Inquiries - Cisco PrecisionHD 1080p12x User Manual

Cisco TelePresence PrecisionHD Camera
Contents Introduction
The VISCA™/RS–232 control protocol, cont...
NOTE: Some VISCA™ commands do not apply to the PrecisionHD 1080p2.5x/4x/4x S2 cameras.

Inquiries

Command Command Packet
CAM_ID_Inq 8x 09 04 22 ff
CAM_SWID_Inq 8x 09 04 23 ff
CAM_HWID_Inq 8x 09 04 24 ff
Zoom_Pos_Inq 8x 09 04 47 ff
Focus_Pos_Inq 8x 09 04 48 ff
Focus_Mode_Inq 8x 09 04 38 ff
PanTilt_Pos_Inq 8x 09 06 12 ff
Power_Inq 8x 09 04 00 ff
WB_Mode_Inq 8x 09 04 35 ff
WB_Table_Inq 8x 09 04 75 ff
AE_Mode_Inq 8x 09 04 39 ff
Backlight_Mode_Inq 8x 09 04 33 ff
Mirror_Inq 8x 09 04 61 ff
Flip_Inq 8x 09 04 66 ff
D14640.12 Cisco Telepresence PrecisionHD Camera User Guide TC6.2, August 2013.
The Physical Interface
Response
Resp: 90 50 zz xx 00 yy ff
Only zz, which identifies the camera, is relevant. zz
= 0x50 for this camera.
Resp: y0 50 [1-125 bytes ASCII SWID] ff. Never
route this message through Sony cameras.
The response is the Module Serial Number stored
in EEPROM. The number is converted to ASCII :
y0 50 [12 bytes ASCII HWID] ff.
Resp: y0 50 0p 0q 0r 0s ff
pqrs: zoom position
Resp: y0 50 0p 0q 0r 0s ff
pqrs: focus position
Resp: y0 50 0p ff
p=2: Auto, p=3: Manual
Resp: y0 50 0p 0q 0r 0s 0t 0u 0v 0w ff
pqrs: pan position tuvw:
tilt position
Resp: y0 50 0p ff
p=2: On, p=3: Off
Resp: y0 50 0p ff
p=0: Auto , p=6: Table manual
Resp: y0 50 0p 0q 0r 0s ff
pqrs: Table used if table mode is on.
Resp: y0 50 0p ff
p=0: Auto, p=3: Manual
Resp: y0 50 0p ff
p=2: On, p=3: Off
Resp: y0 50 0p ff
p=2: On, p=3: Off
Whether the video is flipped or not.
Resp: y0 50 0p ff
p=2: On , p=3: Off
Connecting the Camera Daisy Chaining
Command
Gamma_Mode_Inq
Gamma_Table_Inq
Call_LED_Inq
Power_LED_Inq
Video_System_Inq
DIP_Switch_Inq *
IR_Output_Inq
ALS_RGain_Inq *
ALS_BGain_Inq *
ALS_GGain_Inq *
ALS_WGain_Inq *
Up side down_Inq *
* Does not apply to PrecisionHD 1080p2.5x/4x/4x S2 cameras
32
Video Output Format
Command Packet
8x 09 04 51 ff Resp: y0 50 0p ff
p=2: Auto, p=3: Manual
8x 09 04 52 ff Resp: y0 50 0p 0q 0r 0s ff
pqrs: Gamma table in use if on manual mode.
8x 09 01 33 01 ff Resp: y0 50 0p ff
p=2: On, p=3: Off, p=4: Blink
8x 09 01 33 02 ff Resp: y0 50 0p ff
p=2: On, p=3: Off
8x 09 06 23 ff y0 50 0p 0q 0r 0s ff
pqrs=video mode currently being output on the
HDMI port. See chapter on DIP switches.
8x 09 06 24 ff y0 50 0p 0q 0r 0s ff pqrs contains the bit pattern
of the DIP switch. See chapter on DIP switches.
8x 09 06 08 ff Resp: y0 50 0p ff
p=2: On, p=3: Off
8x 09 50 50 ff Ambient Light Sensor Resp: y0 50 0p 0q 0r 0s 0t
0u 0v 0w ff
pqrstuv=32 bit unsigned integer, relative gain
value. The integration time is a constant set in the
camera SW.
8x 09 50 51 ff
8x 09 50 52 ff
8x 09 50 53 ff
8x 09 50 70 ff Resp: y0 50 0p ff
p=0: Camera is upright.
p=1: Camera is upside down.
Copyright © 2010–2013 Cisco Systems, Inc. All rights reserved.
User Guide
Appendices Appendices
Response