Yamaha YZ450F(Y Owner's Manual Page 177

Hide thumbs

Advertisement

HANDLING NOTE
Do not loosen the screw (throttle
position sensor) "1" except when
changing the throttle position sen-
sor due to failure because it will
cause a drop in engine perfor-
mance.
CHECKING THE COUPLERS AND
LEADS CONNECTION
1. Check:
• Couplers and leads connection
Rust/dust/looseness/short-circuit
→ Repair or replace.
CHECKING THE THROTTLE
POSITION SENSOR COIL
1. Inspect:
• Throttle position sensor coil resis-
tance
Out of specification → Replace.
Tester (+) lead → Blue lead "1"
Tester (-) lead → Black lead "2"
Throttle po-
Tester se-
sition sen-
lector posi-
sor coil
resistance
4–6 kΩ at
20°C (68 °F)
2. Loosen:
• Throttle stop screw "1"
Turn out the throttle stop screw until
the throttle shaft is in the full close po-
sition.
THROTTLE POSITION SENSOR SYSTEM
3. Inspect:
• Throttle position sensor coil vari-
able resistance
Check that the resistance in in-
creased as the throttle grip is
moved from the full close position
to the full open position.
Out of specification → Replace.
Tester (+) lead → Yellow lead "1"
Tester (-) lead → Black lead "2"
Throttle position
Zero –2
CHANGING AND ADJUSTING THE
THROTTLE POSITION SENSOR
1. Remove:
• Throttle position sensor coupler
• Carburetor
2. Remove:
tion
• Screw (throttle position sensor)
"1"
kΩ×1
• Throttle position sensor "2"
Loosen the screw (throttle position
sensor) using the T25 bit.
3. Replace:
• Throttle position sensor
4. Install:
• Throttle position sensor "1"
• Screw (throttle position sensor)
"2"
• Align the slot "a" in the throttle posi-
tion sensor with the projection "b"
on the carburetor.
• Temporarily tighten the screw
(throttle position sensor).
Tester
selec-
sensor coil vari-
tor po-
able resistance
sition
Full
Full
closed
opened
4–6
kΩ×1
kΩat
kΩat
20°C
20 °C
(68 °F)
(68 °F)
6-7
5. Install:
• Carburetor
• Throttle position sensor coupler
6. Adjust:
• Engine idling speed
Refer to "ADJUSTING THE EN-
GINE IDLING SPEED" section in
the CHAPTER 3.
7. Insert the thin electric conductors
"2" (lead) into the throttle position
sensor coupler "1", as shown, and
connect the tester to them.
Tester (+) lead → Yellow lead "3"
Tester (-) lead → Black lead "4"
• Do not insert the electric conduc-
tors more than required because
it may reduce the waterproof
function of the coupler.
• Make sure that a short-circuit
does not develop between the
terminals because it may cause
damage to electrical compo-
nents.
8. Start the engine.
9. Adjust:
• Throttle position sensor output
voltage
Adjustment steps:
a. Adjust the installation angle of the
throttle position sensor "1" to ob-
tain the specified output voltage.
Measure the output voltage accurate-
ly with a digital electronic voltmeter
that gives an easy reading of a small
voltage.

Advertisement

Comments to this Manuals

Symbols: 0
Latest comments:
  • nick Jan 26, 2016 10:47:
    The download is jacked up, so it's only really viewable on the site, but can't really complain since it's free.