G Transparency Film With Insert Sheets; Transparency Film With Insert Sheets - Sharp AR-C170M Operation Manual

SPECIAL MODES

Transparency film with insert sheets

When copying onto transparency film, blank insert sheets can be placed between transparent sheets.
Example: Inserting insert sheets between transparencies
Originals (1-sided)
4
3
2
1
Originals (2-sided)
3
1
For two-sided originals,
this is only possible when
using a reversing single
pass feeder.
Before performing the following procedure, touch the [OUTPUT] key in the main screen of Copy mode to display the
OUTPUT settings screen (page 5-5), and then touch the [LEFT TRAY] key* to set the output tray to the left tray*.
* If the optional saddle stitch finisher is installed, touch the [FINISHER TRAY] key to set the output tray to the finisher tray.
Touch the [TRANSPARENCY INSERTS]
1
key on the SPECIAL MODES screen.
COPY
TRANSPARENCY
INSERTS
2 Touch the [OK] key on the SPECIAL
MODES screen.
Return to the main screen of copy mode.
Load transparency film into the bypass
3
tray.
Touch the [PAPER SELECT] key and
4
select the transparency film loaded in the
bypass tray.
A4
AUTO
EXPOSURE
PLAIN
HEAVY PAPER
PAPER SELECT
TRANSPARENCY
100
%
COPY RATIO
ENVELOPE
6-8
4
3
2
1
Insert sheets
During colour copying,
output takes place in
reverse order.
The [TRANSPARENCY
INSERTS] key is
highlighted to indicate
that the function is turned
on, and the transparency
inserts icon ( , etc.)
appears in the upper left
of the screen.
Remove any paper
already in the bypass
tray before loading the
transparency film. (To
load paper in the bypass
tray, see pages 2-4 and
2-5.)
Touch the
[TRANSPARENCY] key.
GInsert sheets cannot be copied on in any mode.
GThis mode can be selected only in the 1-sided to 1-
sided and 2-sided to 1-sided modes.
GA multiple number of copies cannot be selected in
this mode.
GTransparency film must be fed from the bypass tray.
GInsert sheets must be the same size (A4 or A4R (8-
1/2" x 11" or 8-1/2" x 11"R)) as the transparency film.
GFor best results, use SHARP recommended
transparency film.
GWhen using the "transparency film with insert sheets"
function for colour copying, load the original pages in
reverse order to have the output produced in forward
order.
Touch the [SPEED MODE] key or the [QUALITY
5
MODE] key for the transparency film.
PLEASE SELECT TRANSPARENCY MODE.
OK
SPEED MODE
QUALITY MODE
BASIC SETTING
EXTRA SIZE
6 Touch the [PAPER SELECT] key again and
select the paper (A4 (8-1/2" x 11") or A4R (8-
1/2" x 11"R) size) to be used for the inserts.
READY TO COPY.
1. A4 PLAIN
2. B4 RECYCLED
3. A3 COLOUR
4. A4R PLAIN
About the steps that follow
If a reversing single pass feeder is being used,
see pages 5-2 and 5-3. If the document glass is
being used, see pages 5-7 and 5-8.
To cancel the TRANSPARENCY INSERTS function,
touch the [TRANSPARENCY INSERTS] key again
on the SPECIAL MODES screen.
NOTE
When the copy job is finished, remove any
transparencies that remain in the bypass tray.
SPEED MODE is for fast
printing.
QUALITY MODE is for a
high quality image.
After touching either key
followed by the [OK] key,
you will return to the main
screen of copy mode.
0
INTERRUPT
A4
AUTO
EXPOSURE
PLAIN
HEAVY PAPER
PAPER SELECT
TRANSPARENCY
100
%
COPY RATIO
ENVELOPE