Yamaha DTX-MULTI Owner's Manual page 103

Individual Crosstalk Level page
TRG2-2-2
TRG2-2-2≥-¡¢-≥˛¸
Level=≥25%(¡£)
3
1 Pad
Use this parameter to select the pad(s) for which a crosstalk
level is to be set. You can also strike a pad to select it.
Settings UP, MID, LOW, or 01 to 17
NOTE
• Selection by striking is limited to pad groups (i.e., UP, MID, or LOW)
and the external pads (i.e., 13 to 17).
B Crosstalk source
Use this parameter to specify a pad or group of pads causing
crosstalk in the pad(s) indicated by 1. You can also strike a
pad to select it.
Settings UP, MID, LOW, or 01 to 17
C Crosstalk level
Use this parameter to specify a level for preventing crosstalk
from the pad(s) indicated by 2. If the input level produced at
the pad indicated by 1 is lower than this level whenever the
pad indicated by 2 is struck, it will be treated as crosstalk
and no trigger signal will be generated. Although higher set-
ting values are more effective in preventing crosstalk, they
can also make it difficult to play multiple pads at the same
time.
Settings 0% to 99%
Typical Examples of Crosstalk-
Prevention Setup – No. 1
● Use this approach when pad sensitivity is set
to allow playing by hand and striking of one of
the pads from the MID group (i.e., 4 to 9)
causes another pad from that group to pro-
duce a sound.
1 Navigate to the Individual Crosstalk Level page
(TRG2-2-2) and set its parameters as follows.
1: MID (i.e., pads 4 to 9), 2: MID (i.e., pads 4 to 9)
2 Hold down the [SHIFT] button and press the [UP/
DOWN] button to activate the input lock. (
will change to [MID]
NOTE
• The input lock must be activated here to prevent the selection
from changing when one of the other pads from the MID group
(i.e., 4 to 9) is struck in the next step.
1
2
-MID-
.)
3 While striking one of the pads from the MID
group (i.e., 4 to 9), raise the level indicated by 3
until other pads from that group no longer pro-
duce any sound.
TRG2-2-2≥[MID]˛¸
Level=≥28%(MID)
2
Press the [STORE] button to open the Trigger
4
Store page, and then store your trigger setup as
described on page 45.
Typical Examples of Crosstalk-
Prevention Setup – No. 2
● Use this approach when pad sensitivity is set
to allow playing by hand and, for example,
striking of Pad 4 also results in Pad 5 produc-
ing a sound
1 Navigate to the Individual Crosstalk Level page
(TRG2-2-2) and set its parameters as follows.
1: 05 (i.e., Pad 5), 2: 04 (i.e., Pad 4)
2 Hold down the [SHIFT] button and press the [UP/
DOWN] button to activate the input lock. (
will change to .)
[º∞]
NOTE
• The input lock must be activated here to prevent the selection
changing from Pad 5 to Pad 4 when Pad 4 is struck in the next
step.
While striking Pad 4, raise the level indicated by
3
3 until Pad 5 no longer causes a voice to play
(i.e., no longer produces a trigger signal).
NOTE
• If this level is set too high, Pad 5 may not produce any sound
when struck relatively softly together with Pad 4.
TRG2-2-2≥[º∞]≥˛¸
Level=≥28%(04)
3
Press the [STORE] button to open the Trigger
4
Store page, and then store your trigger setup as
described on page 45.
TRIGGER Setting Area (TRG)
1
3
-º∞-
1
2
Owner's Manual
103