The Installation Space; Dimensions And Clearances - GE Monogram ZICP720 Installation Instructions Manual

Design Guide
THE INSTALLATION SPACE
The installation space must be 71-1/2",
f 71-1/2" F inished Width ........................................ f
ll
2-5'16" ',
"1 Wall
/k 5/'j E!ectrical f 24-3/ 6" -I View
--/ _ 6 , mm_ 6" |
!, 1 t
max I 10 i ]u .
83-I/2"tl ' 75 From
rain J_ 24"Cutout i Finished
Finished I Depth , Floorto
• I ,, Bottomof
upenmg | _" W " 5" Electrical
I /
"
t aterSupply ,, WaterSupply T Area
" i I _ j
/ I, i
Z ............ 26 ................... \ /: ............ 26" ................. \
3-1/2" 3-1/2"
Water And Electrical Locations
Electrical and water supply must be located
as shown.
The cutout depth must be 24"
The refrigerator will project forward, slightly
beyond adjacent cabinetry, depending on your
installation.
Cutout depth beneath a soffit:
When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top
case trim overlaps the bottom of the soffit.
Additional Specifications
cA separate 115 volt 60Hz., 15 or 20 amp power
supply is recommended for each product, An
individual properly grounded branch circuit or
circuit breaker is recommended. Install properly
grounded 3-prong electrical receptacles recessed
into the back wall, Electrical must be located on
rear wall as shown,
NOTE: GFI (ground fault interrupter)is not
recommended.
Both water lines can enter the opening through
the floor or back wall. Route GE SmartConnect"
kit or 1/4" O.D. copper tubing between the cold
water line and the water connection location.
The tubing should be long enough to extend to
the front of the refrigerator. Installation of an
easily accessible shut-off valve in the water
line is required.
DIMENSIONS AND CLEARANCES
71-1/2" 25-3/4"
Case Width Case Depth
83-1/2"
at Rear
28-11/16"
Depth Including
Handles
72"Frame
to Frame '
Width
Shipping height. T he
refrigerators c anbe
adjusted to fit intoa
cutoutthatis 83-1/2"
min. t o 84-1/2" m ax.
Notethatthetopcase
trim atthefrontis 1/2"
higher andwill overlap
uppercabinetry or
soffit.Useleveling legs
andwheelsfor a
maximum 1"height
adjustment.
Product Clearances
These refrigerators are equipped with a 2-position
door stop. The factory set 130 ° door swing can be
adjusted to 90 ° if clearance to adjacent cabinets
or walls is restricted.
25"_
Min.toi 130 ° Door
Wall
I
/L
0 ,!
H 130 ° Door
Swing Swing
11
q-' '-F
i L
__25"__I
Min.to
Wall
/,,
,, "":::",,:::,,::::!
Allow 25" minimum clearance for a full 130° door
swing. Allow 15" for pan removal.
5" minimum clearance is required when door swing
is adjusted to 90°, If the 90° door stop position is
used, pan access is maintained, but pan removal
is restricted.
See illustrations on pages
4 and 5 to determine door
swing interaction with
adjacent cabinets or
countertops,
T
90 ° Door 1 23-7/8"
Swing / Behind
, !, _Frame
L! i
!i 36-3/4-
90o .........
5" Minimum to
Wall