Kyocera Mita KM-7530 Operation Manual page 110

Section 5 OTHER CONVENIENT FUNCTIONS
3 Selecting between 1-sided or 2-sided copies
This procedure selects the type of finished copies to be made
between 1-sided and 2-sided.
1 With the content of the "Basic" tab displayed, touch the "1
sided/2 sided" key. The "1 sided/2 sided" screen will be
displayed.
Inch specifications
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
1-sided
11x8 1 / "
2
Select Original
paper
type
None AMS
Reduce
Finished
/Enlarge
Basic Quality
Metric specifications
Ready to Job build.
Set original. Press Start key.
Job Build -Step 1
1-sided
Select Original
paper
type
None AMS
Reduce/
Finished
Enlarge
Basic Quality
NOTE
The setting in regard to making either 1-sided or 2-sided copies can
only be made in the first step of the job build mode and will apply to
all steps in the copy job.
2 Touch the "1 sided" key or the "2 sided" key, as appropriate,
and then select the binding direction you want for the
finished copies.
Follow the instructions on the right side of the touch panel
and verify the direction in which the originals were set.
Inch specifications
Ready to Job build.
Place originals then press Start key.
1 sided/ 2 sided copy
Finished
1 sided Open from
copy left
2 sided Open from
copy right
Open from
top
Metric specifications
Ready to Job build.
Set original. Press Start key.
1-sided / 2-sided Copy
Finished
1-sided Left
Copy binding
2-sided Right
Copy binding
Top
binding
IMPORTANT!
If the designation for the direction that the originals are set is not
correct, copying may be accomplished incorrectly.
5-64
1 sided copy
Insert
page
1 sided/
2 sided
1 sided copy-Left
Back Edge
Finished page #:0
Orig. set
direction
Edit
1-sided Copy
Insert
blank page
1-sided/
2-sided
1-sided Copy-Left
Back Edge
Finished page #: 0
Orig. set
direction
Edit
Back
Check direction
Check direction of
original top side.
Left top
Rear
corner
Back
Check direction
Check direction of
original.
Left top
Back Edge
corner
3 Touch the "Close" key. The touch panel will return to the
screen in step 1.
4 Selecting how to finished up the copy sets
If the optional Document Finisher is installed on your copier, this
procedure lets you select whether to staple or hole punch the finished
copy sets.
1 With the content of the "Basic" tab displayed, touch the
Set
"Finished" key. The "Finished" screen will be displayed.
Inch specifications
End
Ready to Job build.
Place originals then press Start key.
Job Build - Step1
11x8
Select
paper
None
Finished
Basic
Set
Metric specifications
End
Ready to Job build.
Set original. Press Start key.
Job Build
Select
paper
None
Finished
Basic
NOTE
The setting in regard to how the copy sets will be finished can only be
made in the first step of the job build mode and will apply to all steps
in the copy job.
2 Select how you want the copy sets to be finished by touching
the "Staple mode" key, the "Saddle Stitch" ["Center Staple" ]
key or the "Punch mode" key, as appropriate.
Follow the instructions on the right side of the touch panel
Set
and verify the direction in which the originals were set.
Inch specifications
Close
Ready to Job build.
Place originals then press Start key.
Finished
Set
Metric specifications
Close
Ready to Job build.
Set original. Press Start key.
Finished
Group
None
1 set
IMPORTANT!
If the designation for the direction that the originals are set is not
correct, copying may be accomplished incorrectly.
1-sided 1 sided copy
1 / "
2
Original
1 sided/
type 2 sided
1 sided copy-Left
AMS Back Edge
Finished page #:0
Reduce Orig. set
/Enlarge direction
Quality Edit
-Step 1
1-sided 1-sided Copy
Original 1-sided/
type
2-sided
1-sided Copy-Left
Back Edge
AMS
Finished page #: 0
Reduce/ Orig. set
Enlarge
direction
Quality Edit
Offset Staple Punch
No cover No cover
Staple Punch
None
mode mode
1 set
Saddle
Stitch
Group
Staple Punch
None None
Staple Punch
None
Mode Mode
1 set
Center
Staple
Set
End
Insert
page
Set
End
Insert
blank page
Set
Back Close
Check direction
Check direction of
original top side.
Left top
Rear
corner
Set
Back Close
Check direction
Check direction of original.
Left top
Back Edge
corner