OWNER'S MANUAL Network Camera & Network Video Server Please read this manual carefully before operating your set and retain it for future reference. MODEL LSW900/LSW901 series LSW2010 series LNP3700T series LVW900/LVW901 series LDW2010 series LNP2800(I) series LVW700/LVW701 series LVS201 series LVS301/LVS311 series LW9226(I)/LW9228(I) series 1206 (V1.1)
LNP3700T/LNP2800/LNP2800I series) ........35 LG Smart Web Viewer Overview ..............6 Auto Tracking ..................39 Configuration menu overview...............7 General operation ................40 Configuring the LG Network Camera Device ........8 Camera menu settings..............40 Accessing the Configuration menu ..........8 PAN/TILT Settings ................46 System settings..................8 OSD Settings ..................48 Audio &...
Introduction The LG Network Camera is designed to use on an Ethernet network and must be assigned an IP address to make it accessible. This manual contains instructions on how to install and manage the LG Network Camera in your networking environment. Some knowledge of networking environments would be beneficial to the reader.
The LG Ipsolute VMS and the LG Smart Web Viewer program are Web Browser version 6.0 and below the version 8.0. the network program of the LG Video Server and the LG IP cameras. • To view streaming video in Internet Explorer, set your browser DirectX DirectX 9.0 or above...
IP address, Model name and so on. 3.1 Start your Web browser. Note: 3.2 Enter the IP address of the LG IP device in the address The computer running the IP Utility must be on the same net- bar of the browse.
LG Smart Web Viewer Overview Click to save the current image in JPEG format on your computer. 1. Click the [Snapshot] button and then the Snapshot window is displayed. 2. Click the [Save] button in the Snapshot window. 3. Enter the file name (JPEG format) and select the folder to save it.
System Maintenance Log & Report Displays the current surveillance live screen. You can monitor the camera image Language on the live view window of the LG Smart Camera Web Viewer. Stream Click this button to connect or disconnect Audio Option Audio &...
Displays the current version of Firmware, Hardware, Software and Web Client. Option Configuring the LG Network Camera Device The features and options of the LG IP camera are configured through the Configuration menu. Only administrator-level users have permission to access the Configuration menu.
Maintenance Time zone Set the time difference from GMT in the area where the IP device is installed. Select the time zone in the area where the IP device is installed from the drop down list. Time mode > Synchronize with NTP Server: Select if you want to synchronize the IP device’s date and time with those of the time server called NTP (Network Time Protocol).
Log & Report Notes: • Backup and Restore can happen on IP device having the same version of firmware. This feature is not intended for multi-configurations or for firmware upgrades. • [Backup] function is allowed in HTTP protocol but not in HTTPS protocol.
Language Audio & Video settings Camera Language list Select a language for the LG Smart Web Viewer configuration menu and information display. • Save: Click this button to confirm the settings. Preview You can preview the camera image on the preview window.
Stream > Bit rate: If the [Quality] option set to CBR, this option is displayed. Edit the bit rate value from 256 kbps to 10 240 kbps. Note: If the ‘Bit rate’ is configured too low with high resolution, the actual frame rate will decrease because of narrow bandwidth.
0 to 127. > Zoom speed: Enter the zoom speed of the PTZ device to view the object close or at a distance. Default value for the LG Multix protocol is 1 and ranges from 0 to 3. > Focus speed: Enter the focus speed of the PTZ device to focus an object clearly near or far.
Preset (Option) 4. Click the [Save] button to confirm the settings. Pattern You can activate the camera in a repeating pattern. The pattern is programmed by recording your manual pan, tilt, and zoom operations. The camera stores the movements you performed in memory. >...
> Zoom speed: Enter the zoom speed of the PTZ device to view [Preset tour]. the object close or at a distance. Default value for the LG Multix protocol is 1 and ranges from 0 to 3. > Focus speed: Enter the focus speed of the PTZ device to focus an object clearly near or far.
Preset 1. Move the camera to the point you want by using the arrow buttons. (LW9228/LW9226/LW9228I/LW9226I/LNP3700T/LNP2800/ 2. Adjust the zoom, focus or iris options. LNP2800I models only) 3. Set the Pan, Tilt, Zoom or Focus speed options. Note: 4. Click the [Save] button to confirm the settings. While configuring PATTERN/PRESET/GROUP TOUR/AUTO PAN, turn off Auto Tracking feature temporarily.
3. Click the [Add] button. » To remove the preset index from the group 4. Repeat the steps 1 to 3 to add other positions. 1. Enter the group number in the [Group index] option. » To remove the preset position 2.
Motion detect How to set the motion detect window 1. Click the [Add] button. The motion detect window is displayed. You can add the five windows maximum for motion detection area. 2. Set the [Sensitivity] option. 3. Click the edge or corner of the window box to adjust the window size for motion detection.
Network settings ARP Ping > Enable ARP Ping to configure IP address: Check to enable ARP Basic ping. • Save: Click this button to confirm the settings. RTP stream RTP (Real-time Transport Protocol) is an internet protocol that allows programs to manage the real-time transmission of multimedia data, via unicast or multicast.
TCP/IP > RTP multicast: When enabled it reduces the transmission load on the camera by making the computer of the same segment network receive the same transmission data. When multicast option is checked then select Video Port number, Audio Port number and Data port number.
Gateway: Enter the gateway address. DNS server status This free service is very useful when combined with the LG DDNS Server. It allows the user to connect the IP device using the URL, rather > Primary DNS server: Enter the Primary domain name server that than an IP Address.
IP filtering Deny all: Deny all the IP address basically, but the IP addresses in the list are allowed. It needs at least one IP The access of the IP addresses in the list are allowed or denied address to activate this function. according to the choice made in the drop-down list of the Basic policy option.
User settings • Remove: Click this button to delete the IPv6 address. 1. Select the alias from the list. Basic 2. Click the [Remove] button. The IPv6 address will be deleted. The IP device is shipped with the login rights of administrator only. If others need to access the IP device excluding the configuration a login SNMP with viewer rights need to be created.
4. Select the authority from the drop down list to provide the Anonymous access rights to each user and then click the [Save] to con- > Enable anonymous login firm your selection. Check the box to enable anonymous user login - allows the Administrator: Allows you to operate setup menus and user access for only viewing the live stream image.
Event settings Event schedule list > To edit the Event Schedule Event schedule 1. Select the Trigger event and click the [Edit] button. Event When an event (VA/ Motion detect/ Sensor Event) occurs, this unit schedule window is displayed. records the live images and routes as configured. The event function is 2.
Event Server Folder: Type the path with the folder that is shared in the FTP server. Event Servers are used to receive the recorded video clip and/or notification messages. Test: Select [Test] to test the FTP server. 3. Click the [Save] button to confirm the settings. >...
Sensor & Relay (Option) User ID: Enter the user ID of the SMTP server. This would be the one who owns the mail account. Password: Enter the password of the SMTP server. Address: Enter the SMTP server address. Port: Enter the port number. The default port is 25. Enable SSL: Check when use the SSL (Secure Socket Layer) protocol.
Fan (Option) OSD Menu Setup (LSW900/LSW901/ LVW700/LVW701/LVW900/LVW901/ LDW2010/LSW2010 series) The following table shows the list of menu items and options. These options are depending on models. The OSD images are different from each model. Main Menu Sub Menu Contents Fan fail notification EXPOSURE ELC/ALC WDR/BLC...
MANUAL COLOR TEMP INDOOR, SPECIAL D-ZOOM OUTDOOR ZOOM -100 to 100 BLUE -100 to 100 TILT EXIT RET/TOP/END EXIT DAY/NIGHT AUTO LEVEL LOW/ MIDDLE/ D-EFFECT OFF/ V-FLIP/ MIRROR/ ROTATE HIGH SHARPNESS 0 to 68 DWELL TIME 5, 10, 15, 30, 60 COLOR OFF/ ON EXIT...
General Operation Notes: • button: Used to move upper direction on the menu screen. 1. Click the [OSD control] button on the LG Smart Web Viewer. • button: Used to move lower direction on the menu screen. 2. Click button on the OSD control window.
WDR/BLC (Option) BRIGHTNESS Use Backlight option to view the object clearly in backlight conditions. You can increase the brightness of the darkened video. If you set the brightness to lower value, the image gets darkened. If you set the 1. Select [WDR/BLC] option on the [EXPOSURE] menu. brightness to higher value, the image gets bright.
Note: > COLOR TEMP: Use button to select a function. If you set to one of the SHUTTER options except AUTO on the > INDOOR: The color temperature range for the proper white [SHUTTER] menu or [AGC] to [OFF], the [SENS-UP] setting is not balance is approximately 3 200 K.
Privacy setting • NIGHT: Black-and-white mode enabled. This function is aiming at the protection of personal privacy. The 3D-DNR setting selected part is not displayed on the screen. 1. Select the [PRIVACY] option. 1. Select [3D-DNR] option. 2. Use button to select [ON] and press .
Note: D-EFFECT (Digital effect) The parts with the registered mask numbers from AREA1 to AREA4 You can select the digital effect. have the same color. (So do the parts with the numbers from AREA5 to 1. Select the [D-EFFECT] option on the [SPECIAL] menu. AREA8.) If you change the mask color, the registered mask color will be 2.
Reset setting • OFF: To display the picture with grayscale. USER TITLE You can use the camera identification to assign a number and character to the camera. To disappear the user title, select [OFF]. 1. Select the [USER TITLE] option on the [SPECIAL] screen. 2.
OSD Menu Setup (LW9226/LW9228/ CAMERA SET LW9228I/ LW9226I/LNP3700T/ AUTO LNP2800/LNP2800I series) INDOOR/ COLOR TEMP OUTDOOR The following table shows the list of menu items and options. WHITE BALANCE - 100 to +100 MANUAL LW9226/LW9228/LW9226I/LW9228I series BLUE - 100 to +100 1st level 2nd level 3rd level...
PAN/TILT SET MASK NUMBER 1 to 8 USER TITLE ON/OFF SET MASK ZOOM MAG ON/OFF MASK STATE ON/OFF OSD SET FUNCTION ON/OFF GRAY, WHITE, DOME ID ON/OFF PRIVACY MASK MASK COLOR BLACK RETURN WIDTH 2 to 320 LANGUAGE The option depends on the model. HEIGHT 3 to 240 INFORMATION...
LNP3700T/LNP2800/LNP2800I series CAMERA SET AUTO 1st level 2nd level 3rd level Contents INDOOR/ COLOR TEMP AUTO/MANUAL/ONE PUSH/ OUTDOOR CAMERA SET FOCUS MODE ZOOM TRIG WHITE BALANCE - 100 to 100 MANUAL FOCUS DIST 1M, 3 M, 6 M BLUE - 100 to 100 LNP3700T series: x1 to x36 FOCUS ZOOM START...
PAN/TILT SET MASK NUMBER 1 to 8 USER TITLE ON/OFF SET MASK ZOOM MAG ON/OFF MASK STATE ON/OFF OSD SET FUNCTION ON/OFF PRIVACY MASK MASK COLOR GRAY, WHITE, BLACK DOME ID ON/OFF WIDTH 0 to 320 RETURN HEIGHT 0 to 240 LANGUAGE The option depends on the model.
Auto Tracking About Auto Tracking • The Auto Tracking is stopped when a user moves the camera (Pan/ Normal Scenario for Auto Tracking Tilt/Zoom) or turns on OSD Menu. It is started again whenever a Object detecting state user stops the control. The camera starts to search a moving object.
General operation Camera menu settings 1. Click the [OSD control] button on the LG Smart Web Viewer. Focus setting 2. Click button. The camera adjusts the focus automatically by sensing the center of the picture. The camera setting menu appears on the live view window.
Focus mode Exposure settings Select [FOCUS MODE] option on the [FOCUS] menu, then select the following mode. • AUTO: Auto-focus is activated automatically. • MANUAL: Focus is activated automatically after the zoom movement is finished. If you want to control the focus manually, press the FOCUS ( ) buttons on the controller.
AGC (Automatic Gain Control) setting SHUTTER (Shutter Speed) setting If the images are too dark, change the maximum Select the desired shutter speed for camera exposure. You can change [AGC] value to make the images bright. the shutter speed to higher speed to capture fast-moving subjects, though the image becomes darker.
White Balance setting objects, such as a blue sky or sunset. Select the method by which the camera shifts its output colors to When the scene is dim. compensate for the color of a light source. • ONE PUSH: If you select the ONE PUSH mode, you will be able to set up the White Balance automatically using button.
Day/Night setting 3D-DNR setting 1. Select [DAY/NIGHT] option on the [CAMERA SET] menu. 1. Select the [3D-DNR] option. If pictures are not clear due to brightness, use this function to reduce the noise of picture. 2. Use button to select the mode. 2.
Stabilizer setting (Option) 1. Select the [COLOR] option on the [CAMERA SET] menu. 2. Use button to change a color effect. The image stabilizer function minimizes the appearance of shaky images caused by low-frequency vibration. • ON: To display the picture with color. Select ON and press display the submenu.
PAN/TILT Settings 4. Select the [SET MASK] option and press button. 5. Select the mask zone using the PTZ control buttons and then press Privacy Mask setting button to save it. This function is aiming at the protection of personal privacy, the mask 6.
Special setting Home position The home position is the camera’s basic position. The camera returns to this position whenever you want. Use the following procedure to make the home position. 1. Select [HOME POSITION] option on the [SPECIAL] menu. 2. Use button to set it ON.
Auto return OSD Settings This function can be used to specify automatic return to a particular mode if a certain amount of time elapses without any operation being performed. 1. Select [AUTO RETURN] option on the [SPECIAL] menu. 2. Use button to set it [ON] and then press button.
FUNCTION setting 2. Use button to set it [ON]. Displays or removes the Function OSD on the screen. 3. Press button. The USER TITLE menu appears. 1. Select [FUNCTION] option on the [OSD] menu. 4. Use button to select a character, number, symbol 2.
RESET Setting Information You can view the current camera information such as PTZ software version, camera software version, camera ID, Protocol and Baud Rate. 1. Select [INFORMATION] option on the [RESET] menu. 2. Press button to display the current camera information. Initialization You can initialize the camera settings.
• IP Conflicts: If the LG network device is set with a static IP address and if the DHCP option is set then there may be IP’s same as the network device and other network partner. Hence set the static IP address to 0.0.0.0 to resolve this conflict.
After the factory settings login using the default user name and password. Video Streaming problems • If the video streaming does not start on the Web browser, install the LG Web Client ActiveX program on your computer following the instruc- tions on the Web browser. •...
• If we obtain lower frame rate than set we need to check from the system administrator for sufficient bandwidth available or reduce the num- ber of applications running on the client computer. • If the client PC’s are unable to access the multicast stream, check with the system administrator for the use of a valid multicast address or check if the router is supporting multicasting.
To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource. lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to email@example.com.
Specifications LSW900/LSW901/LVW700/LVW701/LVW900/LVW901/LSW2010/LDW2010 Series Item LSW900 LSW901 LVW700 LVW701 LVW900 LVW901 LSW2010 LDW2010 Image Device 6 mm (1/3 type) Super HAD II 6 mm (1/3 type) Vertical Double Interline CCD Lens Type Fixed Lens C/CS Mount Varifocal Lens (2.8 mm to 11 mm) C/CS Mount (F=3.7 mm) Video Out...
10/100 base TX Ethernet Protocol IPv4 and TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP IPv6 IPv4 FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG) IP support Dynamic, Static, Private IP Users Unicast 10 Streams / 50 user registration Operation Temperature / -30 ºC to 50 ºC /...
Power Source PoE, AC 24 V (±20 %) PoE, AC 24 V (±20 %) (1 A or above) (1.5 A or above) PoE, DC 12 V (±10 %) (1 A or above) DC 12 V (±10 %) (2 A or above) DC 12 V (±10 %) (3 A or above) Power Consumption...
IP support Dynamic, Static, Private IP Users Unicast 10 Streams / 50 user registration Operation Temperature / -10 ºC to 50 ºC / 0 % RH to 80 % RH Humidity Power Source PoE, DC 12 V (±20 %) (1 A or above) PoE, AC 24 V (±20 %) (1 A or above), DC 12 V (±10 %) (2 A or above) Power Consumption About 3 W...
LW9226/LW9226I/LW9228/LW9228I Series Item LW9226 LW9226I LW9228 LW9228I Camera Image Sensor 4.5 mm (1/4 type) EX-view HAD CCD x27 Zoom x37 Zoom Lens (F1.5 (Wide End), F3.8 (Tele End)) (F1.5(Wide End), F4.1(Tele End)) ( f = 3.25 mm to 88 mm ) ( f = 3.5 mm to 129 mm ) Resolution Up to 704 x 480, 704 x 576 (N/P)
Optical Zoom Panning Range & 0 ˚ to 360 ˚, Maximum 400 ˚/Second Speed Tilting Range & 0 ˚ to 180 ˚, Maximum 400 ˚/Second Speed Auto Panning Maximum 8 points Preset Group Touring Maximum 9 Groups Pattern 1 EA Auto Tracking Support Video/...
Security Password Protection, HTTPS (SSL, TLS) IPv4 and TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP IPv6 Protocol IPv4 FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG) Remote S/W LG Ipsolute VMS or Web Client Connections Up to 10 Misc. Protection...
LNP3700T/LNP2800/LNP28800I Series Item LNP3700T LNP2800 LNP2800I Image Sensor 4.5 mm (1/4 type) CCD Lens x37 Zoom, F1.5(Wide End), F4.1(Tele End) x28 Zoom, F1.5 (Wide End) , F3.0 (Tele End) (f = 3.5 mm to 129.5 mm) (f = 3.5 mm to 98 mm) Resolution Up to 704 x 480 (NTSC), 704 x 576 (PAL) Minimum Illumination...