Advertisement
D. Quick Programming Features
The K-1200 is programmed through the incoming phone line. The programming commands are structured so that
they do not interfere with the commands of a C-1000B controller.
Speed dial numbers ..................................................................................................
Door strike time in sec (factory 05, 00 =.5 sec)**........................................................
Door strike code (factory 6, no digits disables) ..........................................................
Maximum call time in min (factory 3, 0 = .5 min, no digits disables)** .......................
Maximum ring time in sec (factory 20, 00 disables)** ...............................................
Silence Time Out in sec (factory 10, 00 disables)** ..................................................
Talk/listen delay time in .1 sec (factory 2)** ...............................................................
Security code (factory 845464)** ...............................................................................
Keyless entry codes ..................................................................................................
,
Dial a (
) ..................................................................................................................
Dial a (#) ...................................................................................................................
Add a 4 second pause ..............................................................................................
Add a 1 second pause .............................................................................................
Second phone number selector ................................................................................
Normal dialing speed* ..............................................................................................
Fast dialing speed .....................................................................................................
Hang up on dial tone enable* ...................................................................................
Hang up on dial tone disable ....................................................................................
Reset all programming to factory default settings ...................................................
Hang up from programming ......................................................................................
*Factory settings
*** 45 digits maximum if two numbers are programmed in one memory location
Notes: 1. A single or double beep indicates a valid entry, three beeps indicate an error.
,
2. "
" or "#", pauses or second phone number selector occupy one digit of memory.
E. Speed Dial Numbers
The K-1200 Entry Controller can be programmed with up to twelve 46 digit numbers. Each number can also be programmed with
special features such as pauses, and the Touch Tones "
the speed dial positions #01 to #12 pertain to the corresponding button on the front of the K-1200. The button "0" uses position #10,
,
the "
" uses position #11 and the "#" uses position #12. To program a speed dial position, enter programming (see section A) then
enter the desired number followed by the selected position. To clear a position, only enter a "#" followed by the position number with
out any preceding number.
The K-1200 also has the capability to dial a second phone number if there is no answer or busy at the first number. This can be
used if the tenant wants the visitor to call their cell phone if they are not at home. To program a second number, be sure that posi-
tion #43 is programmed with the desired maximum ring time, then enter the first number to be dialed, followed by "#24". A single
beep should be heard. Next enter the second number to be dialed followed by "#" plus the memory location. The total number of
digits cannot exceed 46 for each position (45 digits if two numbers are programmed).
The following are examples of speed dial number entries:
To Program the K-1200 to...
...store 555-1234 at the first button position
...store a 9, a 1 second pause, then 333-4444 in the seventh button position
,
...store a 23
# in the eight position
...store a first number of 22 and a second number of 33 in the "#"
button position
F. Door Strike Time
The actual time the door strike relay is energized is controlled by location #40. The time can be set from 00 to 99 seconds, (an entry
of "00" gives 0.5 seconds). In order to use this feature, be sure the relay door strike code is set (see section H).
G. Maximum Call Time
In some installations, it maybe desirable to limit the length of the call to the tenant. This can be done by programming
position #42. The maximum call time can be set from 1 minute to 9 minutes by entering the appropriate number in posi-
tion #42. A "0" will yield a 30 second time. To disable the call timer enter "#42" without any preceding digit.
6
,
** Cannot contain "
" or "#" (see #20 and #21)
Enter Digits
0-46 digits***
2 digits
1-2 digits
1 digit
2 digits
2 digits
1 digit
6 digits
1-6 digits
#20
#21
#22
#23
#24
#30
#31
#32
#33
###
##7
,
" and "#". Each of the special characters count as a single digit. Each of
Step 1 (see section A)
Enter programming
Enter programming
Enter programming
Enter programming
- then - Enter Memory Location
then
#01 - #12
then
#40
then
#41
#42
then
then
#43
then
#44
then
#45
then
#47
#50 - #99
then
Step 2 - Enter Digits
5551234#01
9#233334444#07
23#20#21#08
22#24 (beep) 33#12
Advertisement
