Midi1-8 Trigger Polyphony Page; Midi1-9 Trigger Alternate Group Page; Midi1-1 Control Change Number & Value Page; Midi1-2 Midi Channel Page - Yamaha DTX-MULTI Owner's Manual

Trigger Polyphony page
MIDI1-8
MIDI1-8≥-º¡-
TrgMonoPoly=poly
1 Pad number
01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW,
Settings
HHCL, or HHSP
B Trigger mono/poly (TrgMonoPoly)
Use this parameter to control what happens when the pad
indicated by 1 is struck repeatedly.
• mono ........ The previous sound will be stopped before a
new sound starts.
• poly .......... Previous sounds will continue to play when a
new sound starts.
Settings mono or poly
NOTE
• If no note numbers have been assigned to any of the pad's layers (A to
D) on the MIDI Note page (MIDI1-2), this setting will be displayed as "-
--" and modification will not be possible.
• MIDI Note Off messages are not sent when "off" has been selected on
the Receive Key-Off page (MIDI1-5). If you want to set trigger monoph-
ony, therefore, be sure to set this parameter to "on". This will ensure
that Note Off messages are sent to prevent overlapping voices.
Trigger Alternate Group page
MIDI1-9
MIDI1-9≥-º¡-≥≥
TrgAltGrp=off
1 Pad number
01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW,
Settings
HHCL, or HHSP
B Trigger alternate group (TrgAltGrp)
Use this parameter to assign the pad indicated by 1 to an
alternate group if so required. Alternate groups are monopho-
nic sets of pads, and therefore, only one pad from an alternate
group can be producing a sound at any time. If a pad is struck
while another pad from the same alternate group is already
producing a sound, a MIDI Note Off message will be sent for
the first pad together with the MIDI Note On message for the
second. In order to use trigger alternate groups with voices
played on MIDI channel 10, the sending of MIDI Note Off
messages must be enabled by selecting "on" for RcvKeyOff
on the Receive Key-Off page (MIDI1-5). Up to 32 trigger
alternate groups can be setup on your DTX-MULTI 12. If
there is no need for a pad to be assigned to a trigger alternate
group, you can set this parameter to "off".
Settings off or 1 to 32
NOTE
• If no note numbers have been assigned to any of the pad's layers (A to
D) on the MIDI Note page (MIDI1-2), this setting will be displayed as "-
--" and modification will not be possible.
• MIDI Note Off messages are not sent when "off" has been set on the
Receive Key-Off page (MIDI1-5). If you want to use trigger alternate
groups, therefore, be sure to set this parameter to "on". This will ensure
that Note Off messages are sent to prevent overlapping voices.
Parameter-Setting Pages for
"CC" Messages
1
MIDI1-1
2
1 Pad number
Settings
B Control change number (CCNo)
Use this parameter to set the type of MIDI Control Change
message to be sent whenever the pad indicated by 1 is
struck.
Settings
C Control change value (Val)
Use this parameter to set a value for the MIDI Control Change
message to be sent whenever the pad indicated by 1 is
struck.
• VARI .........The control change value will depend on how
• 0 – 127 ......Control change messages are sent with this fixed
1
Settings
2
NOTE
• Before setting Val 3 to "VARI", it will be necessary to access the Trig-
ger Velocity page (MIDI1-7) with Message Type=note (MIDI1) and to
set the TrgVel parameter to "variable".
MIDI1-2
1 Pad number
Settings
B MIDI channel (MIDI Ch)
Use this parameter to set a MIDI channel for the Control
Change messages to be sent whenever the pad indicated by 1
is struck.
Settings
Control Change Number &
Value page
MIDI1-1≥-º¡-
CCNo=≥7/Val=VARI
2 3
01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW,
HHCL, or HHSP
1 to 95
hard the pad is struck.
value, regardless of how hard or soft the pad is
struck.
VARI or 0 to 127
MIDI Channel page
MIDI1-2≥-º¡-
≥≥≥MIDI≥Ch=10
01 to 12, 13, 13R1, 13R2, 14 to 17, FTSW,
HHCL, or HHSP
1 to 16
MIDI Setting Area (MIDI)
1
1
2
65
Owner's Manual