Red Hat CLUSTER SUITE - CONFIGURING AND MANAGING A CLUSTER 2006 Manual page 41

Chapter 2. Hardware Installation and Operating System Configuration
When using the GRUB boot loader, the timeout parameter in
should be modified to specify the appropriate number of seconds for the timeout param-
eter. To set this interval to 3 seconds, edit the parameter to the following:
timeout = 3
When using the LILO or ELILO boot loaders, edit the
systems) or the
elilo.conf
tenths of a second) for the timeout parameter. The following example sets the timeout
limit to three seconds:
timeout = 30
To apply any changes made to the
mand.
On an Itanium
/boot/efi/efi/redhat/elilo.conf
2.4.3. Displaying Console Startup Messages
Use the command to display the console startup messages. Refer to the dmesg(8)
dmesg
man page for more information.
The following example of output from the
buses and nine disks were detected on the node. (Lines with backslashes display as one
line on most screens):
May 22 14:02:10 storage3 kernel: scsi0 : Adaptec AHA274x/284x/294x \
(EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
May 22 14:02:10 storage3 kernel:
May 22 14:02:10 storage3 kernel: scsi1 : Adaptec AHA274x/284x/294x \
(EISA/VLB/PCI-Fast SCSI) 5.1.28/3.2.4
May 22 14:02:10 storage3 kernel:
May 22 14:02:10 storage3 kernel: scsi : 2 hosts.
May 22 14:02:11 storage3 kernel:
May 22 14:02:11 storage3 kernel: Detected scsi disk sda at scsi0, channel 0, id 0, l
May 22 14:02:11 storage3 kernel:
May 22 14:02:11 storage3 kernel: Detected scsi disk sdb at scsi1, channel 0, id 0, l
May 22 14:02:11 storage3 kernel:
May 22 14:02:11 storage3 kernel: Detected scsi disk sdc at scsi1, channel 0, id 1, l
May 22 14:02:11 storage3 kernel:
May 22 14:02:11 storage3 kernel: Detected scsi disk sdd at scsi1, channel 0, id 2, l
May 22 14:02:11 storage3 kernel:
May 22 14:02:11 storage3 kernel: Detected scsi disk sde at scsi1, channel 0, id 3, l
May 22 14:02:11 storage3 kernel:
May 22 14:02:11 storage3 kernel: Detected scsi disk sdf at scsi1, channel 0, id 8, l
May 22 14:02:11 storage3 kernel:
file (on Itanium systems) and specify the desired value (in
/etc/lilo.conf
system, to apply
file, invoke the
dmesg
Vendor: SEAGATE
Vendor: SEAGATE
Vendor: SEAGATE
Vendor: SEAGATE
Vendor: SEAGATE
Vendor: SEAGATE
Vendor: SEAGATE
/boot/grub/grub.conf
/etc/lilo.conf
file, invoke the
/sbin/lilo
any changes
/sbin/elilo
command shows that two external SCSI
Model: ST39236LW
Model: ST318203LC
Model: ST318203LC
Model: ST318203LC
Model: ST318203LC
Model: ST318203LC
Model: ST318203LC
25
file (on x86
com-
made to the
command.
Rev: 0
Rev: 0
Rev: 0
Rev: 0
Rev: 0
Rev: 0
Rev: 0