Aspect Ratio; Isf Calibration - Runco RS-1100 CineWide Owner's Operating Manual

Brightness
Contrast
Color
Video
Tint
S-Video
Sharpness
Component1
Filter
Component2
Color Temperature
RGB-HD
ICC Selection
HDMI
Store Image Settings
Restore Image
Settings
Anamorphic (16:9)
Standard (4:3)
Letterbox
Virtual Wide

Aspect Ratio

Cinema
Virtual Cinema
Language
Picture Orientation
Installation
Keystone Adjust
Background Color
RS-232 Baud Rate
Blue Image
Reset Image Settings
Sleep Timer
Lamp Hours
OSD Timer
OSD Position
PC & HD Adjust (480p
and higher-res.
Option
signals only)
PIP/PBP Set Up
(not available when
used with the SDC-1)
DNR
Figure 4-1. RS-1100 OSD Menu Structure
Runco RS-1100 Series Owner's Operating Manual
Set Up
0 ... 60
0 ... 32
0 ... 64
0 ... 30
-14 ... 0 ... +25
0, 1, 2 or 3
5400 K, 6500 K, 8500 K,
Custom 1 or Custom 2
Standard, NTSC, HDTV or
PAL
Memory 1
Memory 1, ISF Night or
ISF Day
(available only on RS-1100
projectors equipped with
the CineWide option)
English, French, Spanish,
German or Italian
Floor Front, Floor Rear,
Ceiling Front or Ceiling
Rear
ISF
-14, -13 ... 0 ... +13, +14
Blue or White Calibration
9600, 38400 or 115200
On / Off
Yes / No
0, 10, 20, 30 ... 180 min.
(read only)
0, 3, 6, 9 ... 60 sec.
Horizontal
Vertical
Auto
Frequency 0, +1, +2, +3 ... +17
Phase 0, +1, +2, +3 ... +31
H. Position -30, -29 ... 0 ... +29, +30
V. Position -28, -27 ... 0 ... +29, +30
PIP/PBP Enable On / Off
PIP Off
PIP Set Up Graphic in Video
Video in Graphic
PBP Off
PBP Set Up Graphic by Video
Video by Graphic
0, +1, +2, ... +15
White Balance
Gamma Selection
SD Enhance
RVR Adjust
HDTV Adj.
SDTV Adj.
Image Over Scan
Image Shift
Amplitude Adjust
Horizontal Masking
Video Black Level
Lamp Power
Remote Control
Reset Lamp Timer
Fan Control
Screen Trigger Mode
Return to User OSD
Reset Picture Adjust
Picture Adjust
White Balance
Gamma Selection
Blue Image
ICC Adjust
Store Settings
Splash Screen Timer
ISF Enable
Return to User OSD
45
Gamma
Gain Red / Green / Blue
Offset
Store Custom 1
Store Custom 2
2.8, 2.5, 2.2, 1.0,
RUNCO Enhance 1,
RUNCO Enhance 2 or
ISF Day
H Enhance
V Enhance
Chroma Enhance
0, +1, +2, +3 ... +127
H Threshold
V Threshold
Chroma Threshold
0, 1, 2 ... 19
Analog RGBHV (refer to page 57)
Analog YPbPr (refer to page 57)
Signal Fine Tune (refer to page 58)
(refer to page 59)
Total 0, +1, +2, +3 ... +15
Horizontal
Vertical
Horizontal
-20, -19, ... 0 ... +19, +20
Vertical
Horizontal -60, -59 ... 0 ... +59, +60
Vertical -20, -19, ... 0 ... +19, +20
0, +1, +2, ... +100 (CineWide versions only)
0 IRE or 7.5 IRE
250W or 200W
Primary
Secondary
Yes / No
Auto Normal,
Mode
Auto Hi. Altitude or Manual
Speed (Manual Mode)
Normal or AutoScope (CineWide versions only)
Yes / No
Brightness, Contrast,
(see above)
Color etc.
Gamma, Gain, Offset etc. (see above)
2.8, 2.5, 2.2, 1.0,
RUNCO Enhance 1,
RUNCO Enhance 2 or
ISF Day
On / Off
R / G / B / Y / C / M
NTSC / HDTV / PAL
Intensity / Sat. / Hue
Memory 1, ISF Night or
ISF Day
+5, +6, +7 ... +60 sec.
On / Off
Operation