NAPCO Gemini GEM-P816 Programming Instructions Manual

NAPCO Gemini GEM-P816 Programming Instructions Manual

Table of Contents

Advertisement

HARDWIRE
CONTROL PANEL/COMMUNICATOR
"Classic" GEM-RP1CAe2 Keypad and the "K Series" GEM-K1CA Keypad
G E M I N I
SYSTEM READY
01/01/00
A
1
B
4
C
7
C O M P U T E R I Z E D S E C U R I T Y S Y S T E M
"Classic" GEM-RP1CAe2
Quick Start (for "Classic" GEM-RP1CAe2)
1. Refer to the wiring diagram, connect Siren, Aux. Power,
PGM Output, Remote Bus, Earth ground, Zone and Tele-
phone wiring.
NOTE:
(WI994).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 34).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press
456789 A
Dealer Code
Press NO (
) until "ACTIVATE PROGRAM Y/N" appears on the
g
keypad display.
Press YES (
) to Enter Dealer Program Mode. Go to page 5.
F
© Napco 2004
R
G E M - P 8 1 6
Programming the GEM-P816 Control Panel with the
12:00 AM
NEXT/YES
D
2
3
E
PRIOR/NO
F
5
6
AREA
8
9 0
G
See Installation Instructions
PROGRAMMING
INSTRUCTIONS
G E M I N I
C O M P U T E R I Z E D S E C U R I T Y S Y S T E M
Quick Start (for "K-Series" GEM-K1CA)
1. Refer to the wiring diagram, connect Siren, Aux. Power,
PGM Output, Remote Bus, Earth ground, Zone and Tele-
phone wiring.
(WI994).
2. Connect AC power first and then the battery.
3. Configure the keypad (see page 34).
4. Access the Easy Menu Driven (Dealer Program) Mode:
Press
456789 R
Press NO (
Q
keypad display.
Press YES (
P
WIRELESS
SYSTEM READY
01/01/00
12:00 AM
U
R
1
2
3
B
4
5
6
C
7
8
9 0
"K Series" GEM-K1CA
NOTE:
See Installation Instructions
Dealer Code
) until "ACTIVATE PROGRAM Y/N" appears on the
) to Enter Dealer Program Mode. Go to page 5.
NEXT/YES
P
PRIOR/NO
Q
AREA
G
WI995C 3/04

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Gemini GEM-P816 and is the answer not in the manual?

Questions and answers

Summary of Contents for NAPCO Gemini GEM-P816

  • Page 1 ) until “ACTIVATE PROGRAM Y/N” appears on the keypad display. keypad display. Press YES ( ) to Enter Dealer Program Mode. Go to page 5. Press YES ( ) to Enter Dealer Program Mode. Go to page 5. © Napco 2004 WI995C 3/04...
  • Page 2: Important Note

    VERSION 10 OR LATER. IMPORTANT NOTE This manual supports the keypad programming of the GEM-P816 control panel with the NAPCO "classic" GEM- RP1CAe2 keypad as well as the GEM-K1CA "K Series" keypad. The new "K Series" GEM-K1CA model offers the new STAY and AWAY buttons with simplified functionality, along with the new MENU and ENTER buttons.
  • Page 3: Table Of Contents

    Programming Conventions Used in this Manual ..14 System Delays & Timeouts (Addr 0000-0002, 1059 & 1179) ................15 System Delays & Timeouts (Addr 0711, 0715-0717) .. 15 Refer to accompanying GEM-P816 Installation Instructions (WI994) for installation information. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 4: System Programming Options

    For direct high-speed data transfer to the control panel from a desktop computer, connect the download jack (JP2) on the panel to the LOCAL jack (J3) on the Napco PCI2000/3000 computer interface using the supplied 6- conductor cable. (Refer to PCI2000/3000 Installation Instructions WI443 for wiring diagram and procedures).
  • Page 5: Easy Menu Driven Program Mode

    Should it be necessary to create a new custom default pro- gram, (a) from the Dealer Program Mode, press the button to enter the Direct Address Program Mode; (b) access Location 1197 (Clear Program); (c) press the button and start over. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 6: Gem-Rp1Cae2/Gem-K1Ca Easy Program Menu

    Valid entries are from 01 to 32. Directly enter each zone number, including leading zeros. • Press to save and repeat for any additional zone(s); press the NEXT/YES button to proceed. (Direct Entry) NOTE: 24 Hour Zones will automatically be programmed as audible (Burg Output). NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 7: Chime Zones In Area 1

    Press YES to enable Telco Line Fault Test. Line Test? • Press NO to continue. NOTE: If enabled, a Telco Line Fault Test Delay of 60 sec. will auto- matically be programmed. (Press YES or NO) NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 8: Enable Burg Output Chirp On Keyfob

    “User Program”. Enter “2222” for a user code, blank(•) Access “• (blank) 9” for area 1 options and “• (blank) • blank(•) Ambush (blank)” for area 2 options. blank(•) Add 8 * User Program NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 9: Rf Transmitter Points

    NEXT/YES button to proceed when all key fobs have been entered. NOTE: When programming the ID Code number, “0” through ”9” = through ; A = ; B = ; D = ; E = and “F” = NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 10: Key Fob Transmitters As Zone Input Devices

    To proceed to the next description, place the cursor under the Zone Number (e.g. “01”) and change the Zone Number using . Program new description as above. • NOTE: Zone Descriptions can only be entered through the GEM-RP1CAe2 Keypad or by using the Napco Quickloader Software. See Easy Menu Programming Worksheet for available zone description characters. Enter Date (Press to set cursor).
  • Page 11: Direct Address Program Mode

    "Binary" format). DETERMINE THE DATA ENTRIES 1. Referring to ZONE FEATURES in the Programming Worksheets that follow, the Exit/Entry Follower for Zones 1 through 8 are located at address 0506. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 12: Decimal Format

    2. Answer NO to all questions until “ACTIVATE PROGRAM Y/N” is displayed; then press YES. NOTE: If you pass “ACTIVATE PROGRAM”, scroll backward using 3. Press to enter the Address Program Mode. Address "0000" will display. 4. Press to access Address 0715. The existing data will display and the cursor will 0715 NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 13: Hexadecimal Format

    (•) ¼sec. = 1 sec. blank (•) ¼sec. = 1.25 sec. blank (•) ¼sec. = 1.5 sec. blank (•) ¼sec. = 1.75 sec. 2 seconds blank (•) ¼sec. = 2 sec. ¼sec. = 63.25 NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 14: Programming Conventions Used In This Manual

    It is recom- mended that the panel be uploaded to NAPCO's PCD-Windows software following any keypad programming and that the PCD-Windows's error-check feature be utilized to reduce the possibility of programming omissions or conflicts.
  • Page 15: System Delays & Timeouts (Addr 0000-0002, 1059 & 1179)

    1. Enter delay/timeout in corresponding address locations above. Note: All entries for address 0716 are in quarter seconds (.25 seconds). Therefore, the default of 008 results in a 2 second timeout. 2. Press to save. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 16: System Output Timeouts (Addr 0710, 0712-0714)

    Pager report will now appear as “983 22 1234”. NOTE: See CS Receiver Options to select Pager Format. Leading Digits for Pager Format 1. Enter in 1st and 2nd Leading Digits as shown. (2nd Digit) 2. Valid entries are: 0-9. Press to save. [Default = blank (•) blank (•)] NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 17 (•), then the 2-digit Global Ambush Code is the two digits entered in address 1054. Ambush Code Enter in address location (both 1st and 2nd digits); valid entries are 1-9. 3. Press [Default = blank (•) blank (•)] save. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 18: System Options (Addr 0718-0722, 1060-1062)

    *** NOTE: If “Enable Global Ambush Code” in Address 0720 is selected, then program the 2-digit “Global Ambush Code” in Address 1054. If Address 1054 is left blank (•), then, the 2-digit “Global Ambush Code” will be “99”. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 19: Cs Receiver Opt. (Addr 0170-0235)

    2. Enter up to 20 digits from left to right. NOTE: Leave trailing boxes blank (•). Press [Enter] or [ON/OFF] to save. 3. Valid entries are: 1-9, B = button, C = button, D = 3 sec. pause, E = Wait for dial tone, F = ignore location NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 20: Cs Subscriber Reporting Opt. (Addr 0259-0350)

    [Default = blank (•) blank (•) from address 0319-0332] Exit Error 0348 * NOTE: Keypad Aux. is not to be selected for [Default = blank (•) blank (•) from address 0333-0350] Recent Close 0349 UL Installations. Fault Find 0350 NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 21 Disable Wait for Handshake * NOTE: If neither Touch-tone Dialing nor Disable Auto Dial Tone Detect Touch-tone w/Rotary Backup is selected, then system defaults automatically to Rotary Dialing. Leave blank (•) to select Rotary Dialing. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 22: Cs Zn Reporting Opt. (Addr 0358-0389 & 0391-0394) 21 Cs User Reporting Opt. (Addr 0440-0459)

    Select the desired option entering the option number (1-8) for each digit. At the keypad, enter corresponding option number in address location. NOTE: Dark shaded data value box shows option not available. Press to save. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 23: Ezm Group & Area Arming Opt. (Addr 0737-0744)

    [Default = blank (•)] Enter either blank() or "1" in corresponding address location. NOTE: Dark shaded data value box shows option not available. PRIORITY ARMING/AREA 1 DATA ENTRIES OPTION Press to save. blank (•) Not Used Enabled NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 24: Area Bell Control Options (Addr 0745-0749)

    For example, if you wish to grant an Area 1 keypad the ability to turn off an PGM2 output, enter "2" in Address 0749. Enter digit in address location. NOTE: Dark shaded data value box shows option not available. Press to save. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 25: Keypad Options (Addr 0723-0736)

    Select the desired option entering the option number (1-8) for each digit. At the keypad, enter corresponding option number in address location. NOTE: Dark shaded data value box shows option not available. Press to save. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 26: Zones 1-16 Options (Addr 0490-0595)

    Select the desired zone option by entering the option number (1-8) for each selected zone. Enter corresponding option number in address location. NOTE: Dark shaded data value box shows option not available. Press [Enter] or ON/OFF] to save NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 27 WI995C 2/04 Page 27 THIS PAGE INTENTIONALLY LEFT BLANK NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 28 Page 28 WI995C 2/04 THIS PAGE INTENTIONALLY LEFT BLANK NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 29 WI995C 2/04 Page 29 THIS PAGE INTENTIONALLY LEFT BLANK NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 30: Rf Rcvrs. & Sup. Timers (Addr 1038-1053 & 1180)

    Type E Smoke Detector 1052 Type F Napco Glass Break 1053 [Default = blank (•) from address 1046-1053]. Default = 8 (240 minutes) NOTE: These timers apply only to Supervised RF Transmitters (see RF Transmitters in Easy Menu Driven Mode Programming).
  • Page 31: Clear Program Features (Addr 1197 & 1198)

    K1CA and a new GEM-RP1CAe2 are automatically configured as Keypad #1. See Keypad Configuration Mode. Press the button to silence the sounder and exit the User Program Mode. If a GEM-RP2ASe2/GEM-K2AS keypad is used, configure address jumpers as Keypad #1 (See WI1182). NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 32: Accessing User Program Mode

    Enter the new User Code using the number buttons (0-9). If an old code is displayed, program over it. To erase the digit at the cursor, press button. Press the button to save the code in memory. Repeat this procedure for each user. To proceed to Zone-Description programming, press the NEXT button or the PRIOR but- ton. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 33: Zone Descriptions

    (Direct Entry) then press once again to save. NOTE: To enter the date and time, GEM-RP1CAe2/GEM-K1CA keypad (version 6 or greater) must be used and “Enable Keypad Time/Date Display” (Address 0718) must be enabled. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 34: Keypad Configuration Mode

    1. Enter the assigned keypad number 01–07, then press to save. A valid number will be acknowledged by a short beep; an invalid number will be re- jected by a long beep. 2. Press to continue or press to exit. NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 35 (the display will loop back through se- lections, for changes) or press the button to exit the Keypad Con- 01 OUT OF SYSTEM figuration Mode (display will read “ ”). Then replace Jumper JP1 across Pins 1–2 (top two). NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 36: Easy Menu Programming Worksheets

    B = SIA 3 = Silent Knight Fast C = Ademco Point ID 4 = Radionics, DCI, Franklin Slow E = Pager User Codes: USER CODE AREA 1 AREA 2 (up to 6 digits) OPTIONS OPTIONS NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 37 EASY MENU PROGRAMMING WORKSHEET - 2 OF 3 RF Transmitter Points: XMTR ZONE RF ID CHECK POINT (printed on xmtr box) Key Fob Transmitters: KEY FOB # Area RF ID CHECK OPTION OPTION (printed on xmtr box) NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 38 A B C D E F G H I J K L M N O P Q R S T U V W X Y Dealer Code: NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 39: Alphabetical Index

    Direct Address 0718 DOWNLOAD/CALLBACK OPTIONS Direct Addresses 1183 & 0236-0255 Enable Alarm Output on Telco Fail only when Armed Direct Address 0721 Enable AutoArm if not closed at end of Window Direct Address 0718 NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 40 PRIORITY AREA ARMING OPTIONS Direct Addresses 0743 & 0744 Direct Address Priority with Bypass (Enable Zone) 0492, 0547 Pulse Event Codes (CS ZONE REPORTING) Direct Addresses 0358-0389 Direct Address Pulsed Alarm Output (Enable Zone) 0501, 0556 NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 41 0536, 0591 Zone ANDing Group 4 (Enable Zone) Direct Address 0537, 0592 Zone Area 1 (Enable Zone) Direct Address 0526, 0581 Zone Descriptors Easy Menu Driven Zones Report Code (Zones 1-16) Direct Address 0358-0389 NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 42: Address Number Index

    0430-0449 User Opening/Closing Telco 1 & 3 0440-0459 CS USER REPORTING OPTIONS 0460-0469 SYSTEM RESPONSE ACTIVATED BY GLOBAL EVENT/TROUBLE 0470-0477 SYSTEM RESPONSE ACTIVATED BY AREA 1 EVENT/TROUBLE 0490 50ms Loop Response (A) (Enable Zone) NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 43 0558 PGM2 Output (Enable Zone) 0559 Entry/Exit 1 (Enable Zone) 0560 Entry/Exit 2 (Enable Zone) 0561 Exit/Entry Follower (Enable Zone) 0562 Auto Reset (Enable Zone) 0563 Swinger Shutdown (Enable Zone) 0564 Chime (Enable Zone) NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 44 Disable Keypad Instant Mode 0719 Enable Manager's Mode 0719 Enable Local Alarm on First Zone AND Trip 0719 Maintained Keyswitch Arming 0719 Suppress Bypass Reminder when Armed 0720 Change Pulse Output to Temporal Output NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 45 Report Exit Error/Recent Close 1062 Sound Alarm On Exit Error 1179 Report Cancel Window 1180 RF RECEIVER & SUPERVISORY TIMER OPTIONS 1183 DOWNLOAD/CALLBACK OPTIONS 1183 Number of Rings before Pickup 1197 Clear Dealer Program 1198 Cold Start NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 46 Page 46 WI995C 2/04 NOTES NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 47 WI995C 2/04 Page 47 NOTES NAPCO Security Systems GEM-P816 Programming Instructions...
  • Page 48: Gem-P816 Wiring Diagram

    Page 48 WI995C 2/04 GEM-P816 WIRING DIAGRAM NAPCO Security Systems GEM-P816 Programming Instructions...

Table of Contents