be affected, possibly...

  • Page 89: Add A New Qos Rule

    Enable QoS (1): Check this box to enable the QoS function; de-select this box if you don’t want to enforce QoS bandwidth limitations. Total Download You can set the limit of total download Bandwidth (2): bandwidth in kbits. To disable the download bandwidth limitation, enter “0”...

  • Page 90: Add A New Qos Rule

    selected by clicking this button. Move Down (10): You can lower the priority of the QoS rule you selected by clicking this button. After you finish the settings, click “Apply” (11) and the following message will be displayed on your Web browser: Click “Continue”...
  • Page 91 Below are descriptions of the options: Rule Name (a): Enter a name for this QoS rule (up to 15 alphanumerical characters). Bandwidth (b): Set the bandwidth limitation of this QoS rule. You need to select the data direction of this rule (Upload of Download), and the speed of bandwidth limitation in kbps, then select the type of QoS: “Guarantee”...
  • Page 92 Remote IP Specify the remote (destination) IP address Address: (e): that will be affected by this rule. Input the starting IP address in the left field and input the end IP address in the right field to define a range of IP addresses, or just input the IP address in the left field to define a single IP address.

  • Page 93: Network Address Translation (Nat)

    3-2 Network Address Translation (NAT) Network address translations solve the problem of sharing a single IP address on multiple computers. Without NAT, all computers must be assigned a valid Internet IP address to get connected to the Internet, but Internet service providers provide only a very few IP addresses to each user.

  • Page 94: Port Forwarding

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router reboots.) 3-2-2 Port Forwarding This function allows you to redirect a single port or consecutive ports of an Internet IP address to the same port of the IP address on a local network.
  • Page 95 Below are descriptions of the options: Enable Port Check this box to enable port mapping; Forwarding (1): uncheck this box to disable port mapping. Private IP (2): Input the IP address of the computer on the local network that provides Internet service. Computer Name (3): Pull down the menu and all the computers connected to the router will be listed here.

  • Page 96: Virtual Server

    Reset (12): Unselect all mappings. After you finish the settings, click “Apply” (13) and the following message will be displayed on your Web browser: Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect.
  • Page 97 Below are descriptions of the options: Enable Virtual Check this box to enable the virtual server; Server (1): uncheck this box to disable it. Private IP (2): Input the IP address of the computer which provides Internet service. Computer Name (3): Pull down the menu and all the computers connected to the router will be listed here.
  • Page 98 Reset (9): Remove all entered values. Virtual Server All existing virtual server mappings will be Table (10): displayed here. Delete (11): Select a virtual server mapping by clicking the “Select” box of the mapping, then click “Delete Selected” to remove the mapping. If there’s no existing mapping, this button will be grayed out.

  • Page 99: Port Mapping For Special Applications

    3-2-4 Port Mapping for Special Applications Some applications require more than one connection a time; these applications won’t work with simple NAT rules. In order to make these applications work, you can use this function. Below are descriptions of the options: Enable (1): Check this box to enable special applications;...
  • Page 100 Popular This section lists the more popular applications Applications (7): that require multiple connections. Select an application from the “Popular Applications” section and click “Add” to save the setting to “Current Trigger-Port Table.” Add (8): Add the setting to the “Current Trigger-Port Table.”...

  • Page 101: Upnp Setting

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router reboots.) If you want to reset all settings on this page back to previously saved values, click “Cancel.”...

  • Page 102: Alg Settings

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router reboots.) If you want to reset all settings on this page back to previously saved values, click “Cancel.”...
  • Page 103 There are many applications listed here. Check the box of the special support for applications you need, then click “Apply.” The following message will be displayed on your Web browser: Click “Continue” to go back and continue with the router setup procedure, or click “Apply”...

  • Page 104: Firewall

    3-3 Firewall In addition to NAT, this router provides firewall functions to block malicious intruders from accessing your computers on your local network. These functions include inbound attack prevention and blocking of outbound traffic, such as blocking URLs that have pre-defined keywords.

  • Page 105: Access Control

    3-3-1 Access Control This function allows or denies computers with specific MAC addresses access to the network; it can also allow or deny computers with a specific IP address, protocol or port. Click “Firewall” on the left side of the Web management interface, then click “Access Control.”...
  • Page 106 “aa:bb:cc:dd:ee:ff,” just input “aabbccddeeff.” Computer Name (3): Pull down the menu and all the computers connected to the router will be listed here. You can select the computer name without checking the IP address of the computer. Comment (4): You can input any text here as a comment about this MAC address, such as “ROOM 2A Computer.”...
  • Page 107 the network; if you select “Allow,” only IP addresses listed in the filtering table will be able to connect to the network, and all other network devices will be rejected. IP Filtering All existing IP addresses in the filtering table will Table (12): be listed here.

  • Page 108: Add Pc

    3-3-1-1 Add PC After this button is clicked, the following message will be displayed on your Web browser: Below are descriptions of the options: Client PC Enter any text to describe this IP address. (Up Description (a): to 16 alphanumerical characters.)

  • Page 109: Url Blocking

    Client PC IP Input the starting IP address in the left address (b): field and input the end IP address in the right field to define a range of IP addresses, or just input the IP address in the left field to define a single IP address.
  • Page 110 Below are descriptions of the options: Enable URL Check this box to enforce URL Blocking; Blocking (1): uncheck it to disable URL Blocking. URL/Keyword (2): Input the URL (host name or IP address of the Web site, like http://www.blocked-site.com or http://11.22.33.44), or the keyword that is contained in the URL (like pornography, cartoon, stock or anything).

  • Page 111: Dos Attack Prevention

    Delete All (7): If you want to delete all URL/Keyword entries listed here, click “Delete All.” Reset (8): You can also click “Reset” to unselect all URL/Keyword entries. After you finish the settings, click “Apply” (9) and the following message will be displayed on your Web browser: Click “Continue”...
  • Page 112 Below are descriptions of the options: Ping of Death (1): Ping of Death is a special packet, and it will cause certain computers to stop responding. Check this box and the router will filter this kind of packet out. Discard Ping Ping is a common and useful tool for learning From WAN (2): the connection status of a specified remote...

  • Page 113: Dos - Advanced Settings

    server become unusable. Check this box and the router will filter this kind of traffic out. Advanced Click this button and you can set advanced Settings (5): settings of the DoS prevention method listed above (see section 3-3-3-1 DoS – Advanced Settings below).
  • Page 114 Below are descriptions of the options: Ping of Death (a): Set the threshold for when this DoS prevention mechanism will be activated. Check the box of Ping of Death, and input the frequency of the threshold (how many packets per second, minute or hour).

  • Page 115: Demilitarized Zone (Dmz)

    Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router reboots.) If you want to reset all settings on this page back to previously saved values, click “Cancel.”...
  • Page 116 Below are descriptions of the options: Enable DMZ (1): Check this box to enable the DMZ function; uncheck this box to disable the DMZ function. Public IP You can select “Dynamic IP” or “Static IP” here. address (2): If you select “Dynamic IP,” you need to select an Internet connection session from the drop-down menu;...

  • Page 117: Failover

    Reset (10): You can also click “Reset” to unselect entries. After you finish the settings, click “Apply” (11) and the following message will be displayed on your Web browser: Click “Continue” to go back and continue with the router setup procedure, or click “Apply”...
  • Page 118 Below are descriptions of the options: WAN FailOver (1): Check this box to enable the function. WAN Priority (2): Select the WAN connection priority from the drop-down menu. Idle Timeout Input the idle time for detecting the Internet Detect (3): connection.

  • Page 119: System Status

    message will be displayed on your Web browser: Click “Continue” to go back and continue with the router setup procedure, or click “Apply” to reboot the router so the settings will take effect. (Wait for about 30 seconds while the router reboots.) 3-5 System Status The functions described here will provide you with system-related information.

  • Page 120: Internet Connection Status

    3-5-2 Internet Connection Status Click “Internet Connection” on the left side of the Web management interface, and the following message will be displayed on your Web browser: This information will vary depending on the connection status. 3-5-3 Device Status Click “Device Status” on the left side of the Web management interface, and the following message will be displayed on your Web browser:...

  • Page 121: System Log

    This information will vary depending on the device status. 3-5-4 System Log All important system events are logged. You can use this function to check the event log of your router. Click “System Log” on the left side of the Web management interface, and the following message will be displayed on your Web browser: Below are descriptions of the options:...

  • Page 122: Security Log

    Clear (2): Delete all event logs displayed here. Refresh (3): Refresh the event log display. 3-5-5 Security Log All information about network and system security is kept here, and you can use this function to check the security event log of your router.

  • Page 123: Active Dhcp Client List

    3-5-6 Active DHCP Client List If you’re using the DHCP server function of this router, you can use this function to check all active DHCP leases issued by this router. Click “Active DHCP Client” on the left side of the Web management interface, and the following message will be displayed on your Web browser: All information about active DHCP leases issued by this router will...

  • Page 124: Modem Info

    3-5-8 Modem Info Use this function to check the information of the 3G modem card. Click “Modem” Info on the left side of the Web management interface, and the following message will be displayed on your Web browser: 3-6 Configuration Backup and Restore You can back up all configurations of this router to a file so you can make several copies of the router configuration for security reasons.

  • Page 125: Firmware Upgrade

    filename is “config.bin”).You can save it as another filename for different versions and keep it in a safe place. Restore Click “Browse…” to pick a previously saved Settings (2): configuration file from your computer, then click “Upload” to transfer the file to the router. After the configuration is uploaded, the router’s configuration will be replaced by the file you just uploaded.

  • Page 126: System Reset

    Click “Next” and the following message will be displayed: Click “Browse” first and you’ll be prompted to provide the filename of the firmware upgrade file. Download the latest firmware file from www.intellinet-network.com and use it to upgrade your router. After a firmware upgrade file is selected, click “Apply” and the router will start the firmware upgrade procedure automatically.
  • Page 127 Click “Apply” to reset your router. It will be available again after a few minutes.

  • Page 128: Chapter Iv: Appendix

    Chapter IV: Appendix 4-1 Specifications Standards • IEEE 802.1d (Spanning Tree Protocol) • IEEE 802.11b (11 Mbps Wireless LAN) • IEEE 802.11g (54 Mbps Wireless LAN) • IEEE 802.11n Draft 2.0 (300 Mbps Wireless LAN) • IEEE 802.3 (10Base-T Ethernet) •...
  • Page 129 - NTP - NAT - DHCP - DNS • NAT: - Virtual server - Port forwarding - Special applications (port trigger) • Firewall: - Access control based on MAC address - URL filter - DMZ (demilitarized zone) • Supports UPnP (Universal Plug and Play) •...
  • Page 130 - OFDM: 14 dBm +/- 1 dBm (54 Mbps, 32 mW max.) - CCK: 17 dBm +/- 1 dBm (11 Mbps, 63 mW max.) • Receiver sensitivity: - 11n (150 Mbps) MCS0-7: 20 MHz: -72 dBm; 40 MHz: -70 dBm - 11g (54 Mbps) OFDM: -76 dBm - 11b (11 Mbps) CCK: -91 dBm •...
  • Page 131 • Li-ion battery • Ethernet Cat5 RJ45 cable: 1.0 m (3 ft.) • USB extension cable: 1.0 m (3 ft.) • Car charger • Carrying case...

  • Page 132: Troubleshooting

    4-2 Troubleshooting If you find the router is working improperly or has stopped responding, see if a possible solution appears in this section before you contact your dealer of purchase for help. Scenario Solution Router is not a. Check the router’s power cord and responding when I network cable connections.
  • Page 133 connected to the Internet with your computer directly attached to the device provided by your Internet service provider. d. Check the PPPoE / L2TP / PPTP user ID and password again. e. Call your Internet service provider and check if there’s something wrong with their service.
  • Page 134 d. If this never happened before, call your Internet service provider to see if there is something wrong with their network. I can’t log on to the a. Make sure you’re connecting to the Web management correct IP address of the router. interface;...

  • Page 135: Glossary

    4-3 Glossary Default Gateway (Router): Every non-router IP device needs to configure a default gateway’s IP address. When the device sends out an IP packet, if the destination is not on the same network, the device has to send the packet to its default gateway, which will then send it out toward the destination.
  • Page 136 computer host in an IP network. Example: 192.168.2.1. It consists of 2 portions: the IP network address, and the host identifier. The IP address is a 32-bit binary pattern, which can be represented as four cascaded decimal numbers separated by “.”: aaa.aaa.aaa.aaa, where each “aaa”...
  • Page 137 MAC Address: MAC stands for Media Access Control. A MAC address is the hardware address of a device connected to a network. The MAC address is a unique identifier for a device with an Ethernet interface. It is comprised of two parts: 3 bytes of data that corresponds to the Manufacturer ID (unique for each manufacturer), plus 3 bytes that are often used as the product’s serial number.
  • Page 138 transmitting information over Ethernet between different manufacturers. Protocol: A protocol is a set of rules for interaction agreed upon between multiple parties so that when they interface with each other based on such a protocol, the interpretation of their behavior is well defined and can be made objectively, without confusion or misunderstanding.

Table of Contents