Lanier AP4510 Setup Manual page 423

Maintenance Kit Type 4510
REPLACEMENT GUIDE
The maintenance kit contains the parts required to maintain the printer. When "Change Maint.Kit"
appears on the panel display, replace the parts included in the maintenance kit. Read this guide
carefully before you use the maintenance kit.
For safety purposes, carefully follow the instructions in this guide.
CHECKING THE CONTENTS OF THE
CAUTION
BOX
The inside of the machine becomes very hot. Do not touch the parts
with a label indicating a "hot surface". Touching a "hot surface"
could result in a burn injury.
The maintenance kit is composed of 2 types of boxes,
Disposal should take place at an authorized dealer or appropriate
Type 4510A and Type 4510B. Each box contains the
collection site.
following parts. Confirm that the contents of the boxes
If you dispose of the used parts yourself, dispose of them according
match the following lists.
to local regulations.
Type 4510A
Replacement Guide (this sheet)
Removing the Development Unit from the Box
Development Unit
TURNING OFF THE PRINTER
Turn the printer's power switch off.
Disposal Bag
Important For packing the used Development Unit
The inside of the machine becomes very hot. Be sure to turn
off the printer before attempting to replace any of the parts.
Type 4510B
When replacing the old fusing unit with a new one, turn off
the printer and wait for about 30 minutes before beginning
Fusing Unit
the installation.
On
Transfer Unit
O ff
Gloves
Disposal Bag
For packing the used Transfer Unit
Brief reference sheet
If one or more of the items are missing, please contact your sales
or service representative.
< G790-8610 >
You should replace all the parts included in the
maintenance kit at the same time. Be sure to replace them
in the following order:
ZFCM010J
1. Transfer Unit
2. Development Unit
3. Fusing Unit
ZFCM020J
TAPM660E
TAPM241E
REPLACING THE TRANSFER UNIT
Hold both sides of the unit. Lift the side of the unit closest
to you slightly ( ), and remove the unit from the printer
WARNING
( ) as shown in the illustration. Put the used transfer unit
Do not incinerate the used transfer unit. Toner dust might ignite
in the disposal bag.
when exposed to an open flame.
Disposal should take place at an authorized dealer or appropriate
collection site.
If you dispose of the used parts yourself, dispose of them according
to local regulations.
Open the bypass tray ( ), and then open the duplex unit
by pushing the catch upwards ( ).
Important
After removing the transfer unit, put the unit in the disposal
bag. Be careful not to tilt or shake the unit. Otherwise, toner
might scatter.
Take the new transfer unit out of the Type 4500B box, and
remove the plastic bag.
Open the right cover by pushing the catch upwards.
Take the desiccant out.
There is an arrow sticker in the bottom right side of the
cover, which is pointing to the shaft. Align the new transfer
unit with the shaft ( ), and then slide the unit in place
( ).
Put onthe gloves included in the Type 4500B box.
Be sure to wear the gloves to avoid getting your hands dirty or
damaging the belt surface of the new transfer unit.
While pressing down on the corner of the transfer unit
indicated by the arrow ( ), return the green lever ( ) to
TAPM310E
its original position to lock the transfer unit in place.
Raise the green lever ( ) inside the right cover to release
the transfer unit.
Note
TAPM010E
If you cannot return the green lever to its original position,
raise the green lever and remove the transfer unit. After that,
try to install the transfer unit again.
Leave the right cover open, and go to "
DEVELOPMENT UNIT".
REPLACING THE DEVELOPMENT
UNIT
WARNING
Do not incinerate the used development unit. Toner dust might ignite
when exposed to an open flame.
Disposal should take place at an authorized dealer or appropriate
collection site.
If you dispose of the used parts yourself, dispose of them according
to local regulations.
Open the front cover.
While raising the green lever inside the front cover ( ),
and then slide the development unit out about 10cm (4").
ZFCM050E
Slide the development unit out far enough so that you can
hold it by the handle ( ).
Important
Slide the unit out to the position shown in the following
illustration. If you slide it out too far, it may fall and damage
the front cover.
TAPM030E
ZFCM040E
TAPM040E
REPLACING THE