Table of Contents
Advertisement
CHAPTER 3 Installing Media Flow Controller with a CD or USB
Enter 3 to Halt without installing or restoring.
Enter 1, 2, or 3 :
3. Enter 1. The EULA is displayed; press the Space bar to page through it. You can enter q
to go to the end of the EULA.
Enter 1 to Read the EULA agreement again.
Enter 'accept' to accept the EULA agreement and continue with
installation.
Enter 2 to Reboot without installing or restoring.
Enter 3 to Halt without installing or restoring.
Enter 1, 2, 3, or 'accept' :
4. Enter accept. The following menu is displayed:
Enter 1 to Install Media Flow Controller.
Enter 2 to Restore Media Flow Controller.
Enter 3 to Reboot without installing or restoring.
Enter 4 to Halt without installing or restoring.
Note:
Install will delete all cached data.
Restore attempts to keep cached data.
Enter 1, 2, 3 or 4 :
5. If this is a first time installation, enter 1.
If this is NOT a first time installation, and you want to erase all the cached data, enter 1.
If this is NOT a first time installation, and you want to preserve cached data, enter 2. In
some situations some or all of the cached data still might not be preserved.
The installation proceeds; it can take 10 minutes or longer depending on how many disks
Media Flow Controller needs to format. When completed, the following menu is displayed:
Installation is done at <number>
>>> Phase 1 Installation Done <<<
Enter 1 to Reboot to complete the installation.
Enter 2 to Halt. Installation will continue when rebooted.
Enter 3 to Flash ethernet port LEDs.
Enter 4 to Configure ethernet names interactively.
Enter 5 to Specify device for eth0 and eth1.
Enter 6 to Reset ethernet naming back to default.
Most systems need the interface names assigned manually; the Ethernet naming default
is based on the device's PCI bus address order and often are not optimally assigned. It is
very important that eth0 be assigned to the proper port. Use options 4 or 5 to configure the
interface naming. See
6. After you have assigned the interface names, at the menu prompt, press 1 to reboot and
finish the installation.
The installation completes and an "unconfigured" prompt is displayed:
mfc-unconfigured-8a4990 login:
Finish with
32
Installing Media Flow Controller Software—CD or USB
"Ethernet Naming Options" on page
"Setting Up Basic System Connectivity."
Media Flow Controller and Media Flow Manager
25, for details.
Copyright © 2010, Juniper Networks, Inc.
Advertisement
Table of Contents
Related Manuals for Juniper MEDIA FLOW CONTROLLER 2.0.4
Related Products for Juniper MEDIA FLOW CONTROLLER 2.0.4
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
- Juniper MEDIA FLOW CONTROLLER 2.0.5
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
Need help?
Do you have a question about the MEDIA FLOW CONTROLLER 2.0.4 and is the answer not in the manual?