NAPCO Gemini GEM-P3200 Installation Instructions Manual page 49

WI817C 08/00
Timeout
Specifies the length of time that an alarm, alert, or delay will remain active. Auxiliary Output Access Control Time, Abort-Delay
Time, and Chime Time must be programmed, or the feature will not activate. See Time Selection.
(1)
TIME
RESET OUTPUT
AUXILIARY OUTPUT
AUXILIARY OUTPUT
ACCESS CONTROL TIME
BURGLARY OUTPUT
PULSE-BURG OUTPUT
FIRE OUTPUT
ABORT DELAY
CHIME TIME ¼ SEC.
AC-FAIL REPORT DELAY 10 MIN.
EXIT DELAY
ENTRY DELAY 1
ENTRY DELAY 2
TELCO LINE-TEST DLY
AUTO ARM REARM DLY
SENSOR-WATCH TIME DISARMED HOURS
Note: If both programming locations are left blank, refer to the notes in the Time Selection table for feature timeout.
To select a time up to 15 seconds, 15 minutes, 15 hours, or 15 days, program the respective entry into the second box only; do
not program the first box. To select a time greater than 15 seconds, 15 minutes, 15 hours or 15 days, program both boxes as follows:
1. For the feature selected, choose an appropriate time in units shown (all seconds, minutes, hours, or days — not minutes and
seconds, etc.).
2. Divide the time chosen by 16. Enter the quotient in the 1st BOX and the remainder in the 2nd BOX.
3. Check entries by adding the contents of the 2nd BOX to 16 times the contents of the 1st BOX. (Remember that a "zero" entry
represents 10.)
Example. Program Entry Delay 1 for 1 minutes.
1. Entry Delay 1 is in units of seconds, thus delay time is 90 seconds.
2. Divide by 16: 90/16 = 5 (quotient) + 10 (remainder).
3. Enter the quotient in the 1st BOX and the remainder in the 2nd BOX
4. Check entries (remember, a "0" entry = 10): (16x5) + 10 = 90
TouchTone Dialing Only
TouchTone Dialing with Rotary Backup
Select TouchTone Dialing Only if the subscriber has TouchTone service. TouchTone dialing is faster than rotary dialing, but not
always as reliable.
For the communicator to use TouchTone on all dial attempts, program TouchTone Dialing Only. To use TouchTone on the first
attempt with subsequent Rotary dial, program TouchTone Dialing with Rotary Backup. TouchTone Dialing Only will override
TouchTone Dialing with Rotary Backup if both are selected. Note that if Backup Reporting is also selected, the communicator will
alternate between TouchTone and rotary dial to reach Telephone 1, then Telephone 2. See Backup Report on Telco 2.
Transmit "402" Closing Code
Program to send a "402" closing code (for Ademco Point ID modem format) in place of a "401" code.
L
NAPCO Security Systems
UNITS MAX. PROG. TIME
UNTIMED
MIN.
MIN. UNTIMED
SEC. 4 MIN, 15 SEC (255 SEC)
MIN. UNTIMED
MIN. UNTIMED
MIN. UNTIMED
4 MIN, 15 SEC (255 SEC)
SEC.
63.25 SEC (255 QTR-SEC)
42 HR, 30 MIN (2550 MIN)
SEC.
4 MIN, 15 SEC (255 SEC)
SEC.
4 MIN, 15 SEC (255 SEC)
SEC. 4 MIN, 15 SEC (255 SEC)
SEC. 4 MIN, 15 SEC (255 SEC)
MIN. 4 HR, 15 MIN (255 MIN)
255 HOURS
Time t: 0 1 2 3 4
Entry: * 1 2 3 4
(1)
NOTES: The output used for Burglary must be at least 4 minutes
in Residential UL installations, 15 minutes in Commercial UL
(2)
installations. If both locations are left blank, this feature will remain
(2)
active until the system is disarmed. When both locations are
programmed "F", maximum time will be 4 hours, 15 minutes (255
(2)
(3)
minutes). If both locations are left blank, this feature will not
activate (timeout = 0).
60 sec; Maximum Entry Delay = 45 sec.
are left blank, delay will default to 10 sec.
(1)(2)
hours (accumulated between armed periods).
(1)(2)
Time Selection
(2)
The following times are programmable:
Any timeout up to those shown in the foregoing table
(3)
may be programmed. Note that each of the above times is
programmed in two locations. The first location has an
(3)
assigned time factor of 16, the second a time factor of 1.
(4)
(4)
(4)
(5)
(6)
5 6 7 8 9 10 11 12 13 14
5 6 7 8 9 0 B C
*Blank.
X
(4)
In UL installations: Maximum Exit Delay =
(5)
If programming locations
(6)
Time in units of disarmed
1st BOX 2nd BOX
tx16 tx1
15
D E F
1st BOX
5
quotient remainder ("0" for 10)
GEM-P3200 Installation Instructions
!
Page 49
2nd BOX
0