Advertisement
D. Using the K-1200 with a C-3000
For a "No CO" installation, a Viking C-3000 No CO controller can be used with the K-1200. Note, the K-1200 will need to be pro-
grammed on a separate CO line or use the Viking DLE-200B. The door strike can be controlled by the K-1200 or the internal relay
on the C-3000, just be sure to disable the door strike feature in the other unit. The keyless entry feature of the C-3000 can not be
used. If not using keyless entry codes, use the C-3000 to control the doorstrike. If using keyless entry codes (up to 50), use the K-
1200 to control the doorstrike. The K-1200 speed dial position should be programmed with the C-3000 line selection command "1"
to "12". (Refer to the C-3000 Technical Practice for more details).
120V AC
Model
K-1200
Notes: 1. In this application, the C-3000 keyless entry feature is not available. Use the keyless entry feature of the K-
1200 and wire both door strike relays in parallel. 2. The K-1200 will hang-up during the doorstrike activation.
P
r
o
g
r
a
m
m
P
r
o
g
r
a
m
m
A. Accessing The Programming Mode
The K-1200 Entry Controller can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU,
or a DLE-200B Line Simulator.
1. Accessing the Programming Mode with the Security Code
Step 1.
Move DIP switch 1 to the ON position (sets unit to answer incoming calls).
Step 2.
From a touch tone phone, call the line attached to the K-1200.
Step 3.
When the K-1200 answers, listen for the beep and then enter a "#" followed by the 6-digit security code (factory
set to 845464). A double beep should be heard indicating you have entered the programming mode.
2. Accessing the Programming Mode without the Security Code
Step 1.
Move DIP switch 1 to the ON position (sets unit to answer incoming calls).
Step 2.
Move DIP switch 4 to the ON position (incoming calls enter programming without security code, see section B).
Step 3.
From a touch tone phone call the line attached to the K-1200.
Step 4.
When the K-1200 answers, a double beep should be heard indicating you have entered the programming mode.
Step 5.
When finished programming, move DIP switch 4 back to the OFF position.
B. Security Code (memory location #47)
This six digit number can be used to access the programming mode. The security code has been factory set to 845464
(V-I-K-I-N-G). It is recommended that you change the security code to a personal 6 digit number. To change the secu-
rity code, access programming (see Programming section A). Enter six digits 0-9 followed by #47. If you have forgot-
ten your security code, follow the steps in Programming section A, 2. Accessing the Programming Mode Without
the Security Code). Note: The security code must be six digits in length and can NOT contain a , or #.
C. Keyless Entry Codes
The K-1200 can be programmed with up to 50 keyless entry codes. This feature allows a visitor to let themselves in by
entering a preprogrammed code on the K-1200 keypad. Each keyless code can contain from 1 to 6 digits and is pro-
grammed by entering the digits into any of the locations #50 to #99. To clear a location enter "#" followed by the posi-
tion number without any preceding number. The "," and "#" keys can also be used in the keyless codes by substitut-
ing "#20" and "#21" (respectively) when programming a keyless position.
VIKING
POWER
13.8 VAC
POSTAL
LOCK
INPUT
DIP
SWITCH
1 1 2 2
1 2 3
O
N
O
F
F
PWR
IN
USE
PROGRAM PHONE
Red
Green
i
n
g
i
n
g
MODEL C-3000
©
VIKING
ELECTRONICS
HUDSON, WI 54016
12 UNIT APARTMENT
ENTRY CONTROLLER MODULE
DOOR
DOOR
STRIKE
STRIKE
1
2
RJ21X
3 3 4 4 5 5 6 6 7 7
8 8
12
12 APARTMENT LINES IN/OUT
MULTI-MODULE
INTERCONNECTS
ENTRY
ENTRY
PHONE 1
PHONE 2
OUT
IN
Green
Red
Model C-3000
(not included)
120V AC
Model
K-1200
5
Advertisement
