Bru-Sf10 Hd Optical Multiplex Unit (Not Supplied); Power Switch - Sony BRC-H900 Operating Instructions Manual

BRU-SF10 HD Optical Multiplex
Unit (not supplied)
Front
1 2 3 4 5
ON/STANDBY
LINK
ALARM
DATA MIX SD
OFF ON
8
A Power switch
Turns on/off the power of this unit. Turn on the
power of the BRC-H900 camera before you turn on
this unit.
B Power indicator
Off: The unit's power switch is turned off.
Lit orange: The unit is starting up or in sleep mode.
Lit green: The unit is in normal operation.
C LINK indicator
Lit green: The optical fiber connection between the
unit and the camera is normal. (The indicator
lights in green after the system starts up.)
Lit red: Check for the following.
• The BRU-SF10 is not properly connected to
the camera via optical fiber cable. Check the
connections, and restart the unit.
• Image frequency settings for the camera and
the BRU-SF10 are different. Check the
settings after turning off the power, then
restart the unit.
• The camera may be unable to start properly
due to the AC adaptor being improperly
connected to the DC IN connector on the
camera. Check that the camera is turned on.
D ALARM indicator
Lit red: Check for the following.
• The BRU-SF10 is not properly connected to
the camera via an optical fiber cable. Check
the connections, then restart the unit.
• Image frequency settings for the camera and
the BRU-SF10 are different. Check the
settings after turning off the power, then
restart the unit.
• The camera may be unable to start properly
due to the AC adaptor being improperly
connected to the DC IN connector on the
camera. Check that the camera is turned on.
6
1 2 3 4 5 6 7
7
1080i 59.94 RS232C 9600bps
720p 50 RS422 38400bps
HD OPTICAL MULTIPLEX UNIT
• An unsupported optional interface card is
inserted in the card slot of the BRU-SF10.
Remove the card after turning off the power,
then restart the unit.
Off: The unit is in normal operation.
E SD indicator
This indicator lights when a BRBK-SA1 optional
interface card is installed, or when a BRBK-HSD2
is installed and its rear switch is set to SD.
F Camera ID indicators
The number for the current camera address lights in
orange.
For details on setting the camera address, see
"Q VISCA FUNCTION switches" on page 26.
G Status indicators
The current communication format, baud rate, and
video format settings light in green.
For details on configuring these settings, see
"Q VISCA FUNCTION switches" on page 26.
H DATA MIX switch
When the SD indicator is lit, set this switch to ON
to overlap the menu display with the SD image
signals from any installed BRBK-SA1 and
BRBK-HSD2 interface card on which the rear
switch is set to SD.
Set this switch to OFF to hide the menu display.
Rear
9 0 qa qs qd qf
IN OUT
EXT SYNC RGB/COMPONENT
CAMERA
ql
I CAMERA connector
Connect to the optical connector of the BRBK-SF1
HD Optical Multiplex Card installed in the
BRC-H900 camera using the CCFC-S200 Optical
Fiber Cable.
A dustproof cap is attached at the factory.
Do not remove this cap if you do not intend to
connect an optical fiber cable. Dustproof caps are
also attached to the BRBK-SF1 and CCFC-S200.
Do not remove these caps when the connectors are
not in use.
J EXT SYNC IN connector
Accepts external video sync signals.
qg qh
IN OUT
1 2 3 4 5 6 7 8 9
VISCA RS232C
VISCA RS422
AUDIO OUT
L
FUNCTION
1
R
10
DC 12V
qk qj
Location and Function of Parts
25
GB