Page 2: Copyright Information
Copyright Information Sharp Electronics Corporation and its suppliers. Copyright © 2005 Document Information Sharp AR-C360P User’s Guide P/N 59379701, Revision 1.0 September, 2005 Disclaimer Every effort has been made to ensure that the information in this document is complete, accurate, and up-to-date. The manufacturer assumes no responsibility for the results of errors beyond its control.
Page 3: Table Of Contents
Turning Off ......38 Turning On ......39 Sharp AR-C360P User’s Guide Contents > 3...
Page 4 Staple jams – Finisher (optional accessory) ..93 Check Finisher, Staple Jam ....93 Sharp AR-C360P User’s Guide Contents > 4...
Page 5 Index........120 Sharp AR-C360P User’s Guide Contents > 5...
Page 6: Notes, Cautions And Warnings
A caution provides additional information which, if ignored, may result in equipment malfunction or damage. A warning provides additional information which, if ignored, may result in a risk of personal injury. Notes, cautions and warnings! > 6 CAUTION! WARNING! Sharp AR-C360P User’s Guide...
Page 7: Introduction
Introduction Congratulations on buying an Sharp color printer. Your new printer is designed with advanced features to give you clear, vibrant color prints and crisp black and white pages at high speed on a range of print media for the office.
Page 8 > USB 2.0 and parallel (IEEE-1284) interfaces > PCL, PS emulations > EFI Fiery controller and software > Graphics Arts capability with full suite of EFI utilities Sharp AR-C360P User’s Guide Introduction > 8...
Page 9 > Memory Expansion DIMM > Finisher for stapling or saddle stitching printer output > Punch unit (to extend Finisher functionality) > EFI Color Profiler Kit Sharp AR-C360P User’s Guide Introduction > 9...
Page 10: About This Guide
This is an electronic document stored on the Documentation > EFI Fiery documentation suite These are electronic documents stored on the EFI Utilities CD. > Installation Guides: accompany consumable items and optional accessories to describe how to install them Sharp AR-C360P User’s Guide Introduction > 10...
Page 11: Online Usage
Printing pages The whole manual, individual pages, or sections may be printed. The procedure is: From the toolbar, select [File], then [Print] (or press the Ctrl + P keys). Sharp AR-C360P User’s Guide Introduction > 11 “Contents” “Contents” on...
Page 12 [All pages], (1), for the entire manual. [Current page], (2), for the page at which you are looking. [Pages from] and [to], (3), for the range of pages you specify by entering their page numbers. Click on [OK]. Sharp AR-C360P User’s Guide Introduction > 12...
Page 13: Printer And Paper Overview
To close the top cover, push gently (1) until the cover stops midway and then push harder (2) to close the cover completely. Ensure that the cover is securely closed. Sharp AR-C360P User’s Guide Printer and paper overview > 13...
Page 14: Identifying Major Components
Paper holding arm Top cover (face-down stacker) MP Tray (multi-purpose tray) Tray 1 side cover Paper size label Paper gauge Tray 1 (paper tray) Control panel Top cover handle Sharp AR-C360P User’s Guide Printer and paper overview > 14...
Page 15 Face-down stacker Power (on/off) switch Face-up stacker Duplex unit Sharp AR-C360P User’s Guide Printer and paper overview > 15...
Page 16: Interface Unit
Interface unit Network interface connector Parallel interface connector USB interface connector Power connector Ventilation openings Sharp AR-C360P User’s Guide Printer and paper overview > 16...
Page 17 Image drum cartridge and toner cartridge (Magenta) Image drum cartridge and toner cartridge (Yellow) Image drum cartridge and toner cartridge (Black) Toner cartridge Image drum cartridge Fuser unit LED heads Sharp AR-C360P User’s Guide Printer and paper overview > 17...
Page 18 Belt unit Drum basket handle Drum basket Sharp AR-C360P User’s Guide Printer and paper overview > 18...
Page 19: Software Supplied
PCL driver. > Documentation Contains documentation in electronic form to describe how to use the printer for day-to-day tasks. > EFI Utilities Contains utilities for use with the EFI Fiery driver Sharp AR-C360P User’s Guide Printer and paper overview > 19...
Page 20: Paper Recommendations
Other types of label stock may damage the printer due to the labels peeling off during the printing process. Suitable types are: > Avery White Laser Label types 7162, 7664, 7666 (A4), or 5161 (Letter) Sharp AR-C360P User’s Guide Printer and paper overview > 20...
Page 21: Paper Input And Output Information
34 lb recommended 15 – 71 lb – 23 lb Based on 24 lb paper 0.004 – 0.008 in Sharp AR-C360P User’s Guide Printer and paper overview > 21 INPUT/ OUTPUT Any Tray Any Stacker Any Tray Face-up Stacker MP Tray...
Page 22 TYPE SIZE Transparencies A4, Letter Glossy paper Sharp AR-C360P User’s Guide Printer and paper overview > 22 WEIGHT INPUT/ OUTPUT 0.004 in Tray 1 or MP Tray Face-up Stacker...
Page 23: Trays And Stackers
Face-down stacker The face-down stacker on the top of the printer can hold up to 500 sheets of 20 lb (80 g/m²) standard paper, and can handle paper Sharp AR-C360P User’s Guide Printer and paper overview > 23...
Page 24: Face-Up Stacker
Legal 13.5 in, Legal 14 in, B4, Tabloid, Tabloid Extra, A3, A3 Wide, A3 Nobi, Custom size (3.9 – 12.9 in wide, 5.8 –18 in long), using paper stocks in the range 20 – 32 lb (75 – 120 g/m²). Sharp AR-C360P User’s Guide Printer and paper overview > 24...
Page 25: Tray And Stacker Examples
Load the paper (face down and top edge towards the right for letterhead paper), press the tab (2) on the paper guide and adjust the guides (3) for a snug fit to the paper. Sharp AR-C360P User’s Guide Printer and paper overview > 25...
Page 26 > Do not load damaged paper. > Do not load paper of different sizes or types at the same time. Gently push the tray back into the printer. Printer and paper overview > 26 Sharp AR-C360P User’s Guide...
Page 27: Using The Mp Tray
Squeeze the handle (1) and open the multi-purpose tray. Fold out the paper support section and swivel out the extension supports (2). Adjust the paper guides (3) to the size of the paper being used. Sharp AR-C360P User’s Guide Printer and paper overview > 27...
Page 28 Do not leave space between the paper and the guides. > Do not exceed the paper capacity of approximately 230 sheets, 100 transparencies or 25 envelopes. Maximum stacking depth is 1in. Printer and paper overview > 28 Sharp AR-C360P User’s Guide...
Page 29: Using The Stackers
(its normal position), paper is ejected to the face-down stacker on the top of the printer. Face-up stacker The face-up exit path is used for heavy paper (cardstock etc.), envelopes, transparencies, and labels. Open the stacker (1). Sharp AR-C360P User’s Guide Printer and paper overview > 29...
Page 30 Flip out the paper support (2). Swivel out the paper support extension (3). Printer and paper overview > 30 Sharp AR-C360P User’s Guide...
Page 31: Control Panel
Control panel The control panel can be swivelled to 90° (maximum) upwards from its base position (1) as required for ease of use. Sharp AR-C360P User’s Guide Control panel > 31...
Page 32: Buttons And Lights
Flashing: indicates error(s) present but printing can continue On: indicates error(s) present and printing cannot continue Display panel Displays status and setup information for the printer and user help information in your chosen language Sharp AR-C360P User’s Guide Control panel > 32...
Page 33: Cancel Button
Switches between online (printer ready to receive data) and offline (printer not ready to receive data) Cancel button Cancels current print job Help button Provides additional textual or image data to supplement what is displayed on the display panel Sharp AR-C360P User’s Guide Control panel > 33...
Page 34: Display Panel Messages
Menu (Functions) information There are three types of menu (functions) information: User menus: accessed by pressing the Enter button, Up- arrow or Down-arrow button on the control panel. These Sharp AR-C360P User’s Guide Control panel > 34 “Appendix A – Display...
Page 35: Configuration Information
In other cases, you can display or print configuration information. Sharp AR-C360P User’s Guide Control panel > 35...
Page 36: Using The Menus
Refer to the section entitled “Appendix B – Menu system” on page 102 menus. “Appendix B – Menu system” on “Getting started” on page 37 for examples of using the Sharp AR-C360P User’s Guide Control panel > 36...
Page 37: Getting Started
This section provides information to help you get started with using your printer. Printer location Check that you have sufficient space for access: > around your printer: 60cm 24in 20cm 8in 100cm 40in Sharp AR-C360P User’s Guide Getting started > 37 60cm 24in...
Page 38: Turning Off/On
> above your printer: Turning Off/On Turning Off Hold down the Shutdown/Restart button (1) on the control panel for more than 2 seconds to start the shutdown process. 70cm 28in Sharp AR-C360P User’s Guide Getting started > 38...
Page 39: Turning On
Shutdown/Restart to turn on the printer. If the printer is turned off (no power), use the On/Off switch to turn on the printer. Please wait as this may take a short time. Sharp AR-C360P User’s Guide Getting started > 39...
Page 40: Checking Current Settings
USB-compatible machines. When connecting multiple printers of the same type, they appear as *****, ***** (2), ***** (3), etc. These numbers depend on the order of connecting or turning on each printer. Sharp AR-C360P User’s Guide Getting started > 40...
Page 41: Connecting The Usb Interface
USB cable when you run the Drivers CD. If you are connecting your printer directly to a stand alone computer proceed to the section entitled “Printer Drivers”. Connecting the network interface Turn off the printer and the computer. Sharp AR-C360P User’s Guide Getting started > 41...
Page 42 Remove the protective cover from the network connector on the printer. Connect an Ethernet cable between the printer and an Ethernet hub. Sharp AR-C360P User’s Guide Getting started > 42...
Page 43: Using The Drivers Cd
NOTE Administrator’s authority is required when installing a network connection. Using the Drivers CD For instructions on installing the drivers and other software, refer to the Software Installation booklet. Sharp AR-C360P User’s Guide Getting started > 43...
Page 44: Operation
Operation Using the printer For full details of how to use the printer and any optional accessories to print jobs efficiently and effectively, please refer to the Printing Guide. Sharp AR-C360P User’s Guide Operation > 44...
Page 45: Consumables And Maintenance
The paper feed rollers and the multi-purpose (MP) tray feed rollers do not have any replacement warning messages. Recommended replacement: after approximately 120,000 Letter sheets. Consumables and maintenance > 45 Sharp AR-C360P User’s Guide...
Page 46: Consumable Item Order Information
42,000 Letter pages continuous print 42,000 Letter pages continuous print 42,000 Letter pages continuous print LIFE 100,000 Letter pages 100,000 Letter pages 30,000 Letter pages avg Sharp AR-C360P User’s Guide ORDER NUMBER AR-C36TBU AR-C36TCU AR-C36TMU AR-C36TYU AR-C36BDR AR-C36CDR AR-C36MDR AR-C36YDR...
Page 47: Replacing Consumables/Maintenance Items
Each consumable or maintenance item comes complete with its own installation details which give full instructions on replacement. You are advised to follow these instructions carefully. Only use genuine Sharp consumables to ensure the best quality and performance from your hardware. Non-Sharp products may damage your printer’s performance and invalidate your warranty.
Page 48 (1). Move the cleaner as shown, using a clean section of the cleaner with each pass. Be careful not to damage the guards (2). Close the top cover. Consumables and maintenance > 48 Sharp AR-C360P User’s Guide...
Page 49: Cleaning The Paper Feed Rollers
Remove items like a wrist watch or bracelet then use the Shutdown/Restart button followed by the On/Off switch to turn the printer off. Open Tray 1 side cover and pull out the paper guide plate (1). Consumables and maintenance > 49 Sharp AR-C360P User’s Guide...
Page 50 Remove Tray 1 completely from the printer. Gaining access through the gap left by Tray 1, wipe the 3 paper feed rollers (2) with a soft cloth lightly moistened with water. Replace Tray 1. Consumables and maintenance > 50 Sharp AR-C360P User’s Guide...
Page 51 Return the paper guide plate to its original position and close Tray 1 side cover. Turn on the printer. Consumables and maintenance > 51 Sharp AR-C360P User’s Guide...
Page 52: Cleaning The Printer Casing
Turn the printer off by using the Shutdown/Restart button followed by the On/Off switch. Wipe the printer surface with a soft cloth moistened sparingly with water or neutral detergent. Use a soft dry cloth to dry the printer surface. Consumables and maintenance > 52 Sharp AR-C360P User’s Guide...
Page 53 Turn on the printer. Sharp AR-C360P User’s Guide Consumables and maintenance > 53...
Page 54: Emptying The Punch Chip Box (Punch Unit Optional Accessory)
Operate the Finisher lever and move the Finisher away from the printer. Pull out the punch chip box, being careful to keep it level so as not to spill any chips. Consumables and maintenance > 54 Sharp AR-C360P User’s Guide...
Page 55 Discard the chips in an appropriate place. Replace the punch chip box carefully into the Finisher. Consumables and maintenance > 55 Sharp AR-C360P User’s Guide...
Page 56 Check that the punch chip box has been replaced correctly then move the Finisher back into position, being careful not to trap your fingers. Sharp AR-C360P User’s Guide Consumables and maintenance > 56...
Page 57: Optional Accessories
The following accessories are available: > Finisher (for stapling or saddle stitching printer output) > Punch unit (to extend Finisher functionality) Accessory order information ITEM Finisher: Finisher Punch Unit: 2-3 hole Sharp AR-C360P User’s Guide Optional accessories > 57 ORDER NUMBER AR-C36TF AR-C36HP...
Page 58: Installing Accessories
For the following accessories, you have to make the appropriate setting in your printer driver(s): > Finisher Refer to the Printing Guide for driver setting details. Sharp AR-C360P User’s Guide Optional accessories > 58...
Page 59: Troubleshooting
In this example Tray 1 is used, the procedure being similar for all other trays. Squeeze the catch (1) on Tray 1 side cover and open the cover. Sharp AR-C360P User’s Guide Troubleshooting > 59 100.
Page 60 Holding it by the tab (2), turn the paper guide outward. Carefully remove the jammed paper. Put the paper guide back into position and close Tray 1 side cover. Sharp AR-C360P User’s Guide Troubleshooting > 60...
Page 61: Open Cover, Paper Jam, Side Cover
Open cover, paper jam, side cover If the MP Tray is open, close it so that the side cover (1) is visible. Pull the release lever (2) and pull open the side cover. Sharp AR-C360P User’s Guide Troubleshooting > 61...
Page 62 Carefully remove the jammed paper. Close the side cover. Sharp AR-C360P User’s Guide Troubleshooting > 62...
Page 63: Open Cover, Paper Jam, Top Cover
Squeeze the top cover handle (1) and open the top cover. Be careful not to touch the fuser unit which is hot after printing. Squeeze the basket handle (2) and raise the drum basket. WARNING! Sharp AR-C360P User’s Guide Troubleshooting > 63...
Page 64 If the fuser unit is hot, wait until it cools before attempting to remove any jammed paper. Holding the fuser unit (4) by the handle, lift it out of the printer and place it on a flat surface. WARNING! Sharp AR-C360P User’s Guide Troubleshooting > 64...
Page 65 Pull up the jam release levers (5) and remove the jammed paper. Carefully replace the fuser unit into the printer and turn the lock lever (6) in the direction shown to lock the fuser unit. Sharp AR-C360P User’s Guide Troubleshooting > 65...
Page 66 If paper is jammed near the paper exit, open the face-up stacker (7). Open the side cover (paper exit) (8) and remove the jammed paper. Sharp AR-C360P User’s Guide Troubleshooting > 66...
Page 67 Close the side cover (paper exit) and then the face-up stacker. Return the image drum basket (9) into position and check it is locked. Sharp AR-C360P User’s Guide Troubleshooting > 67...
Page 68: Paper Jams - Duplex Unit
Paper jams – duplex unit Check duplex unit, paper jam If a Finisher unit is attached to your printer, operate the lever (1) of the Inverter unit to separate the Inverter from the printer. Sharp AR-C360P User’s Guide Troubleshooting > 68...
Page 69 Operate the duplex cover release button (2) and open the cover. Carefully remove any jammed paper. Sharp AR-C360P User’s Guide Troubleshooting > 69...
Page 70 Operate the levers (3) and pull out the duplex unit. Holding the front top cover by the grip (4), push it gently inwards and raise it. Sharp AR-C360P User’s Guide Troubleshooting > 70...
Page 71 Remove any jammed paper. In similar manner, check for and clear any paper jammed under the rear top cover. Sharp AR-C360P User’s Guide Troubleshooting > 71...
Page 72 Replace the two top covers. Raise the front cover of the duplex unit. Sharp AR-C360P User’s Guide Troubleshooting > 72...
Page 73 Push the duplex unit back into position. If you detached a Finisher unit to gain access to the duplex unit, replace the Finisher unit. Sharp AR-C360P User’s Guide Troubleshooting > 73...
Page 74: Paper Jams - Finisher (Optional Accessory)
You will need this to be able to clear the paper jam. The following paragraphs explain what to do for each of the indicated numeric codes. 591, 592, 593, 599/ 643, 645 (paper jam around Finisher) Remove any paper at the Finisher paper exit. Sharp AR-C360P User’s Guide Troubleshooting > 74...
Page 75 Operate the Finisher lever (1) and move the Finisher away from the Inverter. Open the Finisher top cover. Sharp AR-C360P User’s Guide Troubleshooting > 75...
Page 76 Carefully remove any jammed paper. Close the Finisher top cover. Sharp AR-C360P User’s Guide Troubleshooting > 76...
Page 77: (Paper Jam In Finisher)
Move the Finisher back into position and connect it to the Inverter. 594, 597, 598/ 644, 646 (paper jam in Finisher) Operate the Finisher lever (1) and move the Finisher away from the Inverter. Sharp AR-C360P User’s Guide Troubleshooting > 77...
Page 78 Open the Finisher front cover (2). Continue to turn the lower knob (3) clockwise until any jammed paper is completely ejected. Sharp AR-C360P User’s Guide Troubleshooting > 78...
Page 79 Remove the ejected paper. Close the Finisher front cover. Sharp AR-C360P User’s Guide Troubleshooting > 79...
Page 80 Open the Finisher right side cover. Carefully remove any jammed paper. Sharp AR-C360P User’s Guide Troubleshooting > 80...
Page 81 Close the Finisher right side cover. Move the Finisher back into position and connect it to the Inverter. Sharp AR-C360P User’s Guide Troubleshooting > 81...
Page 82: Paper Jam In Finisher/Punch Unit)
590 (paper jam in Finisher/Punch unit) Operate the Finisher lever (1) and move the Finisher away from the Inverter. Move the tab (2) on the right side of the Finisher to align it with the mark (3). Sharp AR-C360P User’s Guide Troubleshooting > 82...
Page 83 Open the Finisher top cover. Carefully remove any jammed paper. Close the Finisher top cover. Sharp AR-C360P User’s Guide Troubleshooting > 83...
Page 84: Check Inverter, Paper Jam
Move the Finisher back into position and connect it to the Inverter. Check Inverter, paper jam Operate the Finisher lever (1) and move the Finisher away from the Inverter. Sharp AR-C360P User’s Guide Troubleshooting > 84...
Page 85 Squeeze the recessed handle (2) and open the left side cover of the Inverter. Carefully remove any jammed paper. Sharp AR-C360P User’s Guide Troubleshooting > 85...
Page 86 Close the Inverter left side cover. Move the Finisher back into position and connect it to the Inverter. Sharp AR-C360P User’s Guide Troubleshooting > 86...
Page 87 Operate the Inverter lever (3) and separate the Inverter from the printer. Open the right side door (4) of the Inverter. Sharp AR-C360P User’s Guide Troubleshooting > 87...
Page 88 Remove any jammed paper. Close the right side door. Sharp AR-C360P User’s Guide Troubleshooting > 88...
Page 89: Avoiding Paper Jams
Remove the sheets, jog them into alignment and reload them. Adjust the paper stop and paper guides of the tray, or the manual feed guide on the MP Tray to align the media properly. Adjust the orientation as required. Sharp AR-C360P User’s Guide Troubleshooting > 89...
Page 90 The media weight or type have been wrongly set. SUGGESTED REMEDY Wipe the roller with a cloth moistened with water. Replace the feed rollers. Select the correct printer menu settings for [Media Weight] and [Media Type]. Sharp AR-C360P User’s Guide Troubleshooting > 90...
Page 91: Dealing With Unsatisfactory Printing
Thickness and type of paper are inappropriate. Recycled paper is being used. Paper is moist or dry. Sharp AR-C360P User’s Guide Troubleshooting > 91 STEPS TO TAKE Wipe the LED head with a LED lens cleaner or with a soft cloth.
Page 92 Recycled paper is used. Glossiness is not The thickness and type uniform. of the paper are incorrectly set. Sharp AR-C360P User’s Guide STEPS TO TAKE Replace the image drum cartridge. Replace the toner cartridge. Wipe it lightly with a soft cloth.
Page 93: Staple Jams - Finisher (Optional Accessory)
Check Finisher, Staple Jam When the display indicates a staple jam has occurred, clear the jam as follows: Open the Finisher front cover. Turn the knob in the direction indicated until the colored indicator appears. Sharp AR-C360P User’s Guide Troubleshooting > 93...
Page 94 Remove any paper that awaits stapling in the paper ejection area. Pull out the staple unit. Sharp AR-C360P User’s Guide Troubleshooting > 94...
Page 95 Turn the knob in the direction indicated to move the stapler to the front. Grip both sides of the staple cartridge, pull it up and remove Raise the staple cartridge gate. Sharp AR-C360P User’s Guide Troubleshooting > 95...
Page 96 Remove all staples that are emerging from the staple case. Return the staple cartridge gate to its original position. Replace the staple cartridge. Sharp AR-C360P User’s Guide Troubleshooting > 96...
Page 97 Ensure that the staple cartridge is securely installed back into the staple unit then push the staple unit fully home. Close the Finisher front cover, being careful not to trap your fingers. Sharp AR-C360P User’s Guide Troubleshooting > 97...
Page 98: Specifications
230 VAC, 50 Hz +/- 2Hz Operating: 1,500 W maximum, 750 W typical Standby: 1,300 W maximum, 200 W typical Power save: <45 W Operating: 50 – 90°F/20 – 80%RH Off: 32 – 110°F/10 – 90%RH Sharp AR-C360P User’s Guide Specifications > 98...
Page 99 ITEM Noise level SPECIFICATION Operating: 53dBA maximum Standby: 40dBA maximum Power save: 40dBA maximum after 30 mins background level Sharp AR-C360P User’s Guide Specifications > 99...
Page 100: Appendix A - Display Panel Messages
You can access help details by pressing the HELP button. The printer has tried to take paper from a tray that has been removed. Ensure that tray tttttt is correctly located or put tray tttttt loaded with paper back into the printer. Sharp AR-C360P User’s Guide...
Page 101 Check Image Drum cccccc Please see HELP for details Sharp AR-C360P User’s Guide Appendix A – Display Panel Messages > 101 COMMENT Additional paper has been detected after a paper jam has been cleared. Open tttttt side cover to check for additional paper.
Page 102: Appendix B - Menu System
The remainder of the menus above are intended for more specialized usage and are not described further here. For full details of using all menus to configure and use the printer, refer to the Configuration Guide. Sharp AR-C360P User’s Guide Appendix B – Menu system > 102...
Page 103: Configuration
Finisher Count ITEM VALUE Staple nnnnnn Punch nnnnnn Finisher nnnnnn Sharp AR-C360P User’s Guide Appendix B – Menu system > 103 DESCRIPTION Displays number of color printed pages converted to Letter equivalent. Displays number of monochrome printed pages converted to Letter equivalent.
Page 104: Supplies Life
(n.nK) Network The items and settings displayed are specific to your system. Full details are given in the Configuration Guide. Sharp AR-C360P User’s Guide Appendix B – Menu system > 104 DESCRIPTION Displays the remaining life span of the xxxx...
Page 105: Paper Size In Tray
Serial Number xxxxxxxxxxxxxxx Asset Number xxxxxxx CU Version xx.xx PU Version xx.xx.xx Sharp AR-C360P User’s Guide Appendix B – Menu system > 105 DESCRIPTION Displays detected paper size of Traym. Displays detected paper size of the MP Tray. DESCRIPTION Displays serial no. of the printer.
Page 106: Configuration Example - Monochrome Pages Printed
Press the Enter button and the monochrome page count is displayed. Press the Online button to exit menu mode and return to the ready to print status. Sharp AR-C360P User’s Guide Appendix B – Menu system > 106 DESCRIPTION Displays total RAM memory installed in the printer.
Page 107: Print Pages
Usage Report Execute Statistics Log Execute Error Log Execute E-mail Log Execute PrintMe Log Execute Sharp AR-C360P User’s Guide Appendix B – Menu system > 107 DESCRIPTION Prints the PostScript sample page. Prints printer configuration details. Prints EFI job log details.
Page 108: Print Information Example - Demonstration Page
Demo page is highlighted. Press the Enter button to select this Item and the demo page is printed. After printing, the printer returns to ready to print status. Sharp AR-C360P User’s Guide Appendix B – Menu system > 108...
Page 109: Print Secure Job
Delete: When you select Delete, you are prompted to recheck by Yes/No display, and selecting Yes deletes all jobs. Sharp AR-C360P User’s Guide Appendix B – Menu system > 109 DESCRIPTION Specifies a feed tray. Indicated only when Tray2–4 implemented.
Page 110 Card stock Rough Glossy User Type1 User Type2 User Type3 User Type4 User Type5 Sharp AR-C360P User’s Guide DESCRIPTION Sets paper in Traym. Sets Custom paper width for Traym. Sets for the direction perpendicular to the direction of paper movement.
Page 111 Ultra Heavy 3 A3 Nobi A3 Wide Tabloid Extra Legal 14 Legal 13.5 A5/A6 Postcard Sharp AR-C360P User’s Guide DESCRIPTION Sets media weight for Traym. The printer detects A3 Nobi, A3 Wide and Tabloid Extra sizes as the same. Use this...
Page 112 216 (L) – 328 3.5 – 11.0 (L) – 11.7 (A) – 47.2 inch 90 – 279 (L) – 297 (A) – 1200 Sharp AR-C360P User’s Guide DESCRIPTION Sets paper size for MP Tray. Sets Custom paper width for the MP Tray.
Page 113 Ultra Heavy 1 Ultra Heavy 2 Ultra Heavy 3 Normal Tray When Mismatching Do Not Use Sharp AR-C360P User’s Guide DESCRIPTION Sets the media type for MP Tray. Sets the media weight for MP Tray. Tray selection/switching uses this tray as the normal tray.
Page 114: System Adjust
120 sec 150 sec 180 sec 210 sec 240 sec 270 sec 300 sec Sharp AR-C360P User’s Guide Appendix B – Menu system > 114 DESCRIPTION Sets the period after which power save mode starts. When Online is selected, you must...
Page 115 +0.01 – +0.08 -0.08 – -0.01 0.00 +0.25 – +2.00 -2.00 – -0.25 0.00 +0.01 – +0.08 -0.08 – -0.01 Sharp AR-C360P User’s Guide DESCRIPTION Sets the printing operation when insufficient toner is detected. Continue: the printer can continue printing while remaining online.
Page 116 -0.08 – -0.01in 0.00 +0.25 – +2.00 -2.00 – -0.25 0.00 +0.01 – +0.08 -0.08 – -0.01 Sharp AR-C360P User’s Guide DESCRIPTION During the flip-side printing of duplex printing, adjusts the location of the whole printing image (0.25 mm, 0.01in interval)
Page 117 Color Setting +1 – +2 -2 – -1 Drum Cleaning Hex Dump Execute Appendix B – Menu system > 117 Sharp AR-C360P User’s Guide DESCRIPTION Used for micro adjustment when very visible faded print results or light specks (or streaks)
Page 118: Menus Example 1 - Tray 1 Transparencies
Press the Enter button to select this value. Check that an asterisk (*) appears beside Transparency. Press the Online button to exit menu mode and return to the ready to print status. Sharp AR-C360P User’s Guide Appendix B – Menu system > 118...
Page 119: Menus Example 2 - Mp Tray Paper Size
Press the Enter button to select this value. Check that an asterisk (*) appears beside the chosen size. Press the Online button to exit menu mode and return to the ready to print status. Sharp AR-C360P User’s Guide Appendix B – Menu system > 119...
Page 120: Index
Status information34 enter button33 features optional9 standard7 help button33 indicator light attention32 ready32 interface Ethernet41 parallel40, 41 Sharp AR-C360P User’s Guide USB40, 41 maintenance items order details46 replacing45 menu Admin Setup102 Calibration102 Configuration102, 103 Menus102, 109 Print Information107 Print Pages102...
Page 121 Sharp AR-C360P User’s Guide Index > 121...

Sharp AR-C360P User Manual

Copyright Information

Notes, Cautions and Warnings

Introduction

Printer and Paper Overview

Control Panel

Getting Started

Operation

Consumables and Maintenance

Optional Accessories

Troubleshooting

Specifications

Appendix A - Display Panel Messages

Appendix B - Menu System

Index

Quick Links

Need help?

Questions and answers

Related Manuals for Sharp AR-C360P

Summary of Contents for Sharp AR-C360P

Table of Contents