NAPCO Gemini GEM-X255 Programming Instructions Manual
  1. Manuals
  2. Brands
  3. NAPCO Manuals
  4. Control Panel
  5. Gemini GEM-X255
  6. Programming instructions manual

NAPCO Gemini GEM-X255 Programming Instructions Manual

Hide thumbs Also See for Gemini GEM-X255:
Table of Contents

Advertisement

Quick Links

See also: Operating Manual , Instruction and Installation Manual
HARDWIRE
CONTROL PANEL/COMMUNICATOR
Quick Start:
1. Refer to the wiring diagram, connect the keypad(s), siren, aux. power, aux. output, remote bus, earth ground, zone and telephone
wiring. NOTE: See Installation Instructions (WI1093).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 52).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press EEEEEE A
Press NO (g) Until "ACTIVATE PROGRAM Y/N" appears on the keypad display.
Press YES (F) To Enter Dealer Program Mode. (see page 6 for programming guide).
© Napco 2002
R
G E M - X 2 5 5
GEMINI
A
B
C
COMPUTERIZED SECURITY SYSTEM
Master Security Code
(on microshield)
PROGRAMMING
INSTRUCTIONS
SYSTEM ARMED
SYSTEM ARMED
01/01/00 12:00 AM
01/01/97
12:00AM
NEXT/YES
1 2
3
E
D
PRIOR/NO
4
5 6
F
AREA
7 8 9 0
G
GEM-RP1CAe2
WIRELESS
R
W1092B 9/02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Gemini GEM-X255 and is the answer not in the manual?

Questions and answers

Related Manuals for NAPCO Gemini GEM-X255

Summary of Contents for NAPCO Gemini GEM-X255

  • Page 1 4. Access the Easy Menu Driven (Dealer Program) Mode: Press EEEEEE A Master Security Code (on microshield) Press NO (g) Until “ACTIVATE PROGRAM Y/N” appears on the keypad display. Press YES (F) To Enter Dealer Program Mode. (see page 6 for programming guide). © Napco 2002 W1092B 9/02...

  • Page 2: Wi1092B

    GEM-X255 system comprising 96 zones or less, the system may be keypad programmed. A system larger than 96 zones must be downloaded with NAPCO PCD-Windows Version 4.1. This manual contains Easy Program Mode instructions, which allows the the first 96 zones to be completely programmed through Menu Driven Easy Program Mode.

  • Page 3: Table Of Contents

    TRAINING, EXPERIENCE AND INSTALLATION EQUIPMENT. IT IS RECOMMENDED THAT AFTER PROGRAMMING, THE ERROR CHECK UTILITY OF THE PCD3000 DOWNLOADER BE USED TO VERIFY THAT THE CONTROL PANEL PROGRAM CONTAINS NO ERRORS OR CONFLICTS WHICH MAY INHIBIT ITS INTENDED OPERATION. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 4: System Programming Options

    For a direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (J1) on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6-conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures.) Similarly, a high-speed local download may be made in the field using a notebook or laptop computer.

  • Page 5: Easy Menu Driven Program Mode

    Should it be necessary to create a new custom default program, (a) from the Dealer Program Mode, press the button to enter the Direct Address Program Mode; (b) access Location 4091 (Clear Program); (c) press the J button and start over. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 6: Gem-Rp1Cae2 Keypad

    Local System or C.S. Reporting System (Appears for New Panel Only) REPORT ALL ZONES Press YES ( ) button for all zones to report; press NO ( ) button TO CENTRAL? Y/N for no zones to report (LOCAL SYSTEM). (Press YES or NO) NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 7 F 0 7 1 5 1 6 8 4 2 9 4 0 0 • Go to Central Phone # input screen and press: [*] [5] [0] [7] [1] [5] [1] [6] [8] [4] [2] [9] [4] [0] [0] [ON/OFF] NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 8: Central Station Receiver 1 Account Number

    Sescoa, Vertex, DCI, Franklin Fast Radionics Modem 2 in Direct Address Programming. See CS Radionics Fast Receiver Options. Silent Knight Fast Ademco Point ID Radionics, DCI, Franklin Slow Ademco Express Universal High Speed Pager Radionics BFSK NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 9: Enter User Codes

    ARM ONLY LEVEL 3 ARM ONLY NONE SERVICE LEVEL 1 SERVICE LEVEL 2 SERVICE LEVEL 3 SERVICE Note: “Y” indicates option is enabled. Note: “Y” indicates option is enabled. Note: “Y” indicates option is enabled. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 10 CHANGING OR CANCELING A CODE: To change any code, merely program over the existing code as described above and press to save. Similarly, to cancel a code, blank out each number of the code and press to save to save. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 11: Rf Transmitter Points

    Press NEXT ( ) button to proceed. Quick Method. If a receiver is already installed in the panel, Napco Z N # X M I T # + C S P transmitter wireless points can be programmed automatically (“enrolled”) using the following procedure.

  • Page 12: Key Fob Transmitters

    Zone Number (e.g. “01”) and change the Zone Number using the buttons. Program a new description as above. NOTE: Zone Descriptions can only be entered through the GEM-/RP1CAe2 Keypad or by using the Napco Quickloader Software. Press NEXT ( ) button to proceed.

  • Page 13: Enter Time

    GEM-RP1CAe2 Keypad and Foreign Language configuration(similar to a new panel). Access address 4093, then press the button. Data entry is not allowed. NOTE: Some features (schedules) can only be programmed again with the Downloading Software. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 14: Direct Address Program Mode

    3. Press F To Enter Dealer Program Mode DIRECT ADDRESS PROGRAM MODE DISPLAY & COMMANDS = ADDRESS 0 0 0 0 3 C ( S E C O N D S ) 0000 3C = DATA ENTRY LOCATION (Left and Right NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 15: Programming Overview

    • make minor field alterations to an existing panel program. It is recommended that the panel be uploaded to NAPCO's Quickloader software following any keypad " programming and that the PCD-Window's error-check feature be utilized to reduce the possibility of "...

  • Page 16: Direct Address Programming Example

    5. Press to enter an “E” in the left digit and press to enter a blank (•) in the right digit. 6. Press to save. Address 1218 is now programmed with “E•”. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 17: Programming Options & Worksheets

    Determining data entry for a location (each “nibble”). Numbers in parentheses indicate data selected zones features. (See Programming Worksheets that follow.) DEFAULTS: The defaults shown on the following pages are automatically set after exiting the Easy Menu Driven NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 18 # OF ZONES IN AREA 1 AI #ZN =08 #KP=1 A2 #ZN=00 #KP=0 01/01/97 12:00AM ENTER # ZONES X X NEXT/YES PRIOR/NO AREA 7 8 9 0 COMPUTERIZED SECURITY SYSTEM THIS PAGE INTENTIONALLY LEFT BLANK NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 19 A. Choose a desired delay/timeout , ex: 20. Note: For Sensor Watch only divide it by 10, ex: 20/10 = 2 1 Quotient Left Digit B. Divide it by 16 16 20 4 Remainder Right Digit NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 20: Keypad System Codes (Addr 0490, 0495 & 0500)

    DEALER SECURITY CODE: Enter up to 6 digits to be used by the dealer to enter programming. 1. Enter in both left and right digits of address locations. 2. Valid entries are: 0-9. Note: If left blank, the Master Security Code must then be used to enter programming. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 21: Cs Receiver Opt

    (left and right). 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 22: Download/Callback Options (Addr 4089, 0600-0619, 0625-0647, 1022 & 1023)

    1. Enter in right digit only (left digit is not used). 2. Valid entries are: 0-9. 2. Valid entries are: 1 or 2. Note: Download Security Code must match the code entered in the PCD3000 Software. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 23 (RIGHT DIGITS 1-4) (RIGHT DIGITS 1-4) (RIGHT DIGITS 1-4) (RIGHT DIGITS 1-4) (RIGHT DIGITS 1-4) 0768 0769 0770 0771 0772 0773 0774 0775 0776 0777 0778 0779 0780 0781 0782 0783 0784 0785 0786 0787 NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 24: Cs Reporting Codes (Addr 0860-0869)

    Opening after Alarm blank (•) 0862 blank (•) 0867 NOTE: Dark shaded data value box Fail to Close 0868 shows option not available. [Default = blank (•) blank (•) from address 0859-0869] Fail to Open 0869 NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 25: Cs Reporting Codes (Addr 0870-0904)

    Leave blank (•) to select Rotary Dialing. 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 26: Cs Zone Reporting Codes (Addr 0910-0904)

    MODEM CODES determine the zone types reported for the following formats: SIA and ADEMCO Point Hold up Gas Alarm 1. Select the desired Modem Code for each zone from the table shown. Heat Alarm Auxiliary Alarm 24 Hour Auxiliary NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 27: Cs User Reporting Codes (Addr 1030-1081)

    User User LEFT RIGHT Telco 1 1-16 (see Easy Menu Program Driven User 199 = Easy Arming (Opening not applicable) Mode) will report as Users 180-195, blank (•) User 200 = Keyswitch Arming respectively. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 28 User User LEFT RIGHT Telco 3 1-16 (see Easy Menu Program Driven User 199 = Easy Arming (Opening not applicable) Mode) will report as Users 180-195, blank (•) User 200 = Keyswitch Arming respectively. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 29 (left and right). 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 30 1. Select the desired option by circling " the data values for each digit 2. Add the data values (ex: 15=1+2+4+8) from the selected options. (left and right). 3. Enter in address location (left and right digits). NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 31 1. Select the desired option by circling " the data values for each digit 2. Add the data values (ex: 15=1+2+4+8) from the selected options. (left and right). 3. Enter in address location (left and right digits). NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 32 Zone ANDing Group 8 1361 1261 Interior #1 Bypass 1362 1262 Interior #2 Bypass 1363 1263 Keypad Sounder on Alarm 1364 1264 Fire (C) 1375 1275 Fire Alarm Verification (C) 1376 1276 Chime 2 1386 1286 NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 33 Interior #1 Bypass 1562 1462 Interior #2 Bypass 1563 1463 Keypad Sounder on Alarm 1564 1464 Fire (C) 1575 1475 Fire Alarm Verification (C) 1576 1476 Chime 2 1586 1486 See Zone Options on Page 54. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 34 Interior #1 Bypass 1762 1662 Interior #2 Bypass 1763 1663 Keypad Sounder on Alarm 1764 1664 Fire (C) 1775 1675 Fire Alarm Verification (C) 1776 1676 Chime 2 1786 1686 See Zone Options on Page 554. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 35 Interior #1 Bypass 1962 1862 Interior #2 Bypass 1963 1863 Keypad Sounder on Alarm 1964 1864 Fire (C) 1975 1875 Fire Alarm Verification (C) 1976 1876 Chime 2 1986 1886 See Zone Options on Page 54. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 36 Interior #1 Bypass 2162 2062 Interior #2 Bypass 2163 2063 Keypad Sounder on Alarm 2164 2064 Fire (C) 2175 2075 Fire Alarm Verification (C) 2176 2076 Chime 2 2186 2086 See Zone Options on Page 54. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 37 Interior #1 Bypass 2362 2262 Interior #2 Bypass 2363 2263 Keypad Sounder on Alarm 2364 2264 Fire (C) 2375 2275 Fire Alarm Verification (C) 2376 2276 Chime 2 2386 2286 See Zone Options on Page 54. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 38 Fire, Pulse Alarm Output and Fire Verification is enabled for the zone numbers entered in “FIRE ZONES” Menu Driven program Mode. 2-Wire Smoke Detector is enabled for zone numbers entered in “2 WIRE FIRE ZONES” NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 39 (left and right). 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 40 NOTE: Dark shaded data value box shows option not available. ADDRESS ALARM/TROUBLE 3879-3881 REPORTING CODES LEFT ADDR RIGHT Wireless Low Battery blank (•) 3879 Wireless Supervisory blank (•) 3880 Wireless Tamper blank (•) 3881 [Default = blank (•) blank (•) from address 3879-3881] NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 41 (left and right). 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 42 Page 42 WI1092B 9/02 THIS PAGE INTENTIONALLY LEFT BLANK NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 43: Keypad Options (Addr 2425-2454)

    (left and right). 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 44: User Area Options (Addr 2500-2595)

    4 2 1 blank (•) 2500 NOTE: No circle = feature disabled. 4 2 1 4 2 1 ZN04 ZN03 ZN02 ZN01 4 2 1 4 2 1 Draw Circle 4 2 1 NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 45: Ezm Group Options (Addr 2600-2643)

    2. Enable desired options for each area by drawing a circle " around its corresponding binary data value. NOTE: No circle = feature disabled. 3. Enter data in corresponding left and right digit address locations above. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 46: Area Arming Options (Addr 2650-2657)

    (left and right). 2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in address location (left and right digits). NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 47: Area Output Control Options (Addr 2700-2739)

    2. Add the data values (ex: 15=1+2+4+8) from the selected options. 3. Enter in right digit address location. NOTE: Dark shaded data value box shows option not available. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 48 Type E Smoke Detector 3766 3774 Type 7 Smoke Detector Type F Napco Glass Break 3767 3775 [Default = blank (•) blank (•) from address 3760-3767] [Default = blank (•) blank (•) from address 3768-3775] RF SUPERVISORY TIMERS RF SUPERVISORY TIMERS...
  • Page 49 4093XX Access address 4093, then press the button. Data entry is not allowed. GEM-RP2ASe2 Keypad NOTE: Some features (schedules, language configuration) can only be re-programmed with the Downloading Software. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 50: User Program Mode

    Repeat this procedure for each user. To proceed to Zone-Description programming, press the NEXT ( ) button. NOTE: All 195 User Codes may be keypad programmed in both User and Dealer program modes. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 51: Zone Descriptions

    Advance to the next zone as in Steps 1 and 2 above and repeat this procedure until all zones have been programmed. NOTE: All 255 Zone Descriptions may be keypad programmed in both User and Dealer program modes. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 52: Keypad Configuration Mode

    A valid number will be acknowledged by a short beep; an invalid number will be rejected by a long beep. 2. Press the button to continue or press the button to exit. NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 53 Press the button to continue or press the button to exit the Keypad Configuration Mode (display will read 01 OUT OF SYSTEM “ ”). Then replace Jumper JP5 across Pins 1–2 (top two). NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 54: Keypad Programming Modes

    Minimum level required to access function TO ARM IN 1-4HRS Level 3 code with appropriate option Requires dealer code DISPLAY AUTO ARM SCHD ACTIVATE PROGRAM Initial Configuration only; suppressed thereafter ACTIVATE DOWNLOAD DISPLAY RF XMITTER STAT RELAY CONTROL NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 55 ACTIVATE DOWNLOAD DISPLAY RF XMITTER STAT Minimum level required to access function RELAY CONTROL Level 3 code with appropriate option Requires dealer code Not available in GEM-RP2ASe2 / GEM-RP3DGTL keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 56 ENTER DATE (MM/DD/YY) ENTER TIME (HH:MMA/P) ENTER DEALER CODE Minimum level required to access function Level 3 code with appropriate option Requires dealer code Not available in GEM-RP2ASe2 / GEM-RP3DGTL keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 57: User Mode

    RELAY CONTROL Press button (at any time) Minimum level required to access function Level 3 code with appropriate option Requires dealer code Not available in GEM-RP2ASe2 / GEM-RP3DGTL keypads Initial Configuration only; suppressed thereafter NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 58 Return Jumper JP5 * from Pins 2-3 to Pins 1-2 (“SYSTEM READY”) * JP5 is located at the top-right corner of the circuit board. ** If a Compatibility Number other than “0000” is programmed, “OLD COMPAT# XXXX” is displayed. NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 59: Programming Options Index

    CS Receiver 1 Options Direct Address 0526 CS Receiver 1 Telephone Number Direct Address 0527-0546 CS Receiver 2 Format Direct Address 0550 CS Receiver 2 Options Direct Address 0551 CS Receiver 2 Telephone Number Direct Address 0552-0571 NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 60 Entry Delay 2 Direct Address 0002 Entry/Exit 1 (Zone Option) Direct Address 1216, 1316, 1416 & 1516 32 - 37 Entry/Exit 2 (Zone Option) Direct Address 1217, 1317, 1417 & 1517 32 - 37 NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 61 RF Transmitter Points Easy Menu Driven RF Trouble Report Code Direct Address 0897 Selective Bypass (Zone Option) Direct Address 1205, 1305, 1405, . . ., 2305 32 - 37 Sensor Watch Report Code Direct Address 0877 NAPCO Security Systems GEM-X255 Programming Instructions...
  • Page 62 1245, 1345, 1445, . . ., 2345 32 - 37 Zone Options - Zones 1 To 96 Direct Address 1200-2376 32 - 37 Zones Report Code - Zones 1 to 96 Direct Address 0910-1005 NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 63: Gem-X255 Wiring Diagram

    WI1092B 9/02 Page 63 GEM-X255 WIRING DIAGRAM GEM-X255 WIRING DIAGRAM NAPCO Security Systems GEM-X255 Programming Instructions...

  • Page 64: Limited Warranty

    Page 64 WI1092B 9/02 NAPCO LIMITED WARRANTY In no event shall NAPCO be liable for an amount in excess NAPCO SECURITY SYSTEMS, INC. (NAPCO) warrants its products to be free from manufacturing defects in of NAPCO's original selling price of the product, for any...

Table of Contents