Table of Contents
Advertisement
Media Flow Controller and Media Flow Manager Installation GuideCHAPTER 3 Installing Media Flow Controller with a
Specify Devices to Use For eth0 and eth1, Ethernet Naming Option 5
If you are satisfied with the interfaces being automatically assigned and only need to set up
eth0 and perhaps eth1, and do not want to use the interactive method (option 4), you can use
option 5. Option 5 provides a way to specify which devices to use for eth0 and optionally eth1.
This example shows the assigning of the interfaces.
The eth-setup options, or "forms": default, least-ports, most-ports, pxe, <URL>, url,
Note!
HW address; are described in this section.
Example (input shown in bold):
Enter 1, 2, 3, 4, 5 or 6 : 5
==============================================================
Current ethernet device naming:
eth0
PCI address: 0000:01:00.0
Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06)
eth1
PCI address: 0000:01:00.1
Intel Corporation 82571EB Gigabit Ethernet Controller (rev 06)
eth10
PCI address: 0000:04:00.0
inet addr: 172.12.172.238
Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
eth11
PCI address: 0000:05:00.0
Broadcom Corporation NetXtreme BCM5721 Gigabit Ethernet PCI Express (rev 11)
==============================================================
Enter 0 to not make any ethernet device naming changes. Otherwise enter the
specification for eth0, and optionally eth1, and then press return to
generate the new port to name mapping. For an explanation of the
specifications that can be used enter 'help'.
Enter 0, help or the spec >
Enter 0, help or the spec > help
Syntax forms:
default|least-ports|most-ports|pxe|<URL>|url
<HWaddr> [<HWaddr>]
Examples of all the forms:
default
least-ports
most-ports
pxe
http://66.224.165.46/mfd-images/1.0.0-45.img
url
00:30:48:B8:F8:22
F8:22
f8:23-ca:A8
When "default" is specified, eth0 and eth1 are assigned in the order that the
devices are on the PCI bus. eth0 might not be assigned to the port that you
want it to be. The other options allow you to specify which port to use as
eth0 (and eth1).
HW address: 00:15:17:8A:49:90
HW address: 00:15:17:8A:49:91
HW address: 00:13:72:3C:33:56
HW address: 00:13:72:3C:33:57
Ethernet Naming Options
29
Advertisement
Table of Contents
Related Manuals for Juniper MEDIA FLOW CONTROLLER 2.0.4
Related Products for Juniper MEDIA FLOW CONTROLLER 2.0.4
- Juniper MEDIA FLOW MANAGER 2.0.2 - ADMINISTRATOR S GUIDE AND CLI
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - CONFIGURING INTRUSION DETECTION AND PREVENTION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - M-SERIES AND MX-SERIES DEVICES GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.2 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.3 - ADMINISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - CONFIGURING J SERIES SERVICES ROUTERS AND SRX SERIES SERVICES GATEWAYS GUIDE REV
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - ADMININISTRATION GUIDE REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - REV1
- Juniper NETWORK AND SECURITY MANAGER 2010.4 - M-SERIES AND MX-SERIES DEVICES GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - CATEGORY OFFENSE INVESTIGATION GUIDE REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - EVENT CATEGORY CORRELATION REV 1
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 R2 - LOG MANAGEMENT ADMINISTRATION GUIDE REV 1
- Juniper STRM LOG MANAGEMENT 2008.2 - S 6-2008
- Juniper MEDIA FLOW CONTROLLER 2.0.5
- Juniper NETWORK AND SECURITY MANAGER 2010.2
- Juniper SECURITY THREAT RESPONSE MANAGER 2008.2 - AQL EVENT AND FLOW QUERY CLI GUIDE
Need help?
Do you have a question about the MEDIA FLOW CONTROLLER 2.0.4 and is the answer not in the manual?