Control Terminals (Control) - Sanyo DSR-3716 Instruction Manual

Names and functions of parts (rear panel)

Control terminals (CONTROL)

This DVR can be remotely controlled when a remote-control circuit (R1, R2, C) similar to that shown below is connected to the
remote-control terminals.
• Use a resistance of 1/10 ohms or more and with a D ranking (Precision within ±0.5%).
• The remote control cable should be no more than 5 m long.
* The DSR-3709 can operate up to nine cameras (*).
1
IN
OUT
ALL
RESET
R1
(When operated (When combined
independently) with R2 Shift key)
SW 1 : Camera 1*: ALARM +
SW 2
: Camera 2*: ALARM –
SW 3 : Camera 3*: AUTO FOCUS
SW 4 : Camera 4*: SEQUENCE
SW 5 : Camera 5*: MON2
SW 6 : Camera 6*: PLUS
SW 7 : Camera 7*: QUAD
SW 8 : Camera 8*: MULTI
SW 9 : Camera 9*: MENU RESET
SW 10 : Camera 10:
SW 11 : Camera 11: PAN left
SW 12 : Camera 12: PAN right
SW 13 : Camera 13: TILT down
SW 14 : Camera 14: TILT up
SW 15 : Camera 15: ZOOM wide
SW 16 : Camera 16: ZOOM tele
b Model DSR-3709 (rear panel)
1
IN
OUT
ALL
RESET
2 3 4 5 6 7 8 9
AUDIO MONITOR OUT
MAIN MON2
IN OUT MIC IN USB
REMOTE
C
R2
SW 17 : REC/STOP
SW 18
: PLAY/STOP
: STILL
SW 19
: SEARCH
SW 20
: SHIFT (Doubles with R1)
SW 21
SW 22 : PLAY
: REC
SW 23
: MENU
SW 24
: EXIT/OSD
SW 25
SW 26 : +
SW 27 : –
: →
SW 28
: ←
SW 29
: ZOOM
SW 30
SW 31 : COPY
SW 32 : TIMER REC
2 3 4 5 6 7 8 9
AUDIO MONITOR OUT
MAIN MON2
IN OUT MIC IN USB
ALARM IN
C 1 2 3
10 11 12 13 14 15 16
C 1 2 3
A RS-485 B
LAN RS-485 SENSOR
TERMINATE
ALARM OUT
OFF ON
DO NOT CONNECT TO PHONE LINE
R1 R2
Pin
C
REMOTE R1
REMOTE R2
CLOCK IN
CLOCK OUT
ALARM OUT
ALARM RESET
WARNING OUT
FULL
ALARM FULL
SERIES IN
SERIES OUT
EXT TIMER IN
NON REC OUT
C
ALARM IN
C 1 2 3
C 1 2 3
A RS-485 B
LAN RS-485 SENSOR
TERMINATE ALARM OUT
OFF ON
DO NOT CONNECT TO PHONE LINE
AC IN
4 5 6 7 8 9 10 11 12 13 14 15 16
4 5 6 7 8 9 10 11 12 13 14 15 16
REMOTE
C R1 R2 C
CONTROL
C
Signal
Ground
Remote input 1
Remote input 2
Input of a clock setting signal from an external
device
Output of a clock setting signal to an external
device
Total alarm output
Alarm reset input
Output of an HDD malfunction error
Capacity warning output for normal recording
area space
Capacity warning output for alarm recording area
space
Signal input from an analog series connection
Signal output to an analog series connection
Signal input from an external timer
Recording stopped output
Ground
AC IN
4 5 6 7 8 9
4 5 6 7 8 9
REMOTE
C R1 R2 C
CONTROL
Foreword 12