Telco Disarm Sequence; Turning Outputs On/Off; Reset Latching Outputs; Codepad Id/Buzzer Tone Change - Bosch ICP-CC404 User Manual

ICP-CC404 | User's Guide | 13.0
Call Forward – Immediate On
You can redirect calls to anywhere in Australia,
including mobile phones, pagers, and answering
services. When Call Forward is turned on, your
telephone does not ring.
Call Forward – No Answer
If your telephone is not answered within 20 sec, this
feature redirects all incoming calls to another number
anywhere in Australia. When this feature is enabled,
you can still make outgoing calls.
Table 10: Telco Arm/Disarm Dialing Digits
Digit Number to
Required Program
0 0
1 1
2 2
3 3
4 4
5 5
6 6
7 7
To program the Telco Arm Sequence:
1. Enter your four-character Master Code and press
[3 #] (for example, [2 5 8 0 3 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Press [1 #] to select the Telco Arm Sequence.
Three beeps sound.
3. Enter the call forward sequence (for example,
[* 6 1][Phone Number][#] to program the Call
Forward - No Answer sequence, or [* 2 1][Phone
Number][#] to program the Call Forward
Immediate sequence).
To program a "*" in the Telco Arm Sequence,
enter [* 1]. To program a "#" in the Telco Arm
Sequence, enter [* 2].
4. Press [#] when finished.
Two beeps sound, and the STAY and AWAY
indicators turn off.
To disable the Telco Arm Sequence,
enter the call forward sequence as [* 4]
(break) for Step 3.
12.2

Telco Disarm Sequence

This feature automatically disables the call forward
sequence when disarming the system.
To program the Telco Disarm Sequence:
1. Enter your four-character Master Code and press
[3 #] (for example, [2 5 8 0 3 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
12

Turning Outputs On/Off

Digit Number to
Required Program
8 8
9 9
* *1
# *2
4-sec pause *3
break *4
2. Press [2 #] to select the Telco Disarm Sequence.
Three beeps sound.
3. Enter the call forward disable sequence (for
example, [# 6 1 #] to disable the No Answer
Call Forward sequence, or [# 2 1 #] to disable
the Call Forward Immediate sequence).
To program a "#" in the Telco Disarm
Sequence, enter [* 2].
4. Press [#] when finished.
Two beeps sound, and the STAY and AWAY
indicators turn off.
To disable the Telco Disarm Sequence,
enter the call forward sequence as [* 4]
(break) for Step 3.
13.0 Turning Outputs On/Off
This feature only applies if your installer set up an
output to be turned on or off by the codepad. Your
installer can program up to three outputs to control a
pool pump, outside lighting, and so on.
To turn an output on or off:
1. Enter your Master Code and press [5 #] (for
example, [2 5 8 0 5 #]).
Three beeps sound and the STAY and AWAY
indicators flash.
2. Enter the output number (1 to 3) you want to
turn on or off.
3. Press [#] to turn the output on, or press [*] to
turn the output off.
Three beeps sound if you turn the output on,
and two beeps sound if you turn the output off.
Repeat Step 2 and Step 3 to turn other outputs on
or off.
4. Press [#] to exit from this function.
Two beeps sound and the STAY and AWAY
indicators turn off.

14.0 Reset Latching Outputs

This feature only applies if your installer
programmed an output to latch (remain on) until you
acknowledge the event that turned on the output.
To reset latching outputs:
Hold down [7] until two beeps sound. The output
resets.
15.0 Codepad ID/Buzzer Tone
Change
Hold down [8] continuously to change the tone of
the codepad buzzer.
There are 50 different tones, from 1500 Hz to
5000 Hz. If multiple codepads are installed, each
codepad can sound a different tone.
Bosch Security Systems, Inc. | 10/08 | F01U089400-01