Box 2069 Bellingham, Wa 98227-2069 Email: manuals@grizzly.com functional Overview the Model g0679 stroke/Edge sander is used to sand large workpieces such as tabletops or doors. For maximum versatility, the belt assembly pivots from horizontal to vertical to allow for edge sanding.
G. sanding Belt h. table K. table travel lock M. Work stops N. dust Collection port O. drive Wheel Cover p. Belt tilt lever g0679 stroke/Edge sander identification figure 1. identification. idler Wheel Cover adjustable Foot table handle table Elevation handwheel...
Machine Data Sheet MACHINE DATA SHEET MODEL G0679 STROKE/EDGE SANDER Product Dimensions: Shipping Dimensions: Electrical: Motor: Main Specifications: Table Information Model G0679 Page 1 of 2 g0679 stroke/Edge sander...
Page 7
Belt Information Platen Information Construction Other Related Information Other Specifications: Features: Model G0679 g0679 stroke/Edge sander Page 2 of 2...
Minimum Circuit size ...30 amps g0679 stroke/Edge sander power connection Device the type of plug required to connect your machine to power depends on the type of service you cur- rently have or plan to install.
Otherwise, filing a freight claim can be difficult. When you are completely satisfied with the condi- tion of your shipment, inventory the contents. g0679 stroke/Edge sander...
11. Minimum working clearances. 47" 115" children and visitors may be seriously injured if unsuper- vised around this machine. Lock entrances to the shop or disable start switch or power connection to prevent unsupervised use. g0679 stroke/Edge sander...
Cross Brace figure 12. Cross brace attachment. Connect a second cross brace in the same manner. g0679 stroke/Edge sander attach the other upright to the two cross brac- es with (8) in figure 13. have an assistant stabilize the upright assembly during fastening. do not yet fully tighten the bolts.
Page 18
"-13 lock nut, then inserting the lock handle through the bracket slot and into the threaded hole, as shown in figure 18. platen lock Knob and Flat Washer pivot Bolt & lock nut figure 18. Lock bracket. g0679 stroke/Edge sander...
Page 19
(4) bolts, as shown in figure 20. platen assembly Frame Flange Bolts idler Wheel assembly figure 20. Idler wheel assembly. g0679 stroke/Edge sander 11. secure the idler wheel box to the platen ⁄ -20 x ⁄ assembly with (2) ⁄...
Page 20
26. upright ⁄ " cap screws and ⁄ " flat washers Cap screw figure 25. Table mounting. ⁄ -20 x ⁄ " phillips head phillips head screws rear Cover figure 26. Rear cover. g0679 stroke/Edge sander...
Page 21
28. platen press slide Counterweight platen press figure 28. Platen press and counterweight. g0679 stroke/Edge sander 19. slide the larger handwheel on the elevation ⁄ -20 x ⁄ "...
Dust collection DO NOT operate the Model G0679 without an adequate dust collection system. This sand- er creates substantial amounts of wood dust while operating. failure to use a dust collec- tion system can result in short and long-term respiratory illness.
OMMEND that you read books, trade maga- zines, or get formal training before begin- ning any projects. Regardless of the con- tent in this section, Grizzly industrial will not be held liable for accidents caused by lack of training. -22- basic controls use figures 35–36 and the descriptions below...
36. Basic controls (continued). g0679 stroke/Edge sander Table Movement the table on the Model g0679 can be moved both vertically and horizontally. vertical Table Movement Vertical movement is used to accommodate workpieces of different thicknesses and once set for a specific workpiece, doesn't need to be changed.
When the sander is in edge sanding mode, the work stops must be placed on the right side of the machine. The belt speed on the Model G0679 is 3600 fpM, or over 40 Mph. A workpiece ejected at this speed could cause serious personal injury and property damage.
Stroke/Edge Sander conversion For maximum versatility, the Model g0679 func- tions both as a stroke sander and an edge sander. Conversion from one to the other takes only a few minutes and requires removing the platen press...
Page 28
11. position the table workstop on the right side of the table and the auxiliary work stops on the right side of the base. g0679 stroke/Edge sander table Even With Belt...
Replacement replacing the sanding belt on the Model g0679 is a simple process and is performed when the sanding belt becomes worn or when a sanding belt of a different grit is desired. To replace the sanding belt: disConnECt sandEr FroM poWEr! use the belt tension handwheel to release tension from the belt.
Movement a stroke sander is unique in that it uses a movable platen to apply sanding pressure to the workpiece. this allows a user to vary the amount of material removed over different areas of the workpiece. the platen press moves in two different planes.
Compatible with safety glasses! figure 50. half-mask respirator with disposable cartridge filters. g0679 stroke/Edge sander pRO-STicK Abrasive Surface cleaners ® Extend the life of your sanding discs and sleeves! Choose the pro-stick control or without a handle for more usable area.
Every 500 hours: • refill table elevation gearbox. cleaning Cleaning the Model g0679 is relatively easy. Vacuum sawdust, and wipe off the remaining dust with a dry cloth. if any resin has built up, use a resin dissolving cleaner to remove it.
2. Motor mount loose/broken/incorrect. 3. Motor fan is rubbing on fan cover. 4. Motor bearings are at fault. g0679 stroke/Edge sander Troubleshooting possible solution 1. Ensure power supply is switched on; ensure power supply has the correct voltage.
Page 36
3. do not keep platen press/workpiece in one place for too long. 1. dry stock properly before sanding. 2. use different stock. or, accept the characteristics of the stock and plan on cleaning/replacing belts frequent- 1. adjust belt tracking (page 36). g0679 stroke/Edge sander...
90° Stop the Model g0679 is equipped with an adjustable 90° stop to ensure that the belt is perpendicular to the table when converted to the edge sanding mode. if the belt is not 90° to the table, this stop can be adjusted.
-36- belt Tracking the sanding belt tracking on the Model g0679 can be adjusted to make sure the belt travels smoothly between the drive and idler wheels with- out rubbing on the sides of the platen assembly.
FroM poWEr! loosen the jam nut shown in (figure 62). Jam nut figure 62. Wear pin adjustment. g0679 stroke/Edge sander tighten the hex bolt until you just begin to feel resistance. —the goal is to position the wear pins against the ways without applying pressure to the them.
EXpERiENciNG DifficuLTiES. if you are experiencing difficulties understanding the information included in this section, contact our technical support at (570) 546-9663. g0679 stroke/Edge sander...
View this page in color at www.grizzly.com. 220 VAC L6-30 PLUG (as recommended) figure 63. Switch wiring. g0679 stroke/Edge sander Wiring Diagram READ ELECTRICAL SAFETY WARNING! SHOCK HAZARD! Disconnect power before working on wiring. figure 64. Motor wiring. ON PAGE 38!
HEX BOLT 1/4-20 X 1/2 P0679028 COVER SPINDLE P0679029 TUBE CAP PSW03-1 KNOB 5/16-18 X 3/4 P0679031 LEVER KNOB 1/2-12 P0679032 LEVER g0679 stroke/Edge sander Main parts List REF PART # P0679034 PLN06 P0679036 PWR1214 37-1 PWR1719 PAW04M PAW05M PAW06M...
MuST maintain the original location and readability of the labels on the machine. if any label is removed or becomes unreadable, REpLAcE that label before using the machine again. contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels. -50-...