Util5 Hi-Hat Setup; Util4-2 Foot Switch Input Page; Util4-3 Pad 10-12 Switch Page; Util5-1 Close Position Page - Yamaha DTX-MULTI Owner's Manual

Foot Switch Input page
UTIL4-2
UTIL4-2≥≥≥≥<PAD>
FootSwInSel=ftSw
1 Foot switch input selection (FootSwInsel)
Use this parameter to specify whether a foot switch ("ftSw"),
a hi-hat controller ("HH65"), or a foot controller ("FC7") is
connected via the FOOT SW jack.
Settings ftSw, HH65, or FC7
NOTE
• The velocities sent when a hi-hat controller or a foot controller is con-
nected will depend on the setting made on the Trigger Velocity page
(MIDI1-7).
• The velocities sent when a foot switch is connected also depend on
the setting made on the Trigger Velocity page (MIDI1-7); however, if
"variable" is selected on that page, velocities will be sent with a fixed
value of 100.
Pad 10-12 Switch page
UTIL4-3
UTIL4-3≥≥≥≥<PAD>
Pad10-12=enable
1 Pad10-12
Use this parameter to turn rim pads 10 to 12 on ("enable") or
off ("disable"). This function can prove useful in preventing
voices assigned to these rim pads from being played when
they are accidentally struck instead of pads 7 to 9.
• enable ................. The rim pads will operate in the normal
way.
• disable ................ Functions assigned to these rim pads will
be disabled. When they are struck, the
DTX-MULTI 12 behaves in the same way
as if the corresponding main pads (7 to 9)
had been struck.
Settings enable or disable
UTIL5 HI-HAT
Hi-hat Setup
UTIL5
≥≥≥≥≥HI-HAT
In the HI-HAT section, you can set parameters related to hi-hats.
With the HI-HAT page (UTIL5) displayed, press the [ENTER]
button to access its three parameter-setting pages (UTIL5-1 to
UTIL5-3). You can use the [B]/[C] buttons to navigate between
these pages.
UTIL5-1
1
1 Close position (ClosePosi)
Use this parameter to adjust the position at which the hi-hat
switches from open to closed when a hi-hat controller is
depressed. The lower the value, the smaller the virtual open-
ing between the top and bottom hi-hats.
Settings
UTIL5-2
1 Splash sensitivity (SplashSens)
Use this parameter to set the degree of sensitivity for detect-
ing hi-hat foot splashes. The higher the value, the easier it will
be to produce foot-splash sounds with the hi-hat controller.
1
High values may, however, result in splash sounds being unin-
tentionally produced when, for example, you depress the hi-
hat controller lightly to keep time. It is a good idea to set this
parameter to "off" if you do not want to play foot splashes.
Settings
UTIL5-3
1 Send hi-hat controller (SendHH)
Use this parameter to enable ("on") or disable ("off") the
sending of MIDI messages corresponding to continuous
motion of the hi-hat controller between the open and closed
positions.
Settings
NOTE
• If "hi-hat" is selected on the Hi-Hat Function page (KIT7-3), MIDI mes-
sages will be sent only when this parameter is set to "on".
• If "MIDI" is selected on the Hi-Hat Function page (KIT7-3), MIDI mes-
sages will always be sent, regardless of whether this parameter is set
to "on" or "off".
UTILITY Setting Area (UTIL)
Close Position page
UTIL5-1≥<HI-HAT>
≥ClosePosi=+10
-32 to +0 to +32
Splash Sensitivity page
UTIL5-2≥<HI-HAT>
≥SplashSens=127
off or 1 to 127
Send Hi-hat Controller page
UTIL5-3≥<HI-HAT>
≥≥≥SendHH=on
off or on
1
1
1
89
Owner's Manual