Fender Stereo Amplifier Operating Instructions Manual page 7

A . IEC LINE CORD CONNECTOR
c o rd must be connected to a grounded AC
receptacle in accordance with the voltage
and frequency rati ngs as listed on the re a r
panel under I N P U T P O W E R.
B . F O O T S W I T C H J A C K - Plug-in connection
for the FOOTSWITCH (P/N 0055592000) for
remote switching between channels, a n d
ON/OFF switching of both DSP effects cir-
cuits. NOTE: For proper operation of the
FOOTSWITCH, the DRIVE SELECT* s w i t c h
and both DSP effects D E F E AT* s w i t c h e s
must all be OUT. (A speaker-grade cord is
p referable to a coax guitar cord for connect-
ing the F O O T S W I T C H. )
C . STEREO SEND - This jack pro vides a line-
lev el stereo output from the pre-amp and
both DSP effects circuits of the Ultimate
C h o rus DSP. This output can be used in
conjunction with the STEREO RETURN {D}
as a patch point for external stereo eff e c t s
devices. (See "EFFECTS LOOPS - CON-
NECTION DIAGRAMS," page 8). This send
can also be used to feed a stereo signal to
two channe ls of a re c o rd i n g / s o u n d - re i n-
f o rcement mixer. To drive another Ultimate
C h o rus DSP as an "add-on" amplifier, con-
nect a shie lded stere o cord from the
S T E R E O SEND jack of the "master" amplifi-
er to the S T E R E O RETURN j a c k { D } of the
"add-on" amplifier.
D . STEREO RETURN - This stereo jack inputs
signal directly to the left and right power-
amps. It automatically disconnects the pre -
amp and DSP Effects circuits when used.
This is useful when using the stereo eff e c t s
loop option detailed above, or when using a
second Ultimate Chorus DSP as an "add-on"
amplifier pre s e rving the s t e reo signal of the
"master" Ultimate Chorus DSP amplifier.
• N O T E : The S T E R E O jacks {C & D} a re stan-
d a rd 1/4-inch Ti p - R i n g - S l e e v e types, with:
•Left channel signal on the Ti p
•Right channel signal on the Ring
ULTIMATE CHORUS DSP - REAR PANEL
- The line
E . MONO SEND - This jack provides an imped-
ance-balanced mono output signal from the
p re-amp at a point before the DSP Effects cir-
cuits. This output can be used in conjunction
with the MONO RETURN j a c k {F} as a patch
point for external mono effects devices. (See
"EFFECTS LOOPS - CONNECTION DIA-
G R A M S ," page 8) The MONO SEND j a c k c a n
also be used to send re c o rd i n g / s o u n d - re i n-
f o rcement consoles a dry signal. Additionally
this output can be used to drive a second
Ultimate Chorus DSP as an "add-on" amplifier.
This is done by connecting a standard guitar
c o rd from the MONO SEND jack of the "mas-
ter" amplifier to the M O N O RETURN j a c k { F } o f
the "add-on" amplifier.
F. MONO RETURN - This balanced jack inputs
signal to the stereo DSP Effects circ u i t ry
which drives the stereo power-amp section.
It automatically disconnects the pre - a m p
signal when used. This is useful when using
the mono effects loop option detailed above
or when using the Ultimate Chorus DSP as
an "add-on" amplifier for a mono s i g n a l
s o u rce. The DSP Effects are active in the
"add-on" amplifier so that a true stere o
image will be generated if the DSP Eff e c t s
a re used. NOTE: In order to function pro p-
e r l y, a dummy plug or an extra guitar cord
must be inserted into INPUT 2* on the "add-
on" amplifier with its V O L U M E* c o n t ro l s
t u rned down.
*These controls are located on the Front Panels.
7