Quick guide Satellite dish The satellite dish must have a clear view to the satellites. Mount the satellite dish according to the fitting instructions. In case you already have a satellite dish mounted, note that you need a Universal LNB which works on the frequencies 10.70- 12.75 GHz to be able to handle digital signals.
Quick guide One antenna/one LNB configuration Select this alternative if you have one (1) LNB mounted on the an- tenna. • Press opt to view the predefined channel. LNB type Select the correct LNB type for your configuration. The most com- mon values, including Universal LNB, are selectable with the cur- sor left and cursor right buttons.
Nokia operates a policy of continuous development. Therefore we reserve the right to make changes and improvements to any of the products described in this manual without any prior notice.
Nokia Corporation, Nokia Home Communications (“Nokia”). The Agreement authorizes You to use the Software specified in Clause 1 below and which is included in this Nokia digital TV receiver. This is an agreement on end-user rights and not an agreement concerning sale.
Page 7
Nokia if You fail to comply with mental corporations, or their separate business any provision of this Agreement. In such an event,...
• Do not allow the unit to be exposed to hot, cold or humid conditions. • Service should be carried out only at a Nokia Authorised Service Centre. • Please note that the only way to isolate the Mediamaster completely from the...
REMOTE CONTROL This section describes how to operate the Mediamaster using the buttons on the remote control. The standby button has double functions. One function is carried out if you press the button gently once and the other function is carried out if you hold down the button for a few seconds. Some of the functions can also be carried out using the buttons on the front panel.
FRONT AND REAR PANEL Front panel to change channels open the lid in order and to move in menus to insert the CA module and the smart card Slot Slot for a CA module for inserting of a with a smart card Viaccess smart card Indica- Indica-...
Service Provider. Note: CA modules and smart cards are only distributed by Serv- ice Providers and special distributors, not by Nokia. After inserting a card, leave it in the slot permanently. Do not re- move it again, unless you will be asked to do so. This is impor-...
INSTALLATION OF THE MEDIAMASTER The box for your Mediamaster should contain the following items: • the Mediamaster • remote control with 2 AAA batteries • SCART cable (fully connected 1.0 metre) • mains cable • owner’s manual with software license agreement Mains SCART Remote...
• Connect the TV aerial to the RF input socket on the analogue receiver. In order to switch the signal from the dish between the ana- logue and digital receivers, you need a Nokia smart switch (at Mediamaster A B in the diagram) or a Universal Twin LNB.
INSTALLATION OF THE MEDIAMASTER Connecting a HiFi system • Connect an RCA stereo cable from the AUDIO L R sockets on the Mediamaster to the LINE, AUX, SPARE or EXTRA in- put sockets on your HiFi system. • If available you can connect an RCA single cable from the DIG- ITAL AUDIO socket on the Mediamaster to a HiFi system equipped with digital audio input.
FIRST TIME INSTALLATION General information Once you have correctly connected the Mediamaster, you also have to perform a “First time installation.” During this procedure, helpful information is displayed at the bottom of the menus. Please note! The select button always confirms a selection within these menus, and pressing it will take you to the next step in the instal- lation process.
FIRST TIME INSTALLATION One antenna/one LNB configuration Select this alternative if you have one (1) LNB mounted on the antenna. • Press opt to view the predefined channel. LNB type Select the correct LNB for your configuration. The most common values, including Universal LNB, are selectable with cursor left/ cursor right.
Page 17
FIRST TIME INSTALLATION Typical connection of a two-way DiSEqC switch: • Connect the cable from the LNB intended for channels from the ASTRA satellite (or THOR) to the connector marked LNB 1 (A) on the switch. • Connect the cable from the HOTBIRD satellite (or SIRIUS) to the connector marked LNB 2 (B).
• From the “Antenna/Satellite selection” menu select alternative 3 “Motor Antenna Configuration” and press select. Type of motor • Select SATSCAN (Astra) if it is a Nokia SatScan motor. • Select DiSEqC (Hotbird) in case the motor you use is control- led by DiSEqC commands.
FIRST TIME INSTALLATION Remove limits In case you need to remove limits. When you perform this command the motor will also turn itself to the 0° (Zero) position. However, next time you select a channel the motor will turn to its proper position.
FIRST TIME INSTALLATION Advanced manual search The information you need to enter in this menu is available in magazines covering satellite TV reception or on the Internet. You can use this menu if you are looking for some “special” chan- nels (i.e.
NAVI™ BARS NAVIGATOR General information Bookmark Bookmark name • Press select to open the Navi™ Bars Navigator. In order to select TV/Radio channels and to change system set- tings you will use the Navi™ Bars Navigator. In this manual the name is shortened to Navigator.
NAVI™ BARS NAVIGATOR ☛ Control folder User pref Banner time-out When you switch channels, an information banner will be shown for a few seconds. You can select how long the banner will be shown. Volume bar Select whether or not you want the volume bar to appear on the screen when you change the volume.
Page 23
NAVI™ BARS NAVIGATOR Important about editing channels Before you start you must select which list, TV or radio, you want to edit. If you are watching TV and press select and choose Edit channels, you can only edit TV channels. If you are listening to radio channels you can edit radio channels.
Page 24
NAVI™ BARS NAVIGATOR Delete list If you want to delete a Favourite list, select the list with cursor left/cursor right and press select. Rename list You can give an existing list a new name by following the instruc- tions under the headline “How to give a specific name” on page Rearrange lists If you have created several Favourite lists you can determine the sequence in which the lists will appear.
NAVI™ BARS NAVIGATOR From here you can lock (and later unlock) channels in any of the lists in order to prevent e.g. your children from watching. Beside the channel name three different symbols can be shown. ( channel you have not previously visited. = channel is scram- bled according to the service information.
NAVI™ BARS NAVIGATOR • When you get the message on the screen that ”you have found X new TV-channels and X new radio channels”, press select to save the new channels. The new channels will be saved and added to the TV and radio lists.
NAVI™ BARS NAVIGATOR Timer setup • First, select Channel List with cursor left /cursor right. • Then, step to Channel to select the desired TV/Radio channel. • Set the date using the numerical buttons (yy/mm/dd). • If you enter a wrong digit you can erase it with cursor left. •...
Please refer to page 19. Update channels via a PC On the Nokia web site (www.nokia.com) you can download a Windows™ software for updating the channel lists via the serial port. The serial port connector can be found on the back of the Mediamaster (See page 10) .
NAVI™ BARS NAVIGATOR Picture format If you have a TV set with the 4:3 picture format and the transmis- sion is in 16:9, you can select “Fullscreen” or “Letterbox”. Fullscreen will fill up the screen but cut off some information on the left and right sides.
NAVI™ BARS NAVIGATOR ☛ Settings folder Access ctrl To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234. The following settings can be altered from this menu. Access Control Select “Yes”...
This will damage the software and the receiver will have to be sent in for service! Please check the latest updates for your receiver at Nokia’s web site (www.nokia.com). On the Nokia web site (www.nokia.com) you can download a Windows™...
VIEWING MODE General information The following describes the basic functions of your Mediamaster while watching satellite TV or listening to satellite radio. Some of the functions described here are dependent on the Service Provider and can only be used if they are included in the transmitted programme information.
VIEWING MODE Extended programme information The Mediamaster can display information about programmes cur- rently being broadcasted as well as those that will be broadcasted next. This procedure is the same for both TV and radio mode. By pressing info while watching TV you will get the “Programme information”...
VIEWING MODE TV release (0) With the 0 button you can toggle between analogue terrestrial TV, video, analogue and digital satellite TV signals. Teletext Pressing txt will open a teletext page (if teletext is transmitted.) Select teletext pages with the numeric buttons on the remote control.
GLOSSARY OF TERMS AC-3 Network Multichannel digital audio encoding system. A number of digital channels transmitted from one source. Grouped under separate headings in the channel Access control list. A feature that allows parents to ”lock” programmes that they consider unsuitable for children. A ”locked” chan- nel or programme can only be ”unlocked”...
Page 36
PROBLEM SOLVING Problem Possible causes What to do The LED on the front panel does Mains cable is not connected. Check that the mains cable is plugged not light up/is not lit. into the power socket. The left LED is shining red The Mediamaster is in standby Press the standby button to bring the mode.
PROBLEM SOLVING Disconnect the mains cable. Recon- After software update or when you System failure. nect it, the Mediamaster will try to start-up your Mediamaster both download new software from satellite. LEDs simultaneously blink red. Try to update the system software via serial cable connection.
TECHNICAL SPECIFICATIONS Transmission standards Front panel DVB, MPEG 2 2 LEDs, Buttons: (standby, progr. number up and down) LNB / Tuner input Conditional Access system Connector 1x F-type (LNB) Embedded Viacccess. One PCMCIA Interface for a RF input frequency 950-2150 MHz Common Interface CA-module.
MENUS SCREEN STRUCTURE First time installation Channel Search in Progress Language preferences Antenna/satellite selection Channel search Antenna adjustment “First time English Deutsch NB type One antenna/One LNB config installation” Automatic search Français Espanol LNB offset voltage CNN Radio Multisatellite/DiSEQqC Switch config Manual search menu Italiano...