Yamaha DTX-MULTI Owner's Manual page 40

Internal Design
Parameter
name
This parameter is used to set the delay volume for the
DlyLvlC
center channel.
This parameter is used to set the mixing level for the
DlyMix
delayed sound.
This parameter is used to set the modulation delay
DlyOfst
time's offset value.
This parameter is used to set the degree to which the
Drive
effect is applied.
This parameter is used to set the depth of modulation
DriveHorn
produced through rotation of the high-frequency horn.
This parameter is used to set the depth of modulation
DriveRotor
produced through rotation of the low-frequency rotor.
This parameter is used to set the degree by which the
DstL.Gain low frequencies from the distorted sound are boosted or
cut.
This parameter is used to set the degree by which the
DstM.Gain mid frequencies from the distorted sound are boosted or
cut.
This parameter is used to specify a curve that deter-
Edge
mines how the sound is distorted.
This parameter is used to set the cutoff frequency for the
EQ1Freq
EQ1 band (i.e., low shelving).
This parameter is used to set the gain for the EQ1 band
EQ1Gain
(i.e., low shelving).
This parameter is used to set the center frequency for
EQ2Freq
the EQ2 band.
EQ2Gain This parameter is used to set the gain for the EQ2 band.
This parameter is used to set the resonance of the EQ2
EQ2Q
band.
This parameter is used to set the center frequency for
EQ3Freq
the EQ3 band.
EQ3Gain This parameter is used to set the gain for the EQ3 band.
This parameter is used to set the resonance of the EQ3
EQ3Q
band.
This parameter is used to set the center frequency for
EQ4Freq
the EQ4 band.
EQ4Gain This parameter is used to set the gain for the EQ4 band.
This parameter is used to set the resonance of the EQ4
EQ4Q
band.
This parameter is used to set the cutoff frequency for the
EQ5Freq
EQ5 band (i.e., high shelving).
This parameter is used to set the gain for the EQ5 band
EQ5Gain
(i.e., high shelving).
This parameter is used to set the relative volumes of
ER/Rev
early reflections and reverberation.
This parameter is used to set the front-to-rear pan depth
F/RDpth (and is valid only when PanDirectn is set to "Lturn" or
"Rturn").
This parameter is used to set how the feedback sound
FBHiDmp decays in the high-frequency band (with smaller values
corresponding to faster decay).
[Chorus effects, Delay effects, and TempoFlanger]
This parameter is used to set how much of the delay
sound is fed back into the effect's input (with negative
values indicating that its phase is to be inverted).
[TempoPhaser]
FBLevel This parameter is used to set how much of the phaser's
output is fed back into its input (with negative values indi-
cating that its phase is to be inverted).
[Reverb effects]
This parameter is used to set the initial delay's feedback
level.
This parameter is used to set the feedback level for the
FBLvl1
first delay sound.
This parameter is used to set the feedback level for the
FBLvl2
second delay sound.
FBTime This parameter is used to set the feedback delay time.
This parameter is used to set the delay time for feedback
FBTime1
delay 1.
This parameter is used to set the delay time for feedback
FBTime2
delay 2.
40
Owner's Manual
Descriptions
Parameter
name
This parameter is used to set the delay time for the left
FBTimeL
feedback delay.
This parameter is used to set the delay time for the right
FBTimeR
feedback delay.
This parameter is used to set how much of the effect's
Feedback
output is fed back into its input.
This parameter is used to adjust the first fine-pitch set-
Fine1
ting.
This parameter is used to adjust the second fine-pitch
Fine2
setting.
This parameter is used to set the center frequency of the
H.Freq
high-frequency EQ band.
This parameter is used to set the amount by which the
H.Gain
high-frequency EQ band is boosted or cut.
This parameter is used to set the height of the simulated
Height
room.
This parameter is used to set the amount of time that
HiAtk elapses before compression is fully applied in the high-
frequency band.
This parameter is used to set the output level of the high-
HiGain
frequency band.
HiLvl This parameter is used to set the high-frequency level.
This parameter is used to activate and deactivate high-
HiMute
frequency muting.
[MltBndComp]
This parameter is used to set the compression ratio for
the high-frequency band.
HiRat
[Reverb effects]
This parameter is used to adjust the high-frequency
component.
This parameter is used to set the input-signal level at
HiTh which the compressor starts to process the sound in the
high-frequency band.
This parameter is used to set the speed of rotation of the
HornF
high-frequency horn at the "fast" setting.
This parameter is used to set the speed of rotation of the
HornS
high-frequency horn at the "slow" setting.
This parameter is used to set the high-pass filter's cutoff
HPF
frequency.
This parameter is used to set the amount of time that
InitDly
elapses before early reflections are produced.
This parameter is used to set the delay time for the first
InitDly1
delay.
This parameter is used to set the delay time for the sec-
InitDly2
ond delay.
This parameter is used to set the delay time for the left-
InitDlyL
channel delay.
This parameter is used to set the delay time for the right-
InitDlyR
channel delay.
This parameter is used to switch between mono and ste-
InpMode
reo input.
InpSelect This parameter is used to select an input.
This parameter is used to set the center frequency of the
L.Freq
low-frequency EQ band.
This parameter is used to set the amount by which the
L.Gain
low-frequency EQ band is boosted or cut.
This parameter is used to set the difference between left
L/RDiffuse and right delay times in order to produce a more spa-
cious sound.
This parameter is used to set the depth of the left-right
L/RDpth
panning effect.
This parameter is used to set a time lag for delay times
Lag
specified in terms of note lengths.
[SPX Flanger, TempoFlanger, SPX Chorus, and Sym-
phonic]
This parameter is used to set the depth of modulation.
LFODpth
[Tempo Phaser]
This parameter is used to set the depth of phase modu-
lation.
This parameter is used to set the left-right phase differ-
LFODiff
ence between modulation waveforms.
Descriptions