Page 2
WARNING Some dust created by power sanding, sawing, grinding, drilling, and other construction activi- ties contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: • Lead from lead-based paints. •...
Page 5
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubri- cating and changing accessories. G0529 Oscillating Spindle & Disc Sander 15. USE RECOMMENDED ACCESSORIES. 16. REDUCE THE RISK OF UNINTENTION- 17. CHECK DAMAGED PARTS. Before fur-...
Page 6
• TEST RUN THE MACHINE before starting any work. Always wear a respira- tor when operating the Model G0529. Using this machine produces saw- dust which may cause allergic reactions or res- piratory problems. G0529 Oscillating Spindle & Disc Sander...
Grizzly’s com- mitment to customer satisfaction. We are pleased to provide this manual with the Model G0529. It was written to guide you through assembly, review safety considerations, and cover general operating procedures. It represents our effort to produce the best documentation pos- sible.
SECTION 3: CIRCUIT REQUIREMENTS 110 Volt Amperage Draw The Model G0529 1 HP motor is wired to operate at 110V and will draw the following load: Motor Load...10 Amps Plug Type The Model G0529 is supplied with a NEMA 5-15 plug.
NOTICE The wire on the power cord with green or green and yellow striped insulation is the grounding conductor. G0529 Oscillating Spindle & Disc Sander Extension Cords 110V Operation If you find it necessary to use an extension cord at 110V: •...
An important part of safety is knowing your machine and its components. Take the time to familiarize yourself with the features of your new G0529 Oscillating Spindle & 12" Disc Sander. They will be fre- quently mentioned throughout the instructions in this manual.
SECTION 5: SET UP Unpacking The Model G0529 Oscillating Spindle & 12" Disc Sander was carefully packed at the factory. If you discover the machine is damaged after you have signed for delivery, and the truck and driver are gone, you will need to file a freight claim with the carrier.
G0529 Oscillating Spindle & Disc Sander Site Considerations Weight Load The Model G0529 weighs 143 lbs. and has a " X 16 " footprint. Most shop floors should be sufficient to carry the weight of the machine.
Sharp edges on metal parts may cause person- al injury. Examine the edges of all metal parts before handling. -12- The Model G0529 Sander mounts on a sturdy cabinet stand. To assemble the cabinet stand: caught loose clothing completed...
⁄ " flat washers combination as shown in Figure 5. Figure 5. Cabinet hole location. G0529 Oscillating Spindle & Disc Sander Installing Spindle To install the spindle onto the sander: Disconnect the machine from the power supply. Select the proper diameter of spindle sleeve.
90˚ from the edge of the sanding sleeve as shown in Figure 9. Adjust the pointer to 90˚. Figure 9. Squaring the table and spindle. G0529 Oscillating Spindle & Disc Sander...
Spin the disc by hand to check if the sand- paper is touching the table. Note—DO NOT turn the disc sander on at this point. Repeat steps 1-3 if the sandpaper touches table at any point in the rotation. G0529 Oscillating Spindle & Disc Sander ⁄ '' gap...
0˚ mark on the scale. Retighten the setscrew that secures the angle pointer. G0529 Oscillating Spindle & Disc Sander Dust Collection There are two 2" dust collection ports for the sander that should be connected to a dust collec- tor.
Be certain the safety glass- es you wear meet the appropriate stan- dards of the American National Standards Institute (ANSI). -18- The Model G0529 sander is equipped with a pad- dle-type power switch with a safety key. To operate the power switch: loose clothing...
Spindle Sanding The oscillating spindle sander on the Model G0529 produces an extremely fine sanding finish on edges or contours. The oscillation of the spin- dle disperses the material contact throughout the sanding sleeve to prevent burning. To perform spindle sanding operations:...
(Figure 19). Note—The miter gauge can be used in either direction in the slot to achieve the proper relation of the workpiece to the disc. Figure 19. Disc sanding with miter. G0529 Oscillating Spindle & Disc Sander...
DO NOT connect the machine to the power source while performing any maintenance on this machine. G0529 Oscillating Spindle & Disc Sander Check for the following conditions before you use the sander: • Loose table bolts. • Worn or damaged sanding discs or sleeves.
(570) 546-9663. Trained service technicians will be glad to help you. If you have any comments regarding this manual, please write to Grizzly at the address below: Grizzly Industrial, Inc. Technical Documentation P.O. Box 2069...
2. Starting the workpiece on a leading cor- ner. G0529 Oscillating Spindle & Disc Sander CORRECTION 1. Store sanding sleeve/disc away from extremely hot or dry tem- peratures. 2. Store sanding sleeve/disc flat not bent or folded.
Warranty & Returns Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Page 33
Do you think your purchase represents good value? ___Yes Would you recommend Grizzly Industrial to a friend? ___Yes Would you allow us to use your name as a reference for Grizzly customers in your area? Note: We never use names more than three times. ___Yes Comments:_________________________________________________...
Page 34
FOLD ALONG DOTTED LINE FOLD ALONG DOTTED LINE Send a Grizzly Catalog to a friend: Name_______________________________ Street_______________________________ City______________State______Zip______ GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Place Stamp Here...
Page 36
Buy Direct and Save with Grizzly Visit Our Website Today And Discover Why • • • ® – Trusted, Proven and a Great Value! Grizzly ® Is The Industry Leader! SECURE ORDERING ORDERS SHIPPED WITHIN 24 HOURS E-MAIL RESPONSE WITHIN ONE HOUR...