Detection Area Setting - Hitachi KP-FD30 Operation Manual

●● ＣＡＭＥＲＡ ＴＩＴＬＥ ＭＥＮＵ ●●
ＭＯＤＥ ：ＯＦＦ
ＲＥＴ
ＥＮＤ
MODE: OFF
●● ＣＡＭＥＲＡ ＴＩＴＬＥ ＭＥＮＵ ●●
ＭＯＤＥ ：ＴＯＰ
０１２３４５６７８９
ＡＢＣＤＥＦＧＨＩＪＫＬＭ
ＮＯＰＱＲＳＴＵＶＷＸＹＺ
！？＃＆（ ） ， ． ：；～＊％
＋－×／＝" '
ＳＰＡＣＥ ← → ＲＥＳＥＴ
ＰＯＳＩＴＩＯＮ ＲＥＴ ＥＮＤ
□□□□□□□□□□□□□□□□□□□□□□□
MODE: TOP/( or BOTTOM)
●Title positioning setting [ POSITION ]
Press the Up and Down buttons to shift the characters
horizontally. Afterwards, press Set to confirm the display
position and return to the main menu.
●● ＡＬＣ ＭＥＮＵ ●●
ＭＯＤＥ ：ＡＶＥ
ＬＥＶＥＬ ： ０００
ＲＥＴ
ＥＮＤ
ALC MODE: AVE
●● ＡＬＣ ＭＥＮＵ ●●
ＭＯＤＥ ：ＡＲＥＡ
ＡＲＥＡ ＳＥＬＥＣＴ：ＮＯ．１
ＬＥＶＥＬ ： ０００
ＲＥＴ
ＥＮＤ
MODE: AREA
● Detection area setting
Shift the cursor to Area Select and press the Set button to
display the detection area select menu. There are 9 light
detect areas selected by the Up and Down buttons.
Select the areas from nos. 1 to 9 that include the subject
of main interest. After deciding the detection areas, press
the Set button to return to the ALC menu.
Display on/off and position
[OFF, TOP, BOTTOM]
Return (Return to the main menu)
End (Return to the normal screen)
（3）Auto level control［ALC MENU］
Automatic light control mode is set up. This control is reflected
Display on/off and position
[OFF, TOP, BOTTOM]
during automatic level control operation of an automatic iris
diaphragm lens, AGC, AES, etc.
Input character select table
There are the following three modes in automatic exposure
Blank cursorshift(left,right) character
, ,
delete
control.
Display position (left,right),
Return, end
①[AVE]
Input charactet display
(24 alphanumeric characters)
②[AREA]
③[PEAK/AVE]
Select ALC mode
[AVE, AREA, PEAK/AVE]
Video level(light volume)adjust
(*)
［-128～000～+127］
Return(Return to the main menu)
End(Return to the normal screen)
(*)Press the Set button;
the numerals flash. Press the Up
and Down buttons to change the
video level.
Select ALC mode
[AVE, AREA, PEAK/AVE]
Go to the area select menu
Video level(light volume)adjust
(*)
[-128～000～+127]
Return(Return to the main menu)
End(Return to the normal screen)
(*)Press the Set button;
the numerals flash. Press the Up
and Down buttons to change the
video level.
ＣＡＭＥＲＡ ＮＯ．１
Camera title position setting
Responds to the average lighting over a broad area.
Exposure is controlled only by the luminosity level of
specific area. (Scanning area is selectable from 9 area.)
The peak level and the average level are used together
and exposure is controlled.
(The ratio of a peak value and average value is changeable.)
ＡＲＥＡ（ＡＬＣ）
ＮＯ．１
┏━━━━━━┓
┃ ┃
┃ ┃
┗━━━━━━┛
Detect area indication
●● ＡＬＣ ＭＥＮＵ ●●
ＭＯＤＥ ：ＰＥＡＫ／ＡＶＥ
ＰＫ／ＡＶ ： ０／１００
ＬＥＶＥＬ ： ０００
ＲＥＴ
ＥＮＤ
MODE: PEAK/AVE
Note:
If the ratio of (PEAK) is enlarged, a picture level may
flicker. In this case (PEAK) should reduce a ratio.
Detect area positions
4
6 5
2
1 3
7 8 9
Select ALC mode
[AVE, AREA, PEAK/AVE]
Peak level / Average level
[0/100, 15/85, 30/70,
50/50, 75/25, 100/0]
Video level adjustment
(*)
[-128～000～+127]
Return(Return to the main menu)
End(Return to the normal screen)
(*)Press the Set button;
the numerals flash. Press the Up
and Down buttons to change the
video level.