PART 1 • English TABLE OF CONTENTS 1.0 INTRODUCTION 1.1 Safety Instructions 1.2 Storage 1.3 Equipment Set-up 1.4 Features & Accessories 2.0 YOUR RECEIVER 2.1 Front Panel 2.2 Rear Panel 2.2 Remote Control Unit 3.0 CONNECTIONS 3.1 Connecting to Terrestrial antenna 3.2 Connecting to TV &...
Attachments — For your safety, and to avoid damaging the controls could damage the product and require extensive product, use only accessories recommended by STRONG. repair work by a qualified technician. Water and Moisture — Never use this product around water (near 4.
PART 1 • English 1.2 Storage Your receiver and its accessories are stored and delivered in a packaging designed to protect against electric shocks and moisture. When unpacking it, make sure that all the parts are included and keep the packaging away from children.
PART 1 • English Aspect ratio adjustment 4:3, 16:9, Pan & Scan, Letterbox Software Update via USB 2.0 port and RS-232 Digital sound through optical and coaxial output (S/PDIF) Fully DVB compliant, supports MPEG-2, MPEG-4 and H.264. Multiple Video Outputs: HDMI, Component(Y, Pb, Pr), SCART (RGB, CVBS), Video RCA. Accessories 1 x User Manual 1 x Remote control unit...
PART 1 • English 2.2 Rear Panel 1. ANT IN To connect the antenna cable to this connector. 2. TO TV Gives you the possibility to connect an extra terrestrial receiver. 3. TV SCART Connector Use this connector to connect your receiver with your TV set using a SCART cable. 4.
PART 1 • English 2.2 Remote Control Unit 1. MUTE Enables or disables the audio. 2. POWER Switches the receiver between operation and standby mode. 3. RCL Selects the previously viewed channel. 4. HDMI Changes the resolutions of video (Switch HD type) 5.
Page 8
PART 1 • English 20. CH-/CH+ Changes channels up or down on normal mode. Moves up a page in the channel list.(Selects zoom In/out) Moves down a page in the channel list. 23. STOP Stops recording, timeshift or playback. 24. PAUSE Timeshift deactivated: Pauses the playing picture or go again to normal mode.
PART 1 • English 3.0 CONNECTIONS 3.1 Connecting to Terrestrial antenna To receive the broadcast signal, the terrestrial antenna cable should be connected to the ANT IN connector at the back of the receiver Fig. 3 3.2 Connecting to TV & VCR Connecting by HDMI cable To fully enjoy your HDTV channels it is advisable to use HDMI or Component video outputs of your receiver.
Connect the RS-232 connector on the back of your receiver to the Serial port of your computer using a serial cable. Instructions how to download software can be found on our website www.strong.tv (support > download). However, this receiver can download new system software from USB stick.
Timeshift to OFF or ON as desired. IMPORTANT: During formatting all data on the hard disk will be deleted and get permanently lost. STRONG cannot be granted for any loss or damage of data, if you format the hard disk.
If your home country/broadcaster supports LCN (Logical Channel Numbering), then please adjust channel numbering mode to "Operator defined" if you are not sure about this ask your local STRONG dealer. If the LCN is not supported then please select "Appearing order". 5.0 MAIN MENU All the important settings and features of your receiver can be operated in Main Menu.
Page 13
PART 1 • English First FTA Free-To-Air channels will be placed at the beginning of the list, Scrambled channels at the end. First scrambled Scrambled channels will be placed at the beginning of the list, Free-To-Air channels at the end. If you want to store new order of channels press YELLOW (Save) or BLUE (Save &...
PART 1 • English button again. Channel(s) will be deleted after you press BLUE button. Be aware: after pressing BLUE button channel(s) will be deleted from all channel lists. To cancel delete operation you can press EXIT button. Message “Do you want to save?” will appear on screen. Press EXIT to cancel or OK to confirm. 5.2 Terrestrial Search The Terrestrial Search menu contains following sub-menus: ”Channel Setup”...
Page 15
PART 1 • English Power On Channel Use pqtu buttons to select the item. If your choice is Fixed channel: press OK button to display a channel list, select a channel and confirm selection with OK button. Your receiver will always start with defined channel.
PART 1 • English Starting Time You can set the starting date or days of the week for the timer action. Use Numeric buttons to enter the starting time of the timer action. Duration Use Numeric buttons to enter the duration of channel view when the Timer mode is set to Time Interval. 5.5 Application This menu will help you to use USB, Calendar, Tetris (Game) and CAS- only use for Conax Smart card.
PART 1 • English 5.5.3 Tetris Use pq buttons to move to Tetris and press OK button. Before starting a game, you will be prompt to select level. Press numeric button to select a level which you want (1~15) and press OK. Move block to left or right.
PART 1 • English In channel list: Use pq buttons to choose the channel. Use tu to switch between channel list and program schedule. In program schedule list: Use pq buttons to choose program. Use RED/GREEN buttons to select previous/next day of schedule. Use tu to switch between channel list and program schedule.
USB device. STRONG cannot guarantee for USB devices used. Especially when Timeshift is activated at channels with high data rate, STRONG cannot guarantee an accurate Playback of the Timeshift file. Any risk of the PDR function usage shall not be passed to STRONG! 6.4.1 Record...
PART 1 • English 6.4.2 Play Press u (PLAY) button in TV mode and the Recording File List will appear on screen. Select with the pq buttons the file you want to watch and start playback by pressing OK. You can activate Fast Forward or Fast Rewind during playback by pressing the button.
PART 1 • English Symptom Cause Remedy No picture The receiver can’t receive the Check the antenna cable, replace the signal cable, or connect the cable to the receiver tightly. Incorrect values of channel Set the values channel parameters parameters. correctly in installation menu.