HP MPX200 User Manual page 159

Enter a new value or simply press the ENTER key to accept the current value.
If you wish to terminate this process before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE ports.
Configuring FCIP Route:
-----------------------
FCIP Interfaces FC & GE (0=Enable, 1=Disable) [Enabled
FC Port (1=FC1 2=FC2)
GE Port (1=FC1 2=GE2 3=10GE1 4=10GE2)
IP Address (IPv4 or IPv6; 0=IPv6 Link Local)
Subnet Mask
Gateway IP Address
Remote IP Address
MTU Size (0=Normal, 1=Jumbo, 2=Other)
TCP Window Size (0=32KB, 1=64KB, 2=128KB,
3=256KB, 4=512KB, 5=1MB,
6=2MB, 7=4MB, 8=8MB, 9=16MB) [4MB
TCP Port No. (Min=1024, Max=65535)
GE Port Speed (0=Auto, 1=100Mb, 2=1Gb)
Bandwidth, Mbit/sec (Min=1, Max=1000)
VLAN (0=Enable, 1=Disable)
FCIP SW Compression(0=Enable,1=Disable,2=Auto)[Disabled
All attribute values for FCIP Route 1 will now be saved.
MPX200 <1> (admin) #>
Example 2:
MPX200 <1> (admin) #> fciproute mod
A list of attributes with formatting and current values will follow.
Enter a new value or simply press the ENTER key to accept the current value.
If you wish to terminate this process before reaching the end of the list
press 'q' or 'Q' and the ENTER key to do so.
WARNING:
The following command might cause a loss of connections to both GE ports.
Route FC Port ID
----- ----------
1 FC1
2 FC2
Please select a FCIP route from the list above ('q' to quit): 1
Configuring FCIP Route:
-----------------------
FCIP Interfaces FC & GE (0=Enable, 1=Disable)
IP Address (IPv4 or IPv6; 0=IPv6 Link Local)
Subnet Mask
Gateway IP Address
Remote IP Address
MTU Size (0=Normal, 1=Jumbo, 2=Other)
TCP Window Size (0=32KB, 1=64KB, 2=128KB,
3=256KB, 4=512KB, 5=1MB,
6=2MB, 7=4MB, 8=8MB, 9=16MB)
TCP Port No. (Min=1024, Max=65535)
GE Port Speed (0=Auto, 1=100Mb, 2=1Gb)
Bandwidth, Mbit/sec (Min=1, Max=1000)
VLAN (0=Enable, 1=Disable)
FCIP SW Compression(0=Enable,1=Disable,2=Auto)
Do you want to save/discard changes? (0=Save, 1=Discard)
All attribute values for FCIP Route 1 will now be saved.
GE Port ID
----------
GE1
GE2
]
[ ] 1
[ ] 1
[0.0.0.0 ] 66.66.1.94
[0.0.0.0 ] 255.255.255.0
[0.0.0.0 ]
[0.0.0.0 ] 66.66.1.124
[Normal ]
] 5
[3225 ]
[Auto ]
[1000 ] 150
[Disabled ]
] 2
[Enabled
[66.66.1.94
[255.255.255.0
[0.0.0.0
[66.66.1.124
[Normal
[1MB
[3225
[Auto
[150
[Disabled
[Auto
[Save
]
]
]
]
]
]
] 4
]
]
] 100
]
]
]
Commands 159