Table of Contents
Related Manuals for GE ZICS360 LH
Summary of Contents for GE ZICS360 LH
-
Page 1: Installation Instructions
Installation Instructions If you have questions, call 800.626.2000 or visit our website at: www.monogram.com ZIC360N RH, ZIC360N LH, ZICS360N RH, ZICS360N LH Built-In Bottom-Freezer Refrigerators Design Guide With Installation Instructions Monogram. ®... -
Page 2: Table Of Contents
If you received a damaged refrigerator, you should immediately contact your dealer or builder. CAUTION: Due to the weight and size of this refrigerator, and to reduce the risk of personal injury or damage to the product—THREE PEOPLE ARE REQUIRED FOR PROPER INSTALLATION. -
Page 3: The Installation Space
Water And Electrical Locations Electrical and water supply must be located as shown. The cutout depth must be 24" The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation. Cutout depth beneath a soffit: When installed beneath a soffit, the soffit cannot exceed the 24"... -
Page 4: 130° Door Swing
Refrigerator Top View 130° DOOR SWING (factory setting) Scale 1:1 Design Guide Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler strips to prevent interference with 23-7/8" From cabinet door swing. The opening must Rear of allow for filler strips. -
Page 5: 90° Door Swing
Top View 90° DOOR SWING (optional setting) Scale 1:1 Design Guide Refrigerator Door Frameless Cabinets: The case trim overlaps cabinets at the top and sides. Therefore, frameless cabinets may require filler Case Trim strips to prevent interference with cabinet door swing. The opening must allow for filler strips. -
Page 6: Customization Basics
ZKHCSS2 Monogram stainless steel tubular handle kit for 3/4" overlay panels. Side Panels Side panels must be used whenever the sides of the refrigerator will be exposed. Framed Panel Accessory Panels White, black and stainless steel accessory panels are available from your Monogram dealer. -
Page 7: Panel Dimensions
1/4" FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille. If the custom panel is less than 1/4" thick and if it fits loosely in the door frame, it can be backed up with a piece of filler material or foam tape to improve the fit. -
Page 8: Side Panels
SIDE PANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4" side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer. -
Page 9: Tools, Hardware, Materials
™ • Water shut-off valve • Custom panels for fresh food door, freezer drawer and grille panel • Screws to secure refrigerator to cabinetry. • Stick-on hook and loop fastener strips for 1/4" side panels FLOORING For proper installation, this refrigerator must be placed on a level surface of hard material that is at the same height as the rest of the flooring. -
Page 10: Step 1, Remove Packaging
Carefully, tilt refrigerator and slide blocks out from beneath. • Remove toekick. Set aside for final installation. • Lift the refrigerator off the skid with an appliance dolly. Handle from the sides. ™... -
Page 11: Step 2A, Ro Water Line
• Gently push refrigerator into the opening with hands against front corners. Important Note: When the refrigerator is installed under a soffit or if there is not enough height for this method of security, brackets cannot be used. Proceed to step 5 to level the refrigerator and then to step 6 to secure refrigerator to cabinets. -
Page 12: Step 5, Level Refrigerator
Both are accessible from the front of the refrigerator. • To level the back of the refrigerator, turn the 7/16" hex nut located above the front wheels. Turn clockwise to raise or counterclockwise to lower the refrigerator. -
Page 13: Step 7 Adjust Door Swing
Installation Instructions STEP 7 ADJUST DOOR SWING NOTE: This refrigerator has a 2-position door stop. When space does not allow the door to swing open fully to 130°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory for your installation situation. -
Page 14: Step 9 Install Framed Panels
IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 9A. Handle Door Trim Trim Refrigerator Door Standard supplied handle shown in 1/4" panel position. • There are two sets of holes in the handle side trim. Replace handle side trim by installing the original screws in the FRONT screw holes. -
Page 15: Step 9A Install Overlay Panels
• Secure the door/drawer trim using both the FRONT and REAR screw holes. Discard supplied handle. Right hand models shown. Use the same instructions for left hand models. Door Trim Handle Trim Refrigerator Door Move Forward For 3/4" Panel Supplied handle shown in the overlay panel position. -
Page 16: Step 10 Connect Water Supply
Electrical Master Light Outlet Switch • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37°F for the fresh food section and 0°F for the freezer. -
Page 17: Step 13, Install Toekick
Installation Instructions STEP 13 INSTALL TOEKICK • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install with 2 screws provided, adjust to desired height and tighten screws. • A custom toekick can be installed to match or complement the surrounding cabinetry. - Page 18 Notes...
- Page 19 Notes...
- Page 20 Pub. No. 49-60136-2 Dwg. No. 164D4371P001 11-03 JR 15421-1 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. ® For Monogram local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric.