GE ZIC360N RH Design & Installation Manual
Built-in bottom-freezer refrigerators
Hide thumbs
Also See for ZIC360N RH:
- Design manual (20 pages) ,
- Installation instructions manual (20 pages) ,
- Service bulletin (4 pages)
Related Manuals for GE ZIC360N RH
Summary of Contents for GE ZIC360N RH
-
Page 1: Step 4, Install Anti-Lip Brackets
Installation Instructions ZIC360N RH,ZIC360NLH, ZICS360N RH,ZICS360NLH Built-In Bottom-Freezer Refrigerators Design Guide With Installation Instructions Monogram;' We bring good things to life... -
Page 2: Table Of Contents
IMPORTANT staller. Product failure due to improper installation • Save these instructions not covered under the GE Appliance Warranty. local inspector's use. Observe all governing the Owner's Manual for warranty information. codes and ordinances. • Note to Installer-... -
Page 3: Planning Guide Theinstallationspace
Design Guide THE INSTALLATION SPACE 38" DIMENSIONS CaseWidth CLEARANCES 35-1/2" _FinishedWidth_ finished Wall View cutout width * Shippingheight, The *84" From refrigeratorcanbe adjusted must be Floorto to fit into a cutoutthat is 35d/2". Top Frame 83-1/2"min, to 84-1/2"max, 10" _'_ Electrical Area trim at the front is 1/2"... -
Page 4: 130 ° Doorswing
Design Guide FramelessCabinets:The case trim overlaps cabinets at the to ) and sides. Therefore, frameless cabinets may require filler strips to prevent inter- Refrigerator ference with cabinet door swing. The 23-7/8"From opening must allow for filler strips. Rearof Refrigerator Case 3/4"... -
Page 5: 90 ° Door Swing
Design Guide FramelessCabinets:The case trim overlaps cabinets at the top and sides. Therefore, frameless Refrigerator cabinets may require filler _Case strips to prevent inter- ference with cabinet door swing. The opening must allow for filler strips. 23-7/8" FromRearof Refri_ erator .. -
Page 6: Customization Basics
This design provides ZICS360N LH seamless appearance which integrates smoothly with (left-handed door) Trimmed models: surrounding cabinetry. ZIC360N RH (right-handed door) ZIC360N LH (left-handed door) Stainless Steel Wrapped Refrigerators Stainless Steel wrapped refrigerators have wrapped doors and grille panel, beveled edges,... -
Page 7: Paneldimensions
Design Guide 1/4" FRAMED PANEL DIMENSIONS 1 5/16,' If you choose to install framed panels, they must be Trim I Door/Drawer Reveal cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. If the custom panel... -
Page 8: Side Panels
Design Guide SIDE PANELS ZUG2 GRILLE PANEL DIMENSIONS Side panels must be used whenever the sides of the The ZUG2 unified grille panel kit provides for the refrigerator will be exposed. The 1/4" side panels will installation of a framed or overlay grille panel. -
Page 9: Installation Instructions
Installation Instructions TOOLS REQUIRED MATERIALS REQUIRED • Tinsnips to cut banding • 35" long 2x4 for Anti-Tip support • Stepladder • Copper water line tubing • Bucket • Water shut-off valve (optional but recommended) • Level • Custom panels for fresh food door, freezer drawer •... -
Page 10: Step 1, Remove Packaging
Installation Instructions [STEP 11 REMOVE PACKAGING bolts securing the straps to the skid. CAUTION: Refi'igerator ismuch heavier atthe CAUTION: DO top thanatthebottom - be careful w hen moving. NOT ATTEMPT TO When using a hand truck, handle from side only. •... -
Page 11: Step 2A, Rowater Line
Installation Instructions [STEP 41 INSTALL ANTI-TIP [STEP 2A] WATER LINE BRACKETS INSTALLATION WITH A REVERSE OSMOSIS SYSTEM WARNING: ANTI-TIP PRECAUTIONS The refrigerator is top-heavy must be secured Skip this step when not using an RO System prevent the possibility of tipping forward. -
Page 12: Step 5, Level Refrigerator
Installation Instructions ISTEP 6] SECURE REFRIGERATOR ISTEP 5] LEVEL REFRIGERATOR TO CABINETRY All models have 4-point leveling. The front is sup- ported by leveling legs, the rear is supported Whenever possible, perform this step for anti-tip adjustable wheels. Both are accessible from the front security, or when anti-tip... -
Page 13: Step 7, Adjust Door Swing
Installation Instructions [STEP 71 ADJUST DOOR SWING [STEP 8 1 INSTALL GRILLE PANEL NOTE: This refrigerator has a 2-position door stop. , Raise the grill panel to stop position. When space does not allow the door to swing open 130°, fully to you may change the door swing to a 90 °... - Page 14 Installation Instructions [STEP INSTALL FRAMED PANELS Right hand models shown. Use the same instructions for left hand models. IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 9A. Handle DoorTrim Trim Refrigerator Door - UseFrontHoles to SecureTrim Standardsuppliedhandleshown in 1/4" panelposition, "_-_ Jse RearHoles to SecureHandle...
-
Page 15: Step 9A, Install Overlay Panels
Installation Instructions ISTEP 9A] INSTALL OVERLAY PANELS Right hand modelsshown. Use the same instructions for heft hand models. DoorTrim Handle Trim Refrigerator Door Move Forward For3/4" Panel UseFrontHoles to SecureHandle \Use RearHoles to SecureTrim Suppliedhandleshown inthe overlaypanelposition, Install door and drawer panels: •... -
Page 16: Step 11, Connect Power
Installation Instructions [STEP 12] START ICEMAKER I STEP 101CONNECT WATER SUPPLY Check to be sure that refrigerator power cord is not plugged into the wall outlet. • Flip the switch to I (ON). The icemaker will begin operation automatically. • Be sure nothing interferes with the sweep of the House... - Page 17 Notes...
- Page 18 Notes...
- Page 19 Notes...
- Page 20 Note: While performing installations described in this book, safety glasses or goggles should be worn, For Monogram _ local service in your area, call 1-800-444-1845, Note: Product improvement is a continuing endeavor General Electric. Therefore, materials, appearance specifications subject to change without notice.