Software Upload Commands; Debug Commands For Cisco Cameras; Other Commands - Cisco PrecisionHD 1080p 12X User Manual

Cisco TelePresence PrecisionHD Camera
Contents Introduction
The VISCA™/RS–232 control protocol, cont...

Software upload commands

The CRC algorithm used, is the same as in the XModem protocol. CRC for the last data packet is
only calculated for the actual data bytes in the packet. Pad last packet with 0x00 so that the data
section is 256 bytes long. The PacketID counter starts at 0.
Command set Command packet
SW start 8x 01 50 a2 0p 0q
0r 0s 0t 0u 0v 0w ff
SW end 8x 01 50 a1 ff
SW abort 8x 01 50 a3 ff
SW packet 8x a0 pp qq rr ss
[256 bytes data]
D14640.04 PrecisionHD 1080p-720p Camera User Guide
© 2010-2011 Cisco Systems, Inc. All rights reserved.
The physical interface
Comments
pqrstuvw = size, pq=LSB Returns y050ff if
ok.
Fatal errors: Returns y06006ff if upload
already in progress. Returns y06007ff if
unable to access the flash.
Sent after last SW packet, instructs camera
to verify new application. Command may take
up to 30 seconds to complete.
Returns y050ff if ok. Issue a camera reboot
to activate new software.
Returns y06008ff if verification of sw failed.
Abort sw upload in progress
ppqq = 16 bit packet id, pp=LSB
rrss = 16 bit CRC, rr=LSB
Returns y0 50 ff if packet ok.
-> send next one.
Returns y0 60 09 ff if crc error -> retransmit
packet.
Returns y0 60 0a ff if id error
-> retransmit packet
Fatal errors:
y0 60 0b ff not in upload mode
y0 60 0c ff error writing data to flash
NOTE: Entire message after 8x a0... is raw
data, so it may contain 0xff. Header is kept as
short as possible. Never route this message
through Sony cameras.
, July 2011
.
Connecting the camera Video output formats
INFO: Some VISCA™ commands do not apply to the PrecisionHD 1080p 4X camera.

Debug commands for Cisco cameras

NOTE: Never route these messages through Sony cameras. They are provided for debugging on
the PrecisionHD cameras only, and do not conform to the Visca length requirements.
Command set
CAM_PingPong_
Reset *
CAM_Ping *
CAM_Stdin *
CAM_Debug_
Mode *

Other commands

Command set
CAM_Boot 8x 01 42 ff
CAM_Speed 8x 01 34 0p ff
*
Do not apply to PrecisionHD 4X camera
25
PrecisionHD Camera User guide
Daisy chaning
Command packet
8x ae ff Reset ping ctr to 0.
8x af 0p 0q 0r 0s pqrs = Pingval. Camera will respond with
[256 bytes data] ff OK if correct pingval received. Increase ctr
with 1 for next packet. Data section will be
dumped to stdout if it fails.
8x a4 [0-256 bytes Send command to the command
stdin] 00 ff interpreter.
8x 01 39 0q ff q=0: Debug mode off.
q=1: Debug mode on. Camera will send
stdout as visca messages in the following
format:
y0 50 [0-256 bytes stdout] 00 ff
Command packet
Reboot the camera. This will also reset serial
speed to 9600.
p=0: Serial speed 9600. p=1: Serial speed
115200. Reply will be sent before the speed
switch takes place. Please wait 20ms after ok
before sending new commands.
Appendices Appendices
Comments
Comments
www.cisco.com