Advertisement
Available languages
Available languages
A. INPUT 1 - A high-impedance plug-in connection
for guitars or other instruments.
B. I N P U T 2
-
A
connection for guitars or other instruments with
active pre-amps.
identical impedance when used simultaneously.
• N o rmal Channel must be active for contro l s
{ C .-H . } to function, see DRIVE SELECT {P}.
N
N
C. NORMAL VOLUME
loudness of the amplifier.
O
O
D. TREBLE - Adjusts the high-frequency range.
R
R
E. NORMAL CHANNEL LED - Illuminates when
the Normal Channel is active.
M
M
F. MID - Adjusts the mid-frequency range.
G. BASS - Adjusts the low-frequency range.
A
A
H. RVB/DLY LEVEL - Adjusts the amount of
L
L
REVERB/DELAY type DSP Effects to be mixed-
in with the original dry signal.
•Drive Channel must be active for controls {I.–O.
and
Q . – R . }
to
SELECT {P}.
•
I. GAIN - Adjusts the amount of pre-amp gain
(distortion). Use with DRIVE VOLUME {L} to
control the overall amplifier loudness.
J. MID BOOST - Activates a special pre -
emphasis filter which accentuates mid-range
D
D
frequencies with this switch IN.
K. PRESENCE - Adjusts the the post-distortion
ultra-high frequency range.
R
R
L. DRIVE VOLUME - Adjusts the post-distortion
volume. Use with GAIN {I} to control overall
amplifier loudness.
I
I
M. DRIVE CHANNEL LED - Illuminates when the
Drive Channel is active.
V
V
N. TREBLE - Adjusts the high-frequency range.
O. MID - Adjusts the mid-frequency range.
P. DRIVE SELECT -
E
E
Normal Channel is active with switch OUT,
Drive Channel is active with switch IN.
• NOTE: The Channel-Select FOOTSWITCH is
disabled with this switch IN.
Q. BASS - Adjusts the low-frequency range.
•
R. RVB/DLY LEVEL - Adjusts the amount of
REVERB/DELAY type DSP Effects to be mixed-
in with the original dry signal.
ULTIMATE CHORUS DSP - FRONT PANEL
lower-impedance
plug-in
NOTE:
Both inputs have
- Adjusts the overall
function,
see
D R I V E
S . D E F E A T - Mutes the R E V E R B / D E L AY t y p e
DSP Effects with this switch IN.
must be OUT to enable remote switching
f rom the F O O T S W I T C H .
T. T Y P E
-
Selects
R E V E R B / D E L AY DSP Effects.
switch {S} must be OUT, the LEVEL controls {H &
R} must be above "1," and REVERB/DELAY on
the remote
FOOTSWITCH (if used) must be
active for this DSP effect to be heard. (See "DSP
STEREO EFFECTS - CONTROLS," page 6.)
U . D E F E A T - Mutes the C H O R U S / M O D U L AT I O N
type DSP Effects with this switch IN.
switch must be OUT to enable re m o t e
switching from the F O O T S W I T C H .
V. L E V E L
-
Adjusts
CHORUS/MODULATION type DSP Effects to be
mixed in with the original dry signal.
W. TYPE - This control selects one of sixteen various
C H O R U S / M O D U L ATION DSP Effects.
DEFEAT switch {U} must be OUT, the
c o n t ro l
{ V }
must
C H O R U S / M O D U L ATION
FOOTSWITCH (if used) must be active for this
DSP Effect to be heard.
EFFECTS - CONTROLS," page 6.)
X . R AT E - Adjusts the sweep R ATE of the
C H O R U S / M O D U L ATION type DSP Eff e c t s .
Lower numb ers correspond to slower sweep
R AT E S.
Y. DSP PEAK
L E D - Flashing of this LED
indicates possible clipping (distortion) in either
of the DSP effects circuits. Periodic flashing is
n o rmal. If the LED stays on and undesirable
d i s t o rtion is heard, try reducing L E V E L S
{ H , R , V } or the V O L U M E c o n t ro l s { C & L }.
Z. POWER SWITCH - Press IN the:
• Lower-half to switch ON the amplifier.
• Upper-half to switch OFF the amplifier.
5
Switch
one
of
sixteen
various
The D E F E AT
the
amount
LEVEL
be
above
"1,"
on
the
re m o t e
(See "DSP STEREO
This
of
The
and
Advertisement
