Operating Instructions LVC-A910 LVC-A911 LVC-A912 LVC-A913 Before installing and using the camera, please read these instructions thoroughly and retain them for later reference.
Page 2
Warning To prevent fire or shock hazard,do not expose the unit to rain or moisture. CAUTION To avoid electrical shock,do not open the cabinet. Refer servicing to quali- RISK OF ELECTRIC SHOCK fied personnel only. DO NOT OPEN Regulatory Notices For U.S.A This equipment has been tested and found to comply with the limits for a CAUTION:TO REDUCE THE RISK OF Class A digital device, pursuant to Part 15 of the FCC Rules.These limits...
Contents Features...3 Cautions for Safe Operation ...4 Operating Controls and Their Functions...5 Power IN/CONTROL ...6-7 External Key(A/D IN)...8 MENU DESCRIPTIONS ...9 CAMERA ID ...10 FOCUS MODE SET ...11-12 AWB SET ...13-14 AE SET ...15-17 SPECIAL SET ...18-19 MOTION DET ...20 F.
Cautions for Safe Operation Power Supply • Close to generators of powerful electromagnetic This camera must always be operated a 12V DC radiation such as radio or TV transmitters. power supply. Care of the unit Handling of the unit • Remove dust or dirt on the surface of the lens Be careful not to spill water or other liquids on the with a blower.
Operating Controls and Their Functions 1. Tripod adaptor This adaptor can also be attached on the bottom of the camera. 2. Lens mount cap 3. TELE Key When push the TELE KEY, picture is telephoto 4. WIDE Key When push the WIDE KEY, picture is wide angle 5.
MENU DESCRIPTIONS Using TELE, WIDE, FOCUS+, FOCUS- button TELE and WIDE are used for UP and DOWN. • FOCUS+ and FOCUS- are used for INCREASE and DECREASE the data. • page 10 page 10 page 11-12 page 11-12 page 13-14 page 13-14 page 15-17 page 15-17...
CAMERA ID 1. CAMERA ID To connect a large number of camera , It can be assigned to identification number to each camera for camera control easily. (OFF, 0 - 255 : total numbers of ID are 256) • It only can be set this function using ID commend. To transfer ID Code of camera , In first byte at PC control.
FOCUS MODE SET 2. Focus Set: 2-1. Focus Mode Set : This function is for focus mode setting A) Set up "FOCUS SET" in main menu using Menu key. Select the "FOCUS MODE" in submenu using Tele/Wide key. And then set the mode (Auto, Push auto, or Manual) using Focus key.
FOCUS MODE SET 2-4. ZOOM END Set : This function is for selection of zoom end position. A) Select the "ZOOM END" in submenu using Tele/wide key. B) Set the Zoom end mode from X(Zoom Start + 1) to x176 using Focus key.
AWB SET 3. AWB SET 3-1. WB Mode Set : This function is for changing the WB mode. A) Set up "AWB SET" in main menu using Tele/wide key. B) Select the "WB MODE" in submenu using Tele/wide key. C) Set the mode Auto, Push auto , Manual, Outdoor, Indoor, Special using Focus key.
Page 14
AWB SET 3-3. BLUE ADJUST Set : This function is available for Special, Push Auto, Manual WB mode. This mode is the adjustment of user option for special color. A) Select the "BLUE ADJUST" in submenu using Tele/wide key. B) Adjust the level from (-30 to 30 SPECIAL, -128 to +127 PUSH AUTO, 0-255 MANUAL) using Focus key.
AE SET 4. AE SET 4-1. AE Mode Set : This function is for changing to AE mode. A) Set up "AE SET" in main menu using Tele/wide key. B) Select the "AE MODE" in submenu using Tele/wide key. C) Set the mode auto, IRIS MAN, AGC MAN, Manual, Auto using Focus key.
Page 16
AE SET 4-4. BRIGHTNESS ADJUSTMENT Set : A) Select the "BRIGHTNESS" in submenu using Tele/wide key. B) Adjust the level from ##MIN to ##MAX. using Focus key. * ## : Current level at Auto mode. 4-5. BACKLIGHT Set : A) Select the "BACKLIGHT" in submenu using Tele/wide key. B) Set the mode OFF, ON, or AUTO using Focus key.
Page 17
AE SET 4-7. SHUTTER SPEED Set : A) Select the "SHUTTER" in submenu using Tele/wide key. B) Set the mode NORMAL, 1/125 - 1/10000 using Focus key. 4-8. INITIAL SET : A) Select the "INITIAL SET" in submenu using Tele/wide Command, B) Set the initial set mode to ON or OFF using Focus key.
SPECIAL SET 5. SPECIAL SET 5-1. User Title Set : This function is for custom title on screen display. A) Set "SPECIAL SET" in main menu using Tele/wide key. B) Select the"USER TITLE" in submenu using Tele/wide key. C) Set the position of title and set data using Tele / Wide, Focus key.
SPECIAL SET 5-5. NEGATIVE Set : This mode is to change color and luminance to negative. A) Select the "COLOR" in submenu using Tele/wide key. B) Select the mode ON, OFF using Focus key. 5-6. WIDE BURST Set : This mode is to change color burst width for long dis- tance application.
MOTION DET 6. MOTION DETECTION SET 6-1. DETECTION Mode Set : A) Set "MOTION" in main menu using Tele/wide key. B) Select the "DETECTION" in submenu. Using Tele/wide key. C) Set the mode ON, OFF using Focus key. 6-2. LEVEL ADJUST Set : This function is available for DETECTION ON mode.
F. OSD SET 7. F. OSD SET 7-1. FUNCTION Set : A) Set "F. OSD" in main menu using Tele/wide key. B) Select the mode what you want in submenu using Tele/wide key. C) Set the display mode of OSD using Tele / Wide, Near/Far key. *INITIAL SET and RETURN are the same as before procedure.
E. SENSITIVITY SET 8. E. SENSITIVITY SET: (option) 8-1. E. SENSITIVITY SET A) Select the "E.SENSITIVITY" in submenu using Tele/wide key. B) Select the sensitivity mode what you want in submenu using Focus key. * Mode sequence : OFF-X2 AUTO-X4 AUTO-X8 AUTO- X10AUTO-X16 AUTO- X32 AUTO -OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF 8-2.
WDR SET 9. WDR SET (option) 9-1. WDR SET A) Select the "WDR" in main menu using Tele/wide key. B) Select the "WDR CONTROL" in submenu using Tele/wide key. C) Select the WDR mode what you want in submenu using Focus key. * Mode sequence : OFF -- ON -- AUTO * WDR Auto mode is working at the condition of high light back light.
On Screen Display FUNCTION Some of these functions will 1. Focus Mode be displayed every time the camera is operated and then disappeared after 5 seconds. 2. Back Light 3. Shutter Speed 4. CAMERA ID 5. ZOOM Display OSD Format Description Non display Auto Mode...
On Screen Display FUNCTION OSD Format Description 6. STAND-BY Indicate the camera stand-by during the camera’s power turning ON. 7. WBC Mode White Balance AUTO Special Auto White Balance; Adjustment Mode according to change of external illuminant. RED ADJUST and BLUE ADJUST (0~255) are available.
X 22 Zoom ( F 1.6 f = 3.9 ~ 85.8 mm ), Video AF Digital Zoom Ratio X 8 ( Total Zoom Ratio X 176 ) Minimum illumination LVC-A910/912 SERIES : 1 Lux, AGC On LVC-A911/913 SERIES : 0.01 Lux, X 32 Field Accumulate More than 48dB Scanning System...
Page 27
Specifications Focal Length 0.01m (WIDE), 1.0m (TELE) OSD(On Screen Display) ON/ OFF Power requirement DC 12V Video output Composite Output 75Ω Terminated / Y,C Separated Power consumption operating temperature 0°C - 45°C Operating Humidity 0% RH - 60% RH Storage temperature -20°C - 60°C, 0% RH - 85% RH Dimensions 56.2mm(W) x 64mm(H) x 101mm(D)
Page 37
当连接多台摄像机时 可以为每台摄像机指定一个识别 码 这样就可以更容易的对每台摄像机进行控制 (OFF, 0 - 255 ID 总数为 256) 只能使用推荐的 ID 来设置此功能 • 要发送摄像机的 ID 代码 使用 PC 控制的第一个字节 设置摄像机的 ID 编号 然后 ID 编号将连续显示...
Page 38
2-1. A) 使用菜单键在主菜单中设置 FOCUS SET 使用 Tele/Wide 键选择子菜单中的 FOCUS MODE 然后使用 对焦键设置模式 Auto(自动) Push auto(强制自动) Manual(手动)) 2-2. A) 使用 Tele/Wide 键选择子菜单中的 FOCUS DIST B) 使用对焦键在 1cm 到 5M 之间设置对焦距离模式 (1cm, 10cm, 50cm, 1M, 3M, 5M) 2-3. A) 使用 Tele/Wide 键选择子菜单中的 ZOOM START B) 使用对焦键在...
Page 39
2-4. A) 使用 Tele/Wide 键选择子菜单中的 ZOOM END B) 使用对焦键在 变焦开始 + 1 x176 到 X 之间设置变焦结束模式 2-5. A) 使用 Tele/Wide 键选择子菜单中的 ZOOM SPEED B) 使用对焦键设置变焦速度 Slow 低 Middle 中 Quick 快 2-6. A) 使用 Tele/Wide 命令选择子菜单中的 ZTRK B) 将变焦跟踪模式设置为 Auto 自动 或 Manual 手动 2-7.
Page 40
3-1. A) 使用 Tele/Wide 键在主菜单中设置 AWB SET B) 使用 Tele/Wide 键选择子菜单中的 WB MODE C) 使用对焦键设置模式 Auto(自动) Push auto(强制自动) Manual(手动) Outdoor(室外) Indoor(室内) Special(特殊) *WBC MODE: 1) AUTO 白平衡范围 2800 °K ~ 8000 °K 2) PUSH AUTO 将 AWB 模式设为 Push Auto 强制自动 则白...
Page 41
3-3. Special Push Auto Manual WB A) 使用 Tele/Wide 键选择子菜单中的 BLUE ADJUST B) 使用对焦键调节值大小 -30 到 30 SPECIAL -128 到 +127 PUSH AUTO 0-255 MANUAL 3-4. PUSH AUTO PUSH AUTO WB 3-5. A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 3-6.
Page 42
4-1. A) 使用 Tele/Wide 键在主菜单中设置 AE SET B) 使用 Tele/Wide 键选择子菜单中的 AE MODE C) 使用对焦键设置模式为 ATUO IRIS MAN AGC MAN Manual 4-2. IRIS MAN A) 使用 Tele/Wide 键选择子菜单中的 IRIS ADJUST B) 使用对焦键在 ##MIN 到 ##MAX(MANUAL, IRIS MAN) 中调整设 置 * ## : 自动模式当前值。 4-3.
Page 43
4-4. A) 使用 Tele/Wide 键选择子菜单中的 BRIGHTNESS B) 使用对焦键在 ##MIN 到 ##MAX 中调整设置 * ## : 自动模式当前值 4-5. A) 使用 Tele/Wide 键选择子菜单中的 BACKLIGHT B) 使用对焦键设置模式为 OFF ON 或 ATUO W当区域 1 区域 2 区域 3 或区域 4 中的背光满足条件时 可使用背光补偿 当此区域中的背光条件消失时 BLC 自动 停用...
Page 44
4-7. A) 使用 Tele/Wide 键选择子菜单中的 SHUTTER B) 使用对焦键设置模式为 NORMAL 1/125 - 1/10000 4-8. A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 4-9. A) 使用 Tele/Wide 键选择子菜单中的 RETURN B) 使用对焦键设置返回模式...
Page 45
5-1. A) 使用 Tele/Wide 键在主菜单中设置 SPECIAL SET B) 使用 Tele/Wide 键选择子菜单中的 USER TITLE C) 使用 Tele / Wide 和对焦键设置标题位置和数据 5-2. A) 使用 Tele/Wide 键选择子菜单中的 SHARPNESS B) 使用对焦键在 0 到 15 之间设置 5-3. A) 使用 Tele/Wide 键选择子菜单中的 MIRROR B) 使用对焦键设置模式为 ON OFF 5-4.
Page 46
5-5. A) 使用 Tele/Wide 键选择子菜单中的 COLOR B) 使用对焦键设置模式为 ON OFF 5-6. A) 使用 Tele/Wide 键选择子菜单中的 WIDEBURST B) 使用对焦键设置模式为 ON OFF 5-7. SPECIAL A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 5-8. A) 使用 Tele/Wide 键选择子菜单中的 RETURN B) 使用对焦键设置返回模式...
Page 47
6-1. A) 使用 Tele/Wide 键在主菜单中设置 MOTION B) 使用 Tele/Wide 键选择子菜单中的 DETECTION C) 使用对焦键设置模式为 ON OFF 6-2. DETECTION ON A) 使用 Tele/Wide 键选择子菜单中的 LEVEL SET B) 使用对焦键调整到某一敏感度 6-3. MOTION A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 6-4. A) 使用...
Page 48
F. OSD 7. F. OSD 7-1. A) 使用 Tele/Wide 键在主菜单中设置 F. OSD B) 使用 Tele/Wide 键在子菜单中选择您所需的模式 C) 使用 Tele / Wide 键和 Near/Far 键设置显示模式 *INITIAL SET RETURN...
Page 49
8. E. 8-1. E. A) 使用 Tele/Wide 键选择子菜单中的 E.SENSITIVITY B) 使用对焦键在子菜单中选择您所需的敏感度模式 : OFF-X2 AUTO-X4 AUTO-X8 AUTOX10AUTO-X16 AUTO- X32 AUTO -OFF- X2 FIX-X4 FIX -X8 FIX -X10 FIX -X16 FIX - X32 FIX-OFF 8-2. E.SENSITITY A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为...
Page 50
9-1. A) 使用 Tele/Wide 键在主菜单中设置 WDR B) 使用 Tele/Wide 键选择子菜单中的 WDR CONTROL C) 使用对焦键在子菜单中选择您所需的 WDR 模式 : OFF -- ON -- AUTO * WDR 9-2. A) 使用 Tele/Wide 键选择子菜单中的 SENSITIVITY B) 使用对焦键调整到某一敏感度 9-3. A) 使用 Tele/Wide 键选择子菜单中的 INITIAL SET B) 使用对焦键将初始模式设为 ON 或 OFF 9-4.
Page 53
320 线 PAL 普通分辨率 (屏幕中央) X 22 变焦 ( F 1.6 f = 3.9 ~ 85.8 mm ), 视频自动对焦 X 8 ( 总数码变焦 X 176 ) LVC-A910/912 SERIES : 1 Lux, AGC开 LVC-A911/913 SERIES : 0.01 Lux, X 32场累积 大于48dB 2:1隔行...
Need help?
Do you have a question about the LVC-A910 and is the answer not in the manual?
Questions and answers