NAPCO Gemini GEM-X255 Installation Instructions Manual page 42

!
Page 42
750mS (.75 sec.): The slowest loop-response time, recommended for use with magnetic contacts, window foil, etc. Unless
programmed otherwise, loop-response time will be 750mS for all zones.
50mS (.05 sec.): Used for momentary Panic Buttons and area-protection devices, such as photoelectric eyes, passive infrared
sensors, floor mats, etc.
10mS (.01 sec.): An extremely fast loop response used primarily for window bugs.
Low Battery (Required for UL Mercantile installations)
A low-battery system trouble will annunciate at the keypad when the battery terminal voltage drops below normal. This condition
may signal a local sounding device, report to a central station (program Panel Low Bat Report Code), or both. If a battery is installed
and low terminal voltage is detected, a restore will not occur until the battery is recharged to its specified level and passes a dynamic
test. The dynamic test may be initiated manually by pressing the
by the panel.
In wireless installations, when displaying RF transmitter status, a "LoBatt" indication denotes a low-battery condition at the
transmitter.
Master Security Code
Dealer Security Code
Download Security Code
The factory-programmed Master Security Code (printed on the label affixed to the micro can) is unique and cannot be changed.
Use this code to enter the Dealer Program Mode to program (or change) the Dealer Security Code. If a Dealer Security Code is
programmed, both the Dealer Security Code and the Master Security Code will work. However, should system RAM fail, only the
Master Security Code will work.
The Dealer Security Code is needed to enter the Dealer Program Mode, thus allowing the dealer to program codes, zone
features, reporting features and zone descriptions (see Programming Manual WI777). This code may be changed as required.
Important! The label containing the Master Security Code should be removed. Record the code in a secure place for reference as
programming changes cannot be made without it (or the Dealer Security Code).
To change the Dealer Security Code, access the Direct Address Program Mode. Advance to the "PROG" screen, then change the
6-digit code as required.
The Download Security Code is the six-digit code required to establish connection to the PCD3000 Software.
Memory Failure
A User or Dealer Memory error will cause the sounder to pulse, the "SYS/TRBL" reminder to flash, and the display to read "E19-00
USER MEM ERROR " or "E20-00 DEALER MEM ERROR". Press the
"SYS/TRBL" reminder). Activate RESET SYSTEM TROUBLE to manually reset the system trouble. A Memory Failure can be
programmed to activate an alarm output and/or report using its associated system Report Code.
Modem IIe CS Format
The GEM-P9600 control supports Radionics Modem IIe central station reporting format.
Never Arm (Do not use for primary Burglary protection)
A zone programmed as Never Arm cannot go into alarm. If tripped, it will display at the keypad when the DISPLAY STATUS
function is selected. A chime will sound at the keypad while armed or disarmed, if Chime is also programmed for that zone and
enabled. This feature is suggested for use as a garage-door or driveway monitor, or similar application.
No EOL Resistor
Program for any zone not wired with a 2200 Ohm end-of-line resistor (Napco Part No. EOL2.2K). This will disable any zone-short
indication (if programmed, Day Zone Short is disabled). If not programmed, an end-of-line resistor must be installed. Note: This
selection is automatically disabled for zones selected as Fire.
Number of Rings Before Pickup See Callback-Method Download
One-Button Arming See Easy Arming
Opening Report
Opening Report Only After Alarm Report (Do not program for UL installations)
Opening and closing reports are generally used in commercial installations. On disarming, the communicator can send an
Opening Code for Users 1–96 (Opening Report), or it may transmit only when the control panel is disarmed after an alarm has been
reported (Opening Report Only After Alarm Report). (Note: Key Fobs 1–8 report as Users 81–96.) Subscriber Identification Numbers
and Opening Codes must be entered for either opening report.
Program Opening Report Only After Alarm Report to report only when disarming after an alarm report. This feature may be used
by the central station to verify that the subscriber has responded and disarmed the panel. If Opening Report Only After Alarm Report
is selected, also select Opening Report for each user.
Opening/Closing Reporting for Key-fob Users
Key-Fob users can now report openings and closings.
GEM-P9600: Key Fobs 1-16 report as Users 81-96.
Panic Zone
Keypad Aux Panic
X
GEM-X255 Installation Instructions
button, or it will be initiated automatically, every four hours,
C
button to silence the sounder ("SYSTEM READY" will display, along with the
C
WI1093A 12/01
L
NAPCO Security Systems