NAPCO Gemini GEM-X255 Installation Instructions Manual page 37

WI1093A 12/01
Dial-Tone Detection
Disable Auto Dial-Tone Detection
The panel features automatic dial-tone detection to ensure that a dial tone is present before the communicator dials. To disable
this feature, program an "8" in Location 4084.
When an "E" is programmed before the first digit of an outside telephone number, the communicator dial-tone detection circuit is
set to detect the standard 440Hz dial tone. The "E" is generally entered in the location immediately preceding the telephone number.
It may be necessary to program at least one 4-second pre-dial delay before a dial-tone detection "E". With certain nonstandard
exchanges, pre-dial delay "D"s may be used without a dial-tone detection "E". (See Access Number for Outside Line; Pre-Dial Delay;
Telephone Numbers.)
Digital Dialer Test
Activating the digital dialer test from the Function Menu (ACTIVATE DIALER TEST) will send the programmed report code to the
central station. Program DD TEST for SYSTEM-TROUBLE REPORTS and enter a DD TEST Report Code. Note that in this case the
report code received is not indicative of a system trouble, but is an indication of a successful transmission. Should the transmission
fail, the keypad will display "E03-00 COMM FAIL". This system trouble may be reset by pressing the
subsequent report will also clear the system trouble.
Disable Answering Machine Download See Callback-Method Download
Disable Auto-Reset on Day Zone See Day Zone
Disable Auto Status
Non 24-Hour Zones that are open (or shorted) normally display "ZONE FAULTS" (while disarmed) followed by the zone number(s) and
description(s). In high-security applications, program Disable Auto Status. Unsecured zones will then be indicated by a "CHECK STATUS"
display. Status may be displayed manually using the DISPLAY STATUS function, however a valid user code will be required.
Disable Auto-Unbypass on Disarming
Normally, manually bypassed zones revert to active (disarmed) zones on disarming. Select this feature to maintain bypassed
zones on disarming until manually unbypassed.
Disable Call Waiting (TouchTone® Dialing Only)
A digital communicator connected to a telephone line with Call Waiting may be disrupted by this feature. However, most lines with
Call Waiting also have Selective Call Waiting, which permits the feature to be turned off by dialing a "*70" just before the telephone
number. A "*" will be dialed by programming a "B".
If the installation has the Call Waiting feature, be sure that it also has Selective Call Waiting, and confirm the disable code with
the telephone company. Then program this code ("B70") directly before the phone numbers (after dial-tone detection or pre-dial delay)
in the telephone-number locations. See Telephone Numbers.
Caution: Should the user cancel his Call Waiting service, the communicator will dial a wrong number unless the phone number is
corrected.
Disable Callback Download See Callback-Method Download
Disable Code Required for Easy Bypass See Selective Bypass (Do not program in UL Installations)
Disable Code Required for Function Mode Level 1
Intended primarily for residential applications, this feature eliminates the user code requirement to access the Function Mode (for
Level-1 Users only), rendering the system more user friendly.
Disable Fire Reset (by Area)
Normally, pressing the C
any area, the C button will no longer activate the Reset Output so that the integrity of the smoke detector's Alarm Memory
feature (LED indication) will be maintained. Also see Alarm Outputs; Smoke Detectors.
Disable Function-Mode Download See Callback-Method Download
Disable Openings/Closings
Provides the flexibility of disabling openings and/or closings from any area(s).
Disable Wait-for-Handshake/Kissoff
Causes data transmission to start immediately after the telephone number.
Disable Wait-for-Silence (Pager Format)
Causes data transmission to start immediately after the pager telephone number.
Double Reporting See Report Telco 3
Download Security Code See Master Security Code
Download To an Armed Panel
This allows the panel to accept a download even if Armed. However if the programming to be altered effects the arming profile of
the control, such as zone features, it is recommended that the panel be disarmed and then rearmed to allow these changes to be
processed properly. Any program changes such as adding/changing user codes, adding users to an area, or changing Entry/Exit
Delays will be processed properly with the panel armed.
L
NAPCO Security Systems
button will momentarily remove power to the smoke detectors. If Disable Fire Reset is selected for
C button. Any successful
X
GEM-X255 Installation Instructions
!
Page 37