Error Code List - JUKI AMB-289/IP-420 Instruction Manual

5. ERROR CODE LIST

Pictograph
Error code
E0
E0
E00
E099
E0
E9
E9
E9
E9
E9
E99
E9
E9
E99
* For errors other than these errors, refer to the Instruction Manual.
Description of error
Detection of step-out of presser lifting motor error
This error occurs when step-out of presser lifting motor is
detected. Check whether the mechanical load is heavy.
Air pressure drop
Check whether the air pressure dropped.
Stop switch
This error occurs when stop switch is pressed.
Button loader motor step-out detection error
This error occurs when step-out of button loader motor is
detected.
Confirmation of tilt of machine head
Check whether tilt of machine head sensor is OFF.
Feed plate lowering sensor undone error
This error occurs when feed plate lowering sensor fails to
work during sewing machine operation. Check whether a
button or the like is put under the feed plate.
Feed plate lifting sensor undone error
This error occurs when feed plate lifting sensor fails to
work during sewing machine operation.
Tongue close/open sensor undone error
This error occurs when sensor is not ON or OFF at the
time of tongue close/open operation.
Chuck close/open sensor undone error
This error occurs when a button is not in the chuck at the
time of sewing machine operation.
Chuck level sensor undone error
This error occurs when sensor fails to work at the time of
chuck level operation. Perform confirmation of the sensor
position.
Chuck inversion sensor undone error
This error occurs when sensor fails to work at the time of chuck
inversion operation. Perform confirmation of the sensor position.
Tongue type error
This error occurs when "AMB9" type tongue and
"AMB9" type one are mixedly used in the cycle data.
Change the cycle data.
Button holding height over at the time of sewing
This error occurs when button holding height (.0 mm)
is over and sewing cannot be performed at the time of
button sewing. Change the sewing data.
Y feed motor move limit value over
This error occurs when input data of the button height of
shank/marble sewing exceeded the maximum ( mm) of
Y feed move amount. Change the sewing data.
– 0 –
How to recover Place of recovery
P o s s i b l e t o D a t a i n p u t
r e c o v e r b y screen
reset.
P o s s i b l e t o D a t a i n p u t
r e c o v e r b y screen
reset.
P o s s i b l e t o D a t a i n p u t
r e c o v e r b y screen
reset.
P o s s i b l e t o D a t a i n p u t
r e c o v e r b y screen
reset.
P o s s i b l e t o D a t a i n p u t
r e c o v e r b y screen
reset.
D a t a i n p u t
P o s s i b l e t o
screen
r e c o v e r b y
reset.
P o s s i b l e t o
D a t a i n p u t
r e c o v e r b y
screen
reset.
P o s s i b l e t o
D a t a i n p u t
r e c o v e r b y
screen
reset.
P o s s i b l e t o
D a t a i n p u t
r e c o v e r b y
screen
reset.
P o s s i b l e t o
D a t a i n p u t
r e c o v e r b y
screen
reset.
D a t a i n p u t
P o s s i b l e t o
screen
r e c o v e r b y
reset.
D a t a i n p u t
P o s s i b l e t o
screen
r e c o v e r b y
reset.
D a t a i n p u t
P o s s i b l e t o
screen
r e c o v e r b y
reset.
D a t a i n p u t
P o s s i b l e t o
screen
r e c o v e r b y
reset.