Nokia owner's manual mediamaster 9820 t (33 pages)
Summary of Contents for Nokia Mediamaster 230 T
Bedienungsanleitung User Guide Instrucciones de uso Käyttöohje User Guide Bruksanvisning...
Nokia hereby declares that this digital receiver, Mediamaster 230 T, is in con- formity with essential requirements and other relevant provisions of Directive 1999/5/EC. This Terminal Equipment is intended for connection to the analogue Public Switched Telephone Networks (PSTNs), in which network addressing, if provided, is by means of Dual Tone Multiple Frequency (DTMF) signalling.
Connecting a TV and a video recorder SCART Switching on for the first time • Plug in your Mediamaster. • The “First time installation” menu is shown • Press the select button on the remote control to start the installation procedure. Language •...
Time adjustment The time is adjusted ± 1/2 hour at a time by using cursor up/ down. You can also adjust the minutes by using cursor left/right. • Press select to finish the First time installation and watch TV channels. GB 4 Quick Guide...
Nokia Corporation, Nokia Home Communications (“Nokia”). The Agreement authorizes You to use the Software specified in Clause 1 below and which is included in this Nokia digital TV receiver. This is an agreement on end-user rights and not an agreement concerning sale.
Nokia Mediamaster software end-user license without notice from Nokia if You fail to comply with any provision of this Agreement. In such an event, You must immediately return at Your own cost, this Nokia digital TV receiver, and all related material to the place of purchase.
• Do not allow the unit to be exposed to hot, cold or humid conditions. • Service should be carried out only at a Nokia Authorised Service Centre. • Please note that the only way to isolate the Mediamaster completely from...
Note: If 0 is entered as the first digit, the TV Release func- tionality is activated (see below). To toggle between the 230 T and any equipment connected to the AUX Scart; e. g. a Video recorder or a satellite receiver.
TV/VCR for an RF-cable to the aerial input of the TV or VCR Power supply only for connection of a NOKIA indoor TV aerial with signal amplifier. 5V 30 mA. Aerials from other manufacturers may NOT be powered from this...
Service Provider. Note: CA modules and smart cards are only distributed by Serv- ice Providers and special distributors, not by Nokia. After inserting a card, leave it in the slot permanently. Do not re- move it again, unless you will be asked to do so. This is impor-...
Connecting the Mediamaster The box for your Mediamaster should contain the following items: • the Mediamaster • remote control with 2 AAA batteries • SCART cable (fully connected; 1,0 metre) • mains cable • RF cable • Owner’s manual with software license agreement About the SCART sockets The rear panel of the Mediamaster is equipped with 2 SCART sockets (see diagram).
• Place the aerial by the window and directed towards the TV transmitter, if possible. • The Nokia aerial with an amplifier is recommended as it may provide a stronger signal. • The strength of the TV signal varies according to reflections from e.
Connecting the Mediamaster General There are many different types of TV/VCR and other equipment that you can connect to the Mediamaster. In this manual you will see some of the most common ways to connect your equipment. If you have problems with your connections and need help, con- tact your dealer.
Connecting the Mediamaster Connecting a HiFi system • Connect an RCA/Cinch stereo cable from the AUDIO L R sock- ets on the Mediamaster to the LINE, AUX, SPARE or EXTRA input sockets on your HiFi system. • If available you can connect an RCA/Cinch single cable from the DIGITAL AUDIO socket on the Mediamaster to a HiFi sys- tem equipped with digital audio input.
First time installation General information Once you have correctly connected the Mediamaster, you also have to perform a “First time installation.” During this procedure, helpful information is displayed at the bot- tom of the menus. Please note! The select button always confirms a selection within these menus, and pressing it will take you to the next step in the instal- lation process.
First time installation Channel search in progress This menu will be shown as long as the Mediamaster is search- ing for TV and radio channels. All channels found will be listed on the screen. Please note that the search procedure may take a few minutes. You can cancel the search at any time by pressing select.
Viewing mode General Information The following describes the basic functions of your Mediamaster while watching terrestrial digital TV . Some of the functions described here are dependent on the Service Provider and can only be used if they are included in the transmitted programme information.
Viewing mode Extended programme information The Mediamaster can display information about programmes cur- rently being broadcasted as well as those that will be broadcasted next. This procedure is the same for both TV and radio mode. By pressing info while watching TV you will get the “Programme information”...
Viewing mode External equipment Use the 0 (zero) button to toggle between the 230 T and any equipment connected to the AUX Scart; e. g. a Video recorder or a satellite receiver. Teletext Pressing txt will open a teletext page (if teletext is transmitted.) Select teletext pages with the numeric buttons on the remote control.
Navi Bars General information • Press select to open the Navi Bars. In order to select TV and radio channels and to change system settings you will use the Navi Bars. The horizontal row contains folders, e. g. All TV, Settings and so on.
Navi Bars The “Control” and “Settings” folders Both of these system folders contains a few bookmarks. Each of these bookmarks contains menus from where you can make different settings. The system folders can not be deleted. The manual will now explain the different settings you can per- form from the Control and Settings folders, starting with the bookmarks from the Control folder.
Navi Bars ☛ Control folder From these menus you can create and edit favourite channel lists. You can add, delete, rename and arrange the order of the chan- nels within the favourite lists. The “All TV” list might contain lots of channels. By creating your own favourite lists you can make channel handling more convenient.
Navi Bars • Enter the name as follows: Press the numerical button corresponding to the character you want: once for the first character, twice for the second and so The available characters are listed below. * # & % $ , ! ; - + ) / \ @ ^ 1 a b c 2 Å...
Navi Bars Add/Delete channels From this menu you add and remove the channels in your favour- ite lists. You use the “All TV” or “All radio” list as basis to select the channels from. A channel is added or removed from the list by pressing info. The square to the right on a line will be empty for removed channels, and will contain an “x”...
Selecting Yes also means that the external device during its searching for a suitable Bluetooth receiver to send images to, should be able to find the 230 T. If it does not find it, the reason might be that No is selected.
How to enter a new name, please refer to page 23. Bluetooth passkey The very first time you want to send an image to the 230 T a pass- key has to be entered in the transmitting device. By default this passkey is set to 123456789 on this line.
Navi Bars ☛ Control folder General You can make the Mediamaster to start and stop at a predefined time. The timer function is very useful when you want to record a pro- gramme and you are unable to start/stop the recording event yourself, or when you just want to be reminded of the start of a programme you do not want to miss.
Navi Bars ☛ Settings folder When you want to search for channels at a later time. To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234. A channel search procedure can be performed in different ways: Automatic, Manual or Advanced manual search.
Navi Bars ☛ Settings folder To open this menu you will be asked to enter your access code. From the factory the access code is set to 1234. From here you can adjust the audio/video settings for your Media- master. TV screen format Select your TV screen format.
Navi Bars ☛ Settings folder In order to keep the Mediamaster up-to-date, it will be possible to download new versions of the system software (SW). New software may include new or improved features for existing menus. Enter this menu to check for new software. If new software is available you will get information in the menu on how to proceed.
Glossary AC-3 Multichannel digital audio encoding system. Access code A four-digit code stored in the Mediamaster. Used to lock/unlock the Mediamaster. Access control A feature that allows parents to ”lock” programmes that they consider unsuitable for children. A ”locked” chan- nel or programme can only be ”unlocked”...
Troubleshooting Problem The LED on the front panel does not light up/is not lit. The left LED is shining red The remote control is not working. You have forgotten your PIN code. During the first time installation when the Mediamaster tries to find and store channels you get the message “No channels found”.