JUKI AMB-289/IP-420 Instruction Manual page 8

No.
Compensation of lower left position of upper button
This item is set when cloth is pulled and the amount of blindstitch
on the left side is different from that on the right side.
Compensation of 3rd stitch at the start of sewing
This item compensates the position of rd stitch at the start of sewing
to prevent thread from slipping off at the start of button sewing
Blindstitch width
This item has to be set within the range where needle and tongue
do not come in contact with each other.
Blindstitch amount
This item sets the blindstitch amount to cloth.
Buttonhole height of shank/marble button sewing
(Height from the feed plate)
This item is set to prevent the contact of needle and buttonhole.
Thinning level of the stay button
This item decreases the number of cross-over stitches of the lower side
button at the time of stay button sewing.
Lateral compensation of needle entry of lower button at the
time of sewing counter button (front : 4 holes, rear : 2 holes)
Perform compensation to such an extent that needle does not come
in contact with buttonhole within the range of lower buttonhole.
Number of stitches of tie stitch at the end of sewing flat button
directly to cloth.
This item sets the number of stitches of tie stitch at the end of
sewing flat button directly to cloth.
Number of stitches of tie stitch at the end of counter sewing
This item sets the number of stitches of tie stitch at the end of
counter sewing.
Button sewing height (only neck wrapping of sewing flat/
wrapped-around button with blindstitch)
This item sets the button holding height (finished height)
in the neck wrapping process.
Button height (shank/marble)
This item sets the button holding height (finished height)
in the neck wrapping process.
Button height (counter button)
This item sets the button holding height (finished height)
in the button sewing process.
Number of stitches at the start of sewing of neck wrapping
This item sets the number of stitches at the start of sewing of
neck wrapping.
Number of stitches of tie stitch at the end of sewing of neck
wrapping
This item sets the number of stitches of tie stitch
at the end of sewing in the neck wrapping process.
Compensation of the button holding height at the time
of sewing flat/wrapped-around button with blindstitch
This item sets when compensating the button holding height in the
button sewing process and desiring to give slackness between
button and neck wrapping section.
Thread release compensation
This item is the compensation value of the button holding height
in the button sewing process. Sewing is performed in the neck
wrapping process by gradually returning the compensation value to
the former one. This item is set when desiring to tightly wrap up
to the root of the button.
*  The maximum value of the range of data editing depends on the setting of
*  The maximum value of the data edit range varies according to the sewing shape.
Item
: Without thinning
: Thinning level 
–  –
Setting range
–.00 to
.00
0 to 0.
0.0 to .
–.00 to
.00
0.0 to 0.0
– – –
: Thinning level 
: Thinning level 
0 to 0.0
 to 
 to 
0. to .0
0 to .0
0 to 0.0
 to 
 to 
–.0 to .0
–.0 to .0
Edit unit Initial display Remarks
0.0mm 0
0.0mm 0
0.mm 0.
0.0mm 0.0
0.mm .0
– – –
Without
thinning
0.0mm 0.0
 stitch 
 stitch 
0.mm .
Shank
0.mm
button: .
Marble
button: .
.
0.mm

 stitch

 stitch
–0.
0.mm
0.
0.mm
.
*
*