Page 1
HD 3CMOS COLOR VIDEO CAMERA BRC-Z700 HD/SD-SDI OUTPUT CARD BRBK-HSD1 HD OPTICAL MULTIPLEX CARD BRBK-MF1 SERVICE MANUAL 1st Edition (Revised 1)
Page 2
Ce manual est destiné uniquement aux personnes compétentes en charge de l’entretien. Afin de réduire les risques de décharge électrique, d’incendie ou de blessure n’effectuer que les réparations indiquées dans le mode d’emploi à moins d’être qualifié pour en effectuer d’autres. Pour toute réparation faire appel à une personne compétente uniquement. BRC-Z700...
Related manuals In addition to this Service Manual the following manual is provided..“Operating Instructions” BRC-Z700 (supplied with the BRC-Z700) This manual is necessary for application and operation of the BRC-Z700..“Operating Instructions” BRBK-HSD1 (supplied with the BRBK-HSD1) This manual is necessary for application and operation of the BRBK-HSD1.
D, E, F, and G. Screw cover (left) 2.6 x 6 (large) Outer cover (right) Portion A 2.6 x 6 (large) Screw cover (right) Hook Portion A Screw cover (right) Tool such as precision screwdriver 5. To install, reverse the removal procedure. BRC-Z700...
PSW2.6 x 6 (large) Inner cover (front) assembly 4. To install, reverse the removal procedure. When attaching the inner cover (front) assembly, be careful not to catch the two tapes (A) and tape (L53) inside the tilt chassis assembly. BRC-Z700...
(upper) with the When attaching the inner cover (rear), be careful not to hole in the rear of the camera cover (lower). catch the tape (A) inside the tilt chassis assembly. BRC-Z700...
Camera cover (lower) 8. To install, reverse the removal procedure. 8. To install, reverse the removal procedure. When attaching the front cabinet assembly, align the projections of the camera cover (lower) with the holes of the front cabinet assembly. BRC-Z700...
1. Remove the two screws with stopper, then remove the assembly. HD blank panel assembly. Screws with stopper HD blank panel assembly Base plate assembly 2. To install, reverse the removal procedure. PSW3 x 8 2. To install, reverse the removal procedure. BRC-Z700...
The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful. CN7001 CN7002 Rear panel assembly Flexible flat cables SW-1383 board PSW2.6 x 6 7. To install, reverse the removal procedure. BRC-Z700...
. Part number: 7-621-759-40 +PSW2.6 x 6 Part name: In the illustration of this section, this screw is described as PSW2.6 x 6 (large). . Part name: Tape (A) Part number: 3-080-272-01 Replace the removed tape (A) with the new tape (A). BRC-Z700...
Page 16
15. Remove the T sheet, two wave washers, gear holder AD-181 board (T), parallel pin and gear (T). Tightening torque: 1.5 N.m KANIME tool Wave holder (T) Parallel pin T sheet Gear (T) Gear holder (T) Wave washers Wave holder (T) BRC-Z700...
Camera board chassis BSW2 x 5 Chassis reinforcing plate Prism assembly Lens assembly 2 x 5 2 x 5 14. To install, reverse the removal procedure. BRC-Z700...
8. Remove the two screws (PSW2.5 x 5), then remove the tilt motor. Tape (A) Harness 2.5 x 5 Damper washers B2.6 x 14 DR-623 board CN3004 Tilt motor Motor mounting plate 2.5 x 5 B2.6 x 14 Damper washers BRC-Z700...
(P). Damper washer 7. Remove the two screws (PSW2.5 x 5), then remove the pan motor. Motor pulley Pan motor Pulley (P) Timing belt B2.6 x 14 Motor mounting Damper plate (P) washer PSW2.5 x 5 BRC-Z700...
When attaching the DC fan, attach it with the label (camera block) side placed on the EXP chassis assembly side. Label side 14. To install, reverse the removal procedure. When attaching the DC fan, attach it with the label side placed upward. BRC-Z700...
Tape (L40) Flexible flat cable tube. Ferrite bead 16. Remove the two tapes (A) [*2], then remove the SY-354 board Harness tube flexible flat cable from the two hooks of the harness guide (lower). BRC-Z700...
Harness tube (Refer to Section 1-2-2.) 3. Remove the inner cover (front) assembly. CC-97 board (Refer to Section 1-2-3.) 4. Remove the inner cover (rear). (Refer to Section 1-2-4.) 5. Remove the camera cover (upper). (Refer to Section 1-2-5.) BRC-Z700...
LVDS harness assembly 5. To install, reverse the removal procedure. 23. To install, reverse the removal procedure. Replace the removed tape (A) and tape (L40) with the new tape. Replace the removed tape (L40) with the new tape (L40). 2-10 BRC-Z700...
3. Remove the SY-354 board. (Refer to Section 2-2-1.) 4. Remove the EXP chassis assembly. (Refer to steps 4 and 5 in Section 2-2-2.) 5. Disconnect the LVDS harness assembly from the connector (CN701) on the CC-97 board. 2-11 BRC-Z700...
5. Remove the tape (A), then disconnect the flexible flat cable from the connector (CN4001) on the TSI-59 board. 6. Remove the screw, then remove the TSI-59 board. Flexible flat cable Tape (A) TSI-59 board Flexible flat cable CN4001 2.6 x 6 Tape (A) 2-13 BRC-Z700...
DR-623 board CN3003 IR-41 board 2.6 x 6 CN3004 CN3002 CN3001 Flexible flat cables 4. To install, reverse the removal procedure. 5. To install, reverse the removal procedure. Replace the removed tape (A) with the new tape (A). 2-14 BRC-Z700...
5. Remove the camera cover (upper). (Refer to Section 1-2-5.) 6. Remove the front cabinet assembly. (Refer to Section 1-2-6.) 7. Remove the two screws, then remove the LED-468 board. LED-468 board BTP2 x 6 8. To install, reverse the removal procedure. 2-15 BRC-Z700...
Fixture cable J-6402-620-A System FPGA writing software QURTUS II PROGRAMMER 7.2 SP1 or higher made by Altera Camera FPGA writing software iMPACT in Xilinx ISE 8.2 made by Xilinx CPU writing software Flash Development Toolkit made by Renesas Technology BRC-Z700...
3-1-2. Connection AC adaptor AD-181 board AC-IN CN1201 BRC-Z700 Personal computer DC-IN Platform cable Fixture cable VISCA IN VISCA cable RS-232C RGB/COMPONENT D-sub 15-pin 5 BNC HD monitor Card slot S004 S005 S006 Extension board BNC cable EX-1089 CN003 Frequency counter...
Page 33
XXX and XX mean the version number and release number. 2. Click the [Next] button. 3. Select language, then click the [Next] button. 4. After confirming the contents of the license agreement, select “I accept the terms of the license agreement”. Then click the [Next] button. BRC-Z700...
Page 34
5. Click the [Next] button. 6. Click the [Next] button. 7. Confirm the destination folder, then click the [Next] button. To change the destination folder, click the [Browse...] button and change. BRC-Z700...
Page 35
8. Click the [Install] button. 9. Click the [Finish] button. (Installation is completed.) Connecting the fixture cable Connect the fixture cable and connector of the platform cable as shown in the illustration. Obverse side Reverse side BRC-Z700...
4. Using the [(]/[)] button of an infrared remote controller, adjust so that the value of a frequency counter satisfies specification B. Specification B: 33716.284 ± 0.100 Hz m . To increase the value, press the [(] button. . To decrease the value, press the [)] button. 5. Turn off the power of this unit. BRC-Z700...
3. Press the [*] button of an infrared remote controller to display “EVR_CAM no:009” and adjust the display to data:097 using a [(] button. 4. Turn off the power of this unit. SYNC signal is output from VD ch. BRC-Z700...
7. Set as below, then click the [Next] button. Enter the CPU crystal frequency for the selected device: 25.0000 Enter the clock mode for the selected device: NONE Select the multiplier for the Main clock frequency (CKM): Select the multiplier for the Peripheral clock frequency (CKP): (Blank) BRC-Z700...
Page 39
X.XX means the version of the CPU writing tool. Writing 1. Set the switches on extension board EX-1089 as described below. S002: OPE S004 S005 S006 S003: WRITE S004: L S005: L S003 S002 S001 S006: L WRITE NORMAL BRC-Z700...
Creating the workspace The workspace creating is required only first time. 1. Start the CPU writing software by PC. 2. Select “Create a new project workspace”, then click the [OK] button. 3. Enter “BRC-Z700VENUSCPU” in Workspace Name box. 3-10 BRC-Z700...
Page 41
Kernel already running: un-check Recommended Speeds: selected Use default: check-mark 9. Confirm the settings set as below, then click the [Finish] button. Protection: Automatic Messaging: Advanced The project workspace “BRC-Z700VENUSCPU” is created. X.XX means the version of the CPU writing tool. 3-11 BRC-Z700...
Page 42
File name: xxxx.mot 8. Select “Device” → “Download xxxx.mot” from a menu bar. Writing operation is started. 9. Select “Device” → “Disconnect” from a menu bar. Connection with this unit is disconnected. 10. Turn off the power of this unit. 3-12 BRC-Z700...
7. Select “Generic BOOT Device” in Select Device box, then click the [Next] button. 8. Select the COM port of PC in Select port box, then click the [Next] button. 9. Confirm this unit is connected properly and powered, then click the [OK] button. 3-13 BRC-Z700...
Page 44
Enter the clock mode for the selected device: Select the multiplier for the Main clock frequency (CKM): Select the multiplier for the Peripheral clock frequency (CKP): 4 12. Confirm the settings set as below, then click the [Next] button. Recommended Speeds: selected Use default: check-mark 3-14 BRC-Z700...
Page 45
File name: xxx.mot 8. Select “Device” → “Download xxx.mot” from a menu bar. Writing operation is started. 9. Select “Device” → “Disconnect” from a menu bar. Connection with this unit is disconnected. 10. Turn off the power of this unit. 3-15 BRC-Z700...
S006: L WRITE NORMAL 2. Turn on the power of this unit. 3. Start System FPGA writing software using PC. 4. Select the “ActiveSerial Programming” in “Mode”. 5. Click the [Hardware|Setup...] button. The Hardware Setup window is displayed. 3-16 BRC-Z700...
Page 47
8. Click the [OK] button. 9. Confirm that the set cable is displayed in Currently selected Hardware, then click the [Close] button. 10. Confirm that the settings is as below. Hardware Setup:Cable name set in steps 6 and 7 Mode: ActiveSerial Programming 3-17 BRC-Z700...
Page 48
13. Place the check marks in the check boxes of “Program/Configure” and “Verify”. 14. Click the [Start] button. 15. Confirm that “Ended Programmer operation” is displayed in System tab. 16. Turn off the power of this unit and disconnect the FPGA write cable. 3-18 BRC-Z700...
When no project is created, click the [Cancel] button. When no project is created, double-click the “Direct SPI Configuration” in the Flows sub window on the top left corner of screen. 6. Right-click on main area, then select “Add SPI Device...”. 3-19 BRC-Z700...
Page 50
9. Click the Program icon on the tool bar. Programming Properties window is displayed. 10. Click the [OK] button. 11. Confirm that “Programming Succeeded” is displayed. 12. Turn off the power of this unit. 13. Turn off the switch (S1201) on the AD-181 board. 3-20 BRC-Z700...
Therefore, specified parts should be used in the case of replacement. 2. Standardization of Parts Some repair parts supplied by Sony differ from those used for the unit. These are because of parts common- ality and improvement. 3. Stock of Parts Parts marked with “o”...
4-2. Exploded Views PSW2.6 x 6 2.6 x 8 PSW2.6 x 6 BTP2.6 x 8 PSW2.6 x 6 2.6 x 6 2.6 x 6 PSW2.6 x 6 2.6 x 6 PSW2.6 x 6 PSW2.6 x 6 PSW2.6 x 6 BRC-Z700...
Page 53
3-287-212-02 s COVER (RIGHT), OUTER 3-287-213-02 s COVER (LEFT), OUTER 3-287-214-01 s COVER (RIGHT), SCREW 3-287-215-01 s COVER (LEFT), SCREW 3-746-217-02 s SCREW, TAPPING(B),SPECIAL HEAD 3-986-877-01 s +PSW2.6X6 7-621-759-40 s +PSW, 2.6X6 7-685-534-19 s SCREW +BTP 2.6X8 TYPE2 N-S BRC-Z700...
Page 54
Tilt Chassis Block E-3.0 B2.6 x 14 B2.6 x 14 BRC-Z700...
Page 55
3-986-892-01 s BEARING T 3-986-898-01 s WASHER (T) 3-990-384-01 s SPRING,SHIELD 4-382-854-01 s SCREW (M3X8), P, SW (+) 3-986-877-01 s +PSW2.6X6 7-621-775-70 s SCREW +B 2.6X14 7-623-710-57 s WASHER 10, WAVE TYPE 7-624-106-04 s STOP RING 3.0, TYPE -E BRC-Z700...
Page 56
1-834-897-11 s CABLE,FLEXIBLE FLAT (20 CORE) 3-863-696-11 s +BSW M2 1-963-577-41 s HARNESS (COAXIAL CABLE) 3-986-877-01 s +PSW2.6X6 2-279-715-11 s RIVET, NYLON 3-986-893-02 s SENSOR SHUTTER T 3-073-686-01 s SCREW (M2X2.5) 3-080-204-31 s SCREW, TAPPING, P2 7-621-759-65 s +PSW, 2.6X8 7-621-759-90 s +PSW, 2.6X14 BRC-Z700...
Page 57
CN4203 1-573-370-61 s CONNECTOR, FFC/FPC (ZIF) 30P F4001 CN4204 1-784-424-61 s CONNECTOR, FFC/FPC (ZIF) 51P CN4205 1-573-360-61 s CONNECTOR, FFC/FPC (ZIF) 20P F4001 1-576-874-11 o FUSE, MICRO (1608 TYPE) (2.5A/32V) F4002 1-576-913-21 s FUSE, MICRO (1608 TYPE) (1.6A/36V) F4002 BRC-Z700...
Page 58
1-573-370-51 s CONNECTOR, FFC/FPC (ZIF) 30P CN3301 1-580-056-21 s PIN, CONNECTOR (SMD) 3P CN3303 1-766-866-51 s CONNECTOR, FFC/FPC 6P CN3305 1-580-055-21 o PIN, CONNECTOR (SMD) 2P CN3501 1-784-424-61 s CONNECTOR, FFC/FPC (ZIF) 51P CN3502 1-573-360-61 s CONNECTOR, FFC/FPC (ZIF) 20P BRC-Z700...
Page 59
3-290-546-01 s TAPE (L40) 3-715-526-01 o WASHER (M3) 3-986-877-01 s +PSW2.6X6 4-043-045-01 s FOOT 4-382-854-01 s SCREW (M3X8), P, SW (+) 4-382-854-21 s SCREW (M3X14), P, SW (+) 1-400-260-11 s BEAD, FERRITE 3-287-505-01 s TAPE (L53) 7-682-546-09 s SCREW +B 3X5 BRC-Z700...
Page 60
3-287-874-01 s DAMPER (M), MOTOR 3-608-891-01 o POST,HEXAGON 3-986-847-01 s FLANGELESS BALL BEARING 3-986-877-01 s +PSW2.6X6 3-986-900-01 s WASHER, P 3-990-382-01 s WASHER, WAVE 4-672-493-01 s COVER (SC) 7-621-775-70 s SCREW +B 2.6X14 7-624-106-04 s STOP RING 3.0, TYPE -E 4-10 BRC-Z700...
Page 61
7-682-947-01 s SCREW +PSW 3X6 BRBK-MF1 PSW3 x 6 Part No. SP Description A-1444-777-A s MOUNTED CIRCUIT BOARD, MX-118 1-562-941-21 s JACK, PIN 1-562-941-31 s JACK, PIN 1-789-401-11 s MODULE,OPTICAL (SFP) 3-986-877-01 s +PSW2.6X6 7-682-947-01 s SCREW +PSW 3X6 4-11 BRC-Z700...
1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C718 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C1236 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C719 1-107-826-91 s CAP, CHIP CERAMIC 0.1MF B C1237 1-100-567-81 s CAP,CHIP CERAMIC 0.01MF B 1005 4-12 BRC-Z700...
Page 63
1-165-989-91 s CAP, CERAMIC 10MF (2012) C1603 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C2246 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C1802 1-165-989-91 s CAP, CERAMIC 10MF (2012) C2247 1-164-935-81 s CAP, CHIP CERAMIC 470PF B 1005 4-13 BRC-Z700...
Page 64
1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C8045 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C8104 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C8046 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C8105 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 4-14 BRC-Z700...
Page 65
6-709-646-01 s IC TLC2933AIPWR FB240 1-414-864-21 s FERRITE, EMI (SMD) (1608) IC1215 8-759-564-49 s IC TC7W53FU(TE12R) IC1216 8-759-564-49 s IC TC7W53FU(TE12R) FB241 1-414-864-21 s FERRITE, EMI (SMD) (1608) FB701 1-500-237-22 s BEAD, FERRITE (CHIP) (1608) IC1217 8-759-564-49 s IC TC7W53FU(TE12R) 4-15 BRC-Z700...
Page 66
1-218-929-81 s RES, CHIP 10 L8002 1-414-398-41 s INDUCTOR (SMD) 10.0UH R426 1-218-929-81 s RES, CHIP 10 R427 1-218-929-81 s RES, CHIP 10 Q001 8-729-928-82 s TRANSISTOR DTC144EE-TL Q002 8-729-928-82 s TRANSISTOR DTC144EE-TL R428 1-218-929-81 s RES, CHIP 10 4-16 BRC-Z700...
Page 67
1-218-990-81 s CONDUCTOR, CHIP (1005) R512 1-218-929-81 s RES, CHIP 10 R910 1-218-965-81 s RES, CHIP 10K R513 1-218-929-81 s RES, CHIP 10 R911 1-218-965-81 s RES, CHIP 10K R701 1-218-941-81 s RES, CHIP 100 R912 1-218-965-81 s RES, CHIP 10K 4-17 BRC-Z700...
Page 68
1-218-941-81 s RES, CHIP 100 R970 1-218-929-81 s RES, CHIP 10 R1264 1-218-941-81 s RES, CHIP 100 R971 1-218-929-81 s RES, CHIP 10 R1265 1-218-941-81 s RES, CHIP 100 R972 1-218-929-81 s RES, CHIP 10 R1266 1-218-941-81 s RES, CHIP 100 4-18 BRC-Z700...
Page 69
1-208-863-81 s RES, CHIP 100 (1005) R1833 1-218-827-91 s RES, CHIP 150 (1608) R1464 1-208-863-81 s RES, CHIP 100 (1005) R1834 1-218-827-91 s RES, CHIP 150 (1608) R1465 1-208-863-81 s RES, CHIP 100 (1005) R1835 1-218-827-91 s RES, CHIP 150 (1608) 4-19 BRC-Z700...
Page 70
1-218-965-81 s RES, CHIP 10K R2264 1-218-990-81 s CONDUCTOR, CHIP (1005) R2343 1-218-965-81 s RES, CHIP 10K R2265 1-218-965-81 s RES, CHIP 10K R2344 1-218-990-81 s CONDUCTOR, CHIP (1005) R2266 1-218-965-81 s RES, CHIP 10K R2351 1-218-965-81 s RES, CHIP 10K 4-20 BRC-Z700...
Page 71
1-208-863-81 s RES, CHIP 100 (1005) R8025 1-208-863-81 s RES, CHIP 100 (1005) R8026 1-208-863-81 s RES, CHIP 100 (1005) R8027 1-208-863-81 s RES, CHIP 100 (1005) R8028 1-208-863-81 s RES, CHIP 100 (1005) R8029 1-208-863-81 s RES, CHIP 100 (1005) 4-21 BRC-Z700...
Page 72
1-218-990-81 s CONDUCTOR, CHIP (1005) R5607 1-218-990-81 s CONDUCTOR, CHIP (1005) R5608 1-218-990-81 s CONDUCTOR, CHIP (1005) R5609 1-218-941-81 s RES, CHIP 100 R5616 1-218-990-81 s CONDUCTOR, CHIP (1005) R5617 1-218-990-81 s CONDUCTOR, CHIP (1005) R5618 1-218-990-81 s CONDUCTOR, CHIP (1005) 4-22 BRC-Z700...
Page 73
1-216-809-91 s RES, CHIP 100 (1608) R5009 1-218-973-81 s RES, CHIP 47K R3009 1-216-809-91 s RES, CHIP 100 (1608) R3012 1-218-990-81 s CONDUCTOR, CHIP (1005) R3013 1-218-990-81 s CONDUCTOR, CHIP (1005) R3016 1-218-990-81 s CONDUCTOR, CHIP (1005) R3017 1-218-990-81 s CONDUCTOR, CHIP (1005) 4-23 BRC-Z700...
Page 74
1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 C079 1-165-989-91 s CAP, CERAMIC 10MF (2012) C745 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 C080 1-125-777-81 s CAP, CHIP CERAMIC 0.1MF B 1005 C746 1-112-015-91 s CAP, CHIP CERAMIC 47MF B 3225 4-24 BRC-Z700...
Page 75
6-501-817-01 s DIODE MA2J1110GLS0 IC903 6-703-721-01 s IC TPS54310PWPR D012 8-719-421-70 s DIODE MA133-TX L001 1-416-510-21 s COIL, CHOKE 100UH D017 6-501-817-01 s DIODE MA2J1110GLS0 L002 1-416-344-21 s COIL, CHOKE 10UH D701 8-719-080-69 s DIODE M1FS4-4063 L003 1-414-754-91 s INDUCTOR 10.0UH 4-25 BRC-Z700...
Page 76
1-218-990-81 s CONDUCTOR, CHIP (1005) R018 1-218-941-81 s RES, CHIP 100 R125 1-218-990-81 s CONDUCTOR, CHIP (1005) R020 1-218-990-81 s CONDUCTOR, CHIP (1005) R126 1-218-990-81 s CONDUCTOR, CHIP (1005) R022 1-218-953-81 s RES, CHIP 1.0K R127 1-218-965-81 s RES, CHIP 10K 4-26 BRC-Z700...
Page 77
1-218-990-81 s CONDUCTOR, CHIP (1005) R187 1-218-965-81 s RES, CHIP 10K R255 1-218-990-81 s CONDUCTOR, CHIP (1005) R188 1-218-965-81 s RES, CHIP 10K R260 1-218-990-81 s CONDUCTOR, CHIP (1005) R191 1-218-965-81 s RES, CHIP 10K R261 1-218-990-81 s CONDUCTOR, CHIP (1005) 4-27 BRC-Z700...
Page 78
1-218-949-81 s RES, CHIP 470 R748 1-218-953-81 s RES, CHIP 1.0K R749 1-218-965-81 s RES, CHIP 10K R750 1-216-825-91 s RES, CHIP 2.2K (1608) R752 1-218-977-81 s RES, CHIP 100K R753 1-218-977-81 s RES, CHIP 100K R754 1-218-973-81 s RES, CHIP 47K 4-28 BRC-Z700...