Hdmi Mode Setting; Setting The Auto Delay; About Hdmi - Pioneer LX01 Operating Instructions Manual

Other connections
1 Use the supplied HDMI cable to connect the HDMI
IN 2 to 3 interconnect on this receiver subwoofer to
an HDMI output on your HDMI component.
Once this receiver subwoofer is properly connected to
your HDMI component, the HDMI indicator (red) lights
up on the display unit when you watch HDMI contents.
2 Use the supplied HDMI cable to connect the HDMI
OUT interconnect on this receiver subwoofer to an
HDMI interconnect on a HDMI-compatible display.
• The arrow on the cable connector body should be
face down for correct alignment with the connector
on the unit.
3 Use the HDMI 2 to 3 button to select the HDMI
input you've connected to.
The remote control switches to the BD control mode when
HDMI 2 is pressed, the DVD control mode when HDMI 3
is pressed. If you do not want to operate these
components, press the SYSTEM CONTROL button to set
the remote control to the receiver control mode.
You can also use the display unit INPUT SELECTOR to
carry out this operation.
• Set the HDMI Mode in HDMI mode setting below to
Through Mode if you want to hear HDMI audio
output from your TV or Flat Screen TV (no sound will
be heard from this receiver).
• If the video signal does not appear on your TV or Flat
Screen TV, try adjusting the resolution settings on
your component or display.

HDMI mode setting

Specifies the routing of the HDMI audio signal out of this
receiver subwoofer (amp) or through to a TV or Flat
Screen TV. You cannot use a number of sound functions
of this unit when HDMI Mode is set to Through Mode.
1 Press SETUP.
SETUP
ENTER
2 Select 'HDMI Setup' then press ENTER.
ENTER
3 Select 'HDMI Mode', then press ENTER.
ENTER
4 Adjust the setting then press ENTER to
confirm.
• AMP Mode – Output an HDMI audio signal from this
unit.
• Through Mode – Output an HDMI audio signal from
a TV or Flat Screen TV.
The HDMI THROUGH indicator lights.

Setting the Auto Delay

This feature automatically corrects the audio-to-video
delay between components connected with an HDMI
cable. The audio delay time is set depending on the
operational status of the display connected with an HDMI
cable. The audio delay time is automatically adjusted
according to the video delay time.
1 Press SETUP.
SETUP
ENTER
2 Select 'HDMI Setup' then press ENTER.
ENTER
3 Select 'Auto Delay', then press ENTER.
ENTER
4 Select 'A.Delay On' or 'A.Delay Off' then
press ENTER to confirm.
Tip
• This feature is only available when the connected
display supports the automatic audio/video
synchronizing capability ('lip-sync') for HDMI or
HDMI Control. If you find the automatically set delay
time unsuitable, set A.Delay to Off and adjust the
sound delay settings manually (page 34).

About HDMI

HDMI (High-Definition Multimedia Interface) supports
both video and audio on a single digital connection for
use with DVD players, DTV, set-top boxes, and other AV
devices. HDMI was developed to provide the
technologies of High-bandwidth Digital Content
Protection (HDCP) as well as Digital Visual Interface
(DVI) in one specification. HDCP is used to protect digital
content transmitted and received by DVI-compliant
displays.
HDMI has the capability to support standard, enhanced,
or high-definition video plus standard to multichannel
surround-sound audio. HDMI features include
uncompressed digital video, a bandwidth of up to 2.2
gigabytes per second (with HDTV signals), one connector
(instead of several cables and connectors), and
communication between the AV source and AV devices
such as DTVs.
HDMI, the HDMI logo and High-Definition Multimedia
Interface are trademarks or registered trademarks of HDMI
Licensing, LLC.
08
43
En