Table of Contents
Advertisement
Information Item
13. System information
and warnings
14. Time code indication
15. Chromatic aberration
compensation
16. Extender
17. Color temperature
18. Filter position
19. Dynamic range
stretcher mode
Adjustments and Settings for Recording : Viewfinder Screen Status Displays
80
Indication
SYSTEM ERROR-¢¢
TURN POWER OFF
CARD ERR ¢
REC WARNING
OVER MAX# CLIPS
TEMPORARY PAUSE
BACKUP BATT EMPTY
FAN STOP
WIRELESS-RF
EOM
BOS
EOS
CANNOT REC
CANNOT PLAY
COMM ERROR
TEXT MEMO
TEXT MEMO INVALID
MARK ON/OFF
SHOT MARK INVALID
UPDATING
USB DEVICE
USB HOST
THUMBNAIL OPEN
CLIP DISCONTINUED
TC REGEN
SLOT SELECT
SLOT SELECT INVALID
DIR NG CARD
SLOT1/2
RUN DOWN CARD
SLOT1/2
REAR XR AUTO
TCG
12:59:59:20
TCR
12:59:59:20
(V)UBG
AB CD EF 00
(V)UBR
12 34 56 78
CTL
–1:59:59:20
CAC
EX
¢.¢K
1 - 4
A - D
(blink)
DRS
Something abnormal is happening to the internal computer communications or
reference signal. No further recording or playback can be performed. ¢¢ is
replaced with an error code. For more information, see [Error Codes] (page 155).
P2 card has been removed while being accessed (recorded, played back, or
formatted), and subsequent operation is disabled.
An error has occurred while recording data to or playing data from a P2 card.
In the actual indication the ¢ is replaced by the slot number of the P2 card that
triggered the error.
Something abnormal is happening to video and/or audio being recorded.
Displayed when the maximum number of clips (1000) recorded to the P2 card
is exceeded.
There is a temporary halt in recording due to distortion in reference signals
such as during GENLOCK input.
Backup battery needs replacing.
The fan is locked and halted.
RF signal from the wireless receiver is degraded.
P2 card has no free space.
Playback position is at the start of all the clips.
Playback position is at the end of all the clips.
The P2 card is not recordable. Detailed information is provided on the
FUNCTION screen of MODE CHECK.
> [Displays in mode check only] (page 82)
Clip cannot be played back perhaps because no P2 card is loaded, or the P2
card contains no clips.
Displayed when disconnection between microcomputers continues for a
specified period or longer.
Text memo has been added.
Text memo has not been successfully added.
Shot mark been added or deleted. For information on shot marks, see [Shot
Mark Function] (page 46).
This is displayed when shot marks cannot be added.
Clip information is being updated. Playback operation disabled.
AJ-HPX3100 is in USB DEVICE mode. When communication is disabled, the
indication blinks.
Indicates that the camera-recorder is set to the USB HOST mode. When the
external hard disk is not successfully recognized, then the indication blinks.
Thumbnail is being manipulated.
Displayed when the consistency of the combined clip is disrupted and
subsequent recordings cannot be combined in the clip when recording in ONE
CLIP REC mode.
The RET button was pressed to regenerate the time code as the time code for
the last clip recorded on a P2 card.
This blinks while the recording slots of P2 cards are switched after pressing
the USER switch where the SLOT SEL function is assigned.
This is displayed if the recording slots of P2 cards cannot be switched when
the USER switch where the SLOT SEL function is assigned is pressed.
This is displayed when the recording starts or completes while a P2 card with
an irregular directory arrangement is inserted or data are recorded after
inserting an irregular P2 card.
This is displayed when the recording starts or completes with a P2 card on
which the maximum number of overwrites has been exceeded, or when data
is recorded after inserting such a P2 card.
The AUDIO IN switch is disabled because audio input automatically goes to
the rear XLR connector.
TCG (time code generator value)
TCR (time code reader value)
UBG VUBG (User bits generator value)
UBR VUBR (User bits reader value)
Displays CTL count.
Displayed when chromatic aberration compensation is activated
Lens extender used.
Color temperature assigned to A, B, and PRST of the WHITE BAL switch (this
is a value stored at AWB performance or a value set through the menu
option). The indication is not provided in ATW mode.
This indicates the position of the ND filter.
This indicates the position of the CC filter.
This indicates that the filter has not been set to a proper position.
This appears when the video level of a part with high brightness is
compressed, and the function stretching the dynamic range is selected.
Status
Advertisement
Table of Contents
