Design Guide (For Zifs240 And Zibs240); The Installation Space; Product Clearances; Side-By-Side Installations - GE ZIFI240 Installation Instructions Manual

For models ZIFS240 and ZIBS240 with Stainless Steel Doors and Handles

THE INSTALLATION SPACE

Locate
Outlet
8-1/2"
10-1/2"
9"
9" Max.
34-1/2"-35"
Max.
1-1/2"
1-1/2"
23-3/4" Min.
NOTE:
Handle and
handle standoff
26"
depth is 2-1/4".
Including
Handle
The cutout depth should be 24"
The cutout dimensions shown allow for a full door
swing and access to the pull-out racks when installed
in standard 24" deep cabinets.
• All models may be used freestanding.
• If installing a stainless steel model between frameless
cabinets, a 1/2" wide filler strip or side panel may be
needed on the hinge side. The filler strip will act as
a spacer between the case and adjacent cabinet door
swing. The width of the opening must include the filler
panels.
Note: The stainless steel door should be flush with the
surrounding cabinets.
Additional Specifications
• A 120 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch circuit
or circuit breaker is recommended. Install a properly
grounded 3-prong electrical receptacle recessed into
the back wall as shown. Electrical must be located on
rear wall as shown. NOTE: GFCI (ground fault circuit
interrupter) is not recommended.

SIDE-BY-SIDE INSTALLATIONS

For a complete refreshment center, install a Fresh-Food Refrigerator
beside a Double Drawer Refrigerator, Beverage Center or Wine Chiller/
Wine Reserve. Or, install a Refrigerator with Icemaker beside
a Wine Chiller/Wine Reserve.
• A side-by-side installation requires at least a 47-1/2" wide opening.
No trim kits required.
• Products must operate from separate, properly grounded receptacles.
Design Guide
NOTE:
24"
Water line location
for ZIBI240 or
ZIBS240 model only
23-3/4"
34-1/4"
to 34-3/4"
23-3/4"

PRODUCT CLEARANCES

The Fresh-Food Refrigerator or Bar Refrigerator with
Icemaker is factory set for a 110° door swing.
When installed in a corner:
• Allow 14" minimum clearance on the hinge side
for a full 110° door swing.
• Allow 4" min. clearance on the hinge side for
the 90° door swing and to allow racks to slide out.
NOTE: Clearances are based on the recommended
2-1/4" handle standoff depth.
14" Minimum to Wall
110° Door
Swing
110°
NOTE: Right hand models illustrated. Allow the same
clearances on the opposite side for left hand fresh food
models ZIFI240 and ZIFS240 only. Models ZIBI240 and
ZIBS240 are not available with left hand door swing.
• Test the door swing. Carefully open and close the door.
The door should not rub or catch on adjacent cabinetry.
Choose the location:
• These products may be closed in on the top and
three sides as long as the front is unobstructed for
air circulation and proper access to the door.
• Do not install these products where the temperature
will go below 55°F (13°C) or above 90°F (32°C).
• These products are not designed to be stacked one
over the other.
34-1/2"-35"
4
90° Door
21-5/8"
Swing
23-5/8"
90°
4" Minimum to Wall
Locate
Outlet
10-1/2" 10-1/2"
24"
14"
9" 9"
15"
1-1/2"
47-1/2" Min.