Ptzf - Movement Commands - Cisco PrecisionHD 1080p12x User Manual

Cisco TelePresence PrecisionHD Camera
Contents Introduction
The VISCA™/RS–232 control protocol, cont...
NOTE: Some VISCA™ commands do not apply to the PrecisionHD 1080p2.5x/4x/4x S2 cameras.
Camera commands, continued...
Command Command Packet
Mirror_On 8x 01 04 61 02 ff
Mirror_Off 8x 01 04 61 03 ff
Flip_On 8x 01 04 66 02 ff
Flip_Off 8x 01 04 66 03 ff
Gamma_Auto 8x 01 04 51 02 ff
Gamma_Manual 8x 01 04 51 03 ff
Gamma_Direct 8x 01 04 52 0p 0q 0r 0s ff
MM_Detect_On 8x 01 50 30 01 ff
MM_Detect_Off 8x 01 50 30 00 ff
Call_LED_On 8x 01 33 01 01 ff
Call_LED_Off 8x 01 33 01 00 ff
Call_LED_Blink 8x 01 33 01 02 ff
Power_LED_On 8x 01 33 02 01 ff
Power_LED_Off 8x 01 33 02 00 ff
IR_Output_On 8x 01 06 08 02 ff
IR_Output_Off 8x 01 06 08 03 ff
D14640.12 Cisco Telepresence PrecisionHD Camera User Guide TC6.2, August 2013.
The Physical Interface Connecting the Camera
Comments
Sony calls this CAM_LR_Reverse. RR
(FT/AT mirror command).
The "xConfiguration Cameras Camera
[1..n] Mirror: Auto" (supported by the
Codec C-series) do not apply to the
PrecisionHD 1080p 4x.
Sony calls this CAM_ImgFlip.
The "xConfiguration Cameras Camera
[1..n] Flip: Auto" (supported by the
Codec C-series) do not apply to the
PrecisionHD 1080p 4x.
Gamma mode. Default uses gamma
table 4.
pqrs: Gamma table to use in manual
mode. Range 0-7.
Turn on the Motor Moved Detection
(camera recalibrates if touched)
Turn off the Motor Moved Detection
(camera does not recalibrate if
touched)
Refers to orange LED on top of the
camera. It is always off at startup.
Green power LED. If switched to off
and stored to startup profile, it is
always off.
See IR push message.
30
Daisy Chaining
Command Command Packet
IR_CameraControl_On 8x 01 06 09 02 ff
IR_CameraControl_Off 8x 01 06 09 03 ff

PTZF - movement commands

Command Command Packet
Zoom_Stop 8x 01 04 07 00 ff
Zoom_Tele 8x 01 04 07 2p ff
Zoom_Wide 8x 01 04 07 3p ff
Zoom_Direct 8x 01 04 47 0p 0q 0r 0s ff
ZoomFocus_Direct 8x 01 04 47 0p 0q 0r
0s
0t 0u 0v 0w ff
Focus_Stop 8x 01 04 08 00 ff
Focus_Far 8x 01 04 08 2p ff
Focus_Near 8x 01 04 08 3p ff
Focus_Direct 8x 01 04 48 0p 0q 0r 0s ff
* Does not apply to PrecisionHD 1080p2.5x/4x/4x S2 cameras
Video Output Format Appendices Appendices
Comments
Lets the up/down/left/right/zoom+/-
on the IR remote control the camera
directly. Those keycodes are sent to
the controller if the IR Output is on.
Comments
p = speed parameter,
a (low) to b (high)
pqrs: zoom position
pqrs: zoom position
tuvw: focus position
p = speed parameter,
a (low) to b (high)
pqrs: focus position
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
User Guide