Download Print this page

Cisco 12000 - Series Chassis Modular Expansion Base Hardware Installation Manual

Router sip and spa.
Hide thumbs

Advertisement

Cisco 12000 Series Router SIP and SPA
Hardware Installation Guide
June 26, 2006
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-8831-01, Rev. G4

Advertisement

Chapters

Troubleshooting

   Related Manuals for Cisco 12000 - Series Chassis Modular Expansion Base

   Summary of Contents for Cisco 12000 - Series Chassis Modular Expansion Base

  • Page 1

    Cisco 12000 Series Router SIP and SPA Hardware Installation Guide June 26, 2006 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-8831-01, Rev. G4...

  • Page 2

    OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. CCVP, the Cisco Logo, and the Cisco Square Bridge logo are trademarks of Cisco Systems, Inc.; Changing the Way We Work, Live, Play, and Learn is a service mark of Cisco Systems, Inc.;...

  • Page 3: Table Of Contents

    Cisco 12000 SIP-400 Physical Specifications SPA Slot Numbering on the Cisco 12000 SIP-400 SPA Interface Addresses on the Cisco 12000 SIP-400 Cisco 12000 SIP-600 Overview Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 4

    2-Port and 4-Port Channelized T3 SPA Cables and Connectors 8-Port Channelized T1/E1 SPA Overview 8-Port Channelized T1/E1 SPA LEDs 8-Port Channelized T1/E1 SPA Interface Specifications Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 5

    1-Port OC-192c/STM-64 POS/RPR SPA Interface Specifications 2-35 1-Port OC-192c/STM-64 POS/RPR SPA Fixed Optical Transceiver, 40-Pin Connector, and Cables 2-36 Mate Interface Cables 2-36 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 6

    Removing a SIP Installing a SIP Installing and Removing a Shared Port Adapter C H A P T E R Handling SPAs Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 7

    Error Messages FPGA Error Messages SIP Diagnostics Packing a SIP for Shipment Packing a SPA for Shipment 6-10 N D E X Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 8

    Contents Cisco 12000 Series Router SIP and SPA Hardware Installation Guide viii Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 9

    Figure 2-7 Straight-Through Cable Pinout, RJ-45 Connection to a Hub or Repeater 2-12 Figure 2-8 Crossover Cable Pinout, RJ-45 Connections Between Routers 2-12 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 10

    SIP Removal and Installation Figure 4-3 Ejector Levers Figure 5-1 Handling a SPA Figure 5-2 SPA Installation and Removal Figure 5-3 SPA Cable-Management Brackets 5-10 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 11

    T A B L E S Table 1 Document Change History Table xiii Table 1-1 SIP and SPA Compatibility on the Cisco 12000 Series Router Table 1-2 SIP Summary Table 1-3 SIP Hardware and Software Compatibility Table 1-4 Cisco 12000 SIP-400 LED...

  • Page 12

    Commands to Display SPA Information Table 5-3 show Commands to Display SPA Information Table 6-1 Type Options for show logging onboard Command Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 13

    September 22, 2005 Provides descriptions and installation instructions for the following 12.0(31)S2 SPAs installed in a Cisco 12000 SIP-600: 2-Port OC-48c/STM-16 POS SPA • Cisco 12000 Series Router SIP and SPA Hardware Installation Guide xiii Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 14: Table 1 Document Change History Table

    Cisco 12000 SIP-601 was introduced on the Cisco 12000 series router: 8-port OC-12c/STM-4 POS SPA • 12.0(32)SY1 Release September 12, 2006 Support for the following hardware by the Cisco 12000 SIP-501 and 12.0(32)SY1 Cisco 12000 SIP-601 was introduced on the Cisco 12000 series router: 1-Port OC-48c/STM-16 POS SPA •...

  • Page 15: Preface

    This document describes the SPA Interface Processors (SIPs) and shared port adaptors (SPAs) that are supported on the Cisco 12000 series routers. This document also describes how to install the supported SIPs and SPAs and how to troubleshoot the installation.

  • Page 16: Cisco.com

    Cisco products and to view technical documentation in HTML. With the DVD, you have access to the same documentation that is found on the Cisco website without being connected to the Internet. Certain products also have .pdf versions of the documentation available.

  • Page 17: Documentation Feedback

    Register to receive security information from Cisco. • A current list of security advisories and notices for Cisco products is available at this URL: http://www.cisco.com/go/psirt If you prefer to see advisories and notices as they are updated in real time, you can access a Product Security Incident Response Team Really Simple Syndication (PSIRT RSS) feed from this URL: http://www.cisco.com/en/US/products/products_psirt_rss_feed.html...

  • Page 18: Obtaining Technical Assistance

    Use the Cisco Product Identification (CPI) tool to locate your product serial number before submitting Note a web or phone request for service. You can access the CPI tool from the Cisco Technical Support & Documentation website by clicking the Tools & Resources link under Documentation & Tools. Choose Cisco Product Identification Tool from the Alphabetical Index drop-down list, or click the Cisco Product Identification Tool link under Alerts &...

  • Page 19: Submitting A Service Request

    Cisco engineer. The TAC Service Request Tool is located at this URL: http://www.cisco.com/techsupport/servicerequest For S1 or S2 service requests or if you do not have Internet access, contact the Cisco TAC by telephone. (S1 or S2 service requests are those in which your production network is down or severely degraded.) Cisco engineers are assigned immediately to S1 and S2 service requests to help keep your business operations running smoothly.

  • Page 20

    Preface Obtaining Additional Publications and Information Cisco Press publishes a wide range of general networking, training and certification titles. Both new • and experienced users will benefit from these publications. For current Cisco Press titles and other information, go to Cisco Press at this URL: http://www.ciscopress.com...

  • Page 21: Sip And Spa Compatibility

    Cisco 12000 SIP-601 Overview, page 1-18 • SIP and SPA Compatibility Table 1-1 shows the SPAs that are supported on the Cisco 12000 series router and the SIPs that support them: Table 1-1 SIP and SPA Compatibility on the Cisco 12000 Series Router SIP Type 2.5G ISE SIP...

  • Page 22: Router Hardware Installation

    SIPs. Supported Platforms SIPs are supported on all Cisco 12000 series routers. The 2.5G ISE SIP is supported on the Cisco 12016, 124xx, and 128xx routers. The Cisco 12000 SIP-401, the Cisco 12000 SIP-501, the Cisco 12000 SIP-600, and the Cisco 12000 SIP-601are supported on the Cisco 124xx and 128xx routers.

  • Page 23: Table 1-2 Sip Summary

    SIP Software and Hardware Compatibility For software configuration information, refer to the Cisco IOS software configuration and command reference publications for the installed Cisco IOS release. Also refer to the Cisco IOS software release notes for additional information. Table 1-3 lists the Cisco IOS releases that are compatible with supported SIPs.

  • Page 24: Cisco 12000 Sip-400 Overview

    For complete descriptions of show commands, refer to the Cisco IOS Configuration Fundamentals Configuration Guide and the Cisco IOS Configuration Fundamentals Command Reference for the installed Cisco IOS release.

  • Page 25: Figure 1-1 Cisco 12000 Sip-400 Board-rear View

    Four packet memory SODIMM sockets (not field serviceable) Backplane connector Four TLU/PLU memory SODIMM sockets (not field serviceable) Route memory SODIMM Cisco 12000 SIP-400 LEDs The Cisco 12000 SIP-400 has one LED, as shown in Figure 1-2. Figure 1-2 Cisco 12000 SIP-400 Face Plate SPA subslot 0...

  • Page 26: Cisco 12000 Sip-400 Leds

    The Cisco 12000 SIP-400 accepts 4 single-width, single-height SPAs. Figure 1-3 shows a Cisco 12000 SIP-400 with 4 SPAs installed. The top leftmost SPA slot is subslot 0; the top rightmost SPA slot is subslot 1; the bottom leftmost SPA slot is subslot 2; the bottom rightmost SPA slot is subslot 3.

  • Page 27: Spa Interface Addresses On The Cisco 12000 Sip-400

    SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco 12000 SIP-400 has four subslots. A 4-port SPA would have ports 0 to 3. For example, the interface address of the second port on a 4-port SPA located in the first SIP subslot, where the SIP is inserted into router line card slot 6 is 6/0/1.

  • Page 28: Cisco 12000 Sip-600 Overview

    Cisco 12000 SIP-600 LEDs The Cisco 12000 SIP-600 supports 2 single-width, double-height SPAs, 2 single-width, single-height SPAs, or 1 dual-width, double-height SPA. The Cisco 12000 SIP-600 face plate has one Status LED. Figure 1-6 shows the Cisco 12000 SIP-600 face plate with 2 single-width, single-height SPAs.

  • Page 29: Table 1-6 Cisco 12000 Sip-600 Leds

    Figure 1-7 shows a Cisco 12000 SIP-600 with 2 SPAs installed. The left SPA slot is subslot 0 and the right SPA slot is subslot 1. If one dual-width SPA is installed, it is recognized as being in subslot 0.

  • Page 30: Figure 1-8 Slot, Subslot, And Port Locations For The 1-port 10-gigabit Ethernet Spa And The 10-port Gigabit Ethernet

    SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco 12000 SIP-600 has two subslots 0 (left) and 1 (right). For example, the interface address of a 1-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 is 3/1/0.

  • Page 31: Cisco 12000 Sip-401 Overview

    Cisco 12000 SIP-401 LEDs, page 1-11 • Cisco 12000 SIP-401 Physical Specifications, page 1-12 • SPA Slot Numbering on the Cisco 12000 SIP-401, page 1-12 • SPA Interface Addresses on the Cisco 12000 SIP-401, page 1-13 • Cisco 12000 SIP-401 Board Components...

  • Page 32: Cisco 12000 Sip-401 Physical Specifications

    Rate SIP is SIP-401 or SIP-501. Green SIP is SIP-601. Cisco 12000 SIP-401 Physical Specifications The Cisco 12000 SIP-401 physical specifications are shown in the following table. Table 1-11 Cisco 12000 SIP-401 Physical Specifications Description Specifications Physical dimensions Occupies one line card slot on a Cisco 12000 Series Router...

  • Page 33: Spa Interface Addresses On The Cisco 12000 Sip-401

    SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco 12000 SIP-401 has four subslots. A 4-port SPA would have ports 0 to 3. For example, the interface address of the second port on a 4-port SPA located in the first SIP subslot, where the SIP is inserted into router line card slot 6 is 6/0/1.

  • Page 34: Cisco 12000 Sip-501 Overview

    Chapter 1 Overview: Cisco 12000 Series Router SPA Interface Processors Cisco 12000 SIP-501 Overview Figure 1-12 Cisco 12000 Series Router with Cisco 12000 SIP-401 Installed MBUS ALAR M A FAIL ALAR M B ENABLE 12000-SIP -600 Router slot number 6...

  • Page 35: Cisco 12000 Sip-501 Board Components

    SPA. If the maximum capacity of a SPA is 2.5Gbps or less the interconnect operates at 2.5Gbps and the SPA is a "quarter-rate" SPA. The Cisco 12000 SIP-501 can support up to two full-rate SPAs, or one full-rate and three quarter-rate SPAs or four quarter-rate SPAs.

  • Page 36: Cisco 12000 Sip-501 Physical Specifications

    Figure 1-15 shows a Cisco 12000 SIP-501 with 2 SPAs installed. The left SPA slot is subslot 0 and the right SPA slot is subslot 1. If one dual-width SPA is installed, it is recognized as being in subslot 0.

  • Page 37: Spa Interface Addresses On The Cisco 12000 Sip-501

    SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco 12000 SIP-601 has two subslots 0 (left) and 1 (right). For example, the interface address of a 1-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 is 3/1/0.

  • Page 38: Cisco 12000 Sip-601 Overview

    SPA enclosure Backplane connector Cisco 12000 SIP-601 LEDs The Cisco 12000 SIP-601 supports 4 single-height SPAs (the aggregate throughput should not exceed 2 full-rate SPAs); 2 double-height SPAs; 1 dual-width, double-height SPA, or a combination of single-height and double-height SPAs.

  • Page 39: Figure 1-18 Cisco 12000 Sip-601 Face Plate

    SPA. If the maximum capacity of a SPA is 2.5Gbps or less the interconnect operates at 2.5Gbps and the SPA is a "quarter-rate" SPA. The Cisco 12000 SIP-601 can support up to two full-rate SPAs, or one full-rate and three quarter-rate SPAs or four quarter-rate SPAs.

  • Page 40: Spa Subslot Numbering On The Cisco 12000 Sip-601

    SPA, in the format slot/subslot/port. Subslots and ports are numbered starting from 0, so each Cisco 12000 SIP-601 has two subslots 0 (left) and 1 (right). For example, the interface address of a 1-port SPA located in the second SIP subslot, where the SIP is inserted into router line card slot 3 is 3/1/0.

  • Page 41: Figure 1-20 Slot, Subslot, And Port Locations For The 1-port 10-gigabit Ethernet Spa And The 10-port Gigabit Ethernet

    Table 1-19 Slot and Port Locations for the 1-Port 10-Gigabit Ethernet SPA Call Out Number Description Slot 3 Subslot 0, Port 3/0/0 Subslot 1, Ports 3/1/0 to 3/1/9 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 1-21 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 42

    Chapter 1 Overview: Cisco 12000 Series Router SPA Interface Processors Cisco 12000 SIP-601 Overview Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 1-22 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 43: Spa Summary

    Overview: Cisco 12000 Series Router Shared Port Adapters Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007 This chapter describes the shared port adapters (SPAs) that are supported on the Cisco 12000 Series Router and contains the following sections: SPA Summary, page 2-1 •...

  • Page 44: C H A P T E R 2 Overview: Cisco 12000 Series Router Shared Port Adapters

    To check the minimum software requirements of Cisco IOS software with the hardware installed on your router, Cisco maintains the Software Advisor tool on Cisco.com. This tool does not verify whether SIPs or SPAs within a system are compatible, but it does provide the minimum Cisco IOS requirements for individual hardware modules or components.

  • Page 45: Bandwidth Oversubscription

    Access to this tool is limited to users with Cisco.com login accounts. Note To access Software Advisor, click Login at Cisco.com, type “Software Advisor” in the SEARCH box, and click GO. Click the link for the Software Advisor tool. Choose a product family or enter a specific product number to search for the minimum supported software release needed for your hardware.

  • Page 46: 2-port And 4-port T3/e3 Serial Spa Overview

    A/L (Active Loopback) LED STATUS LED TX (Transmit) connector The 2-Port and 4-Port Clear Channel T3/E3 SPA LEDs are described in Table 2-3. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 47: 2-port And 4-port Clear Channel T3/e3 Spa Interface Specifications

    CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 feet) • • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) The Cisco cable part numbers are 72-4124-01 (with male BNC end) and 72-4131-01 (with female BNC Note end). Figure 2-1...

  • Page 48: 2-port And 4-port Channelized T3 To Ds0 Spa Overview

    Figure 2-2 4-Port Channelized T3 SPA Faceplate SPA-4XCT3/DS0 C/A (Carrier/Alarm) LED RX (Receive) connector A/L (Active Loopback) LED STATUS LED TX (Transmit) connector Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 49: 2-port And 4-port Channelized T3 Spa Interface Specifications

    CAB-T3E3-RF-BNC-F (T3 or E3 Cable, 1.0/2.3 RF to BNC-Female, 10 feet) • CAB-T3E3-RF-OPEN (T3 or E3 Cable, 1.0/2.3 RF to BNC-Open end, 10 feet) • The Cisco cable part numbers are 72-4124-01 (with Male BNC end) and 72-4131-01 (with Female BNC Note end). Figure 2-2...

  • Page 50: 8-port Channelized T1/e1 Spa Overview

    8-Port Channelized T1/E1 SPA Faceplate C/A (Carrier/Alarm) LED STATUS LED A/L (Active Loopback) LED The 8-Port Channelized T1/E1 SPA LEDs are described in Table 2-7. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 51: 8-port Channelized T1/e1 Spa Interface Specifications

    RJ-45 cable connectors. Table 2-8 RJ-45 Connector Pinouts Signal Description RX– Receive ring – Receive tip + Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 52: 8-port Fast Ethernet Spa Overview

    Port is enabled and the link is up. 5, 6 or 7) Amber Port is enabled and the link is down. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-10 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 53: 8-port Fastethernet Spa Cables, Connectors, And Pinouts

    The interface connectors on the 8-Port FastEthernet SPA are eight individual RJ-45 receptacles. You can use all eight interface connectors simultaneously. Each connection supports IEEE 802.3 and Ethernet 10/100BASE-T interfaces compliant with appropriate standards. Cisco Systems does not supply Category 5 unshielded twisted-pair (UTP) RJ-45 cables; these cables are available commercially.

  • Page 54: 1-port 10-gigabit Ethernet Spa Overview

    1-Port 10-Gigabit Ethernet SPA LEDs, page 2-13 • 1-Port 10-Gigabit Ethernet SPA XFP Optical Transceiver Modules, Connectors, and Cables, page • 2-13 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-12 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 55: 1-port 10-gigabit Ethernet Spa Leds

    Single-mode long-reach (LR) XFP module—XFP-10GZR • Cisco Systems qualifies the optics that are approved for use with its SPAs. As of the above listed small form-factor pluggable (XFPs) are the only optical transceiver modules qualified for use. Use a single-mode optical fiber that has a modal-field diameter of 8.7 ±0.5 microns (nominal diameter is approximately 10/125 microns) to connect your router to a network.

  • Page 56: Xfp Connections

    Figure 2-10 LC-Type Cable for the XFP Optical Transceiver Modules The 40-pin connector on the 1-Port 10-Gigabit Ethernet SPA is used for resilient packet ring (RPR) Note connections. This feature is not supported in Cisco IOS Release 12.0(32)SY. XFP Connections The XFP-10GLR-OC192SR, XFP-10GER-OC192IR, and XFP-10GZR-OC192LR XFPs include an optical transmitter and receiver pair integrated with Clock and Data Recovery (CDR) integrated circuits.

  • Page 57: Xfp Port Cabling Specifications

    The following sections describe the 2-Port Gigabit Ethernet SPA: 2-Port Gigabit Ethernet SPA LEDs, page 2-16 • • SFP Module Cabling and Connection Equipment, page 2-18 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-15 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 58: 2-port Gigabit Ethernet Spa Leds

    An SFP module check is run every time an SFP module is inserted into the 2-Port Gigabit Ethernet SPA and only SFP modules that pass this check will be usable by the 2-Port Gigabit Ethernet SPA. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-16...

  • Page 59: Table 2-14 Sfp Module Options

    SFP-GE-Z: –40 to 185 degrees F (–40 to 85 degrees C) Supply voltage range SFP-GE-S: 3.1 to 3.5 V SFP-GE-L: 3.1 to 3.5 V SFP-GE-Z: 3.1 to 3.5 V Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-17 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 60: Sfp Module Cabling And Connection Equipment

    SFP-GE-Z is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the SFP-GE-Z is 24.9 miles (40 km). Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-18...

  • Page 61: 5-port Gigabit Ethernet Spa Overview

    The following sections describe the 5-Port Gigabit Ethernet SPA: • 5-Port Gigabit Ethernet SPA LEDs, page 2-20 • 5-Port Gigabit Ethernet SPA Cables and Connectors, page 2-20 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-19 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 62: 5-port Gigabit Ethernet Spa Leds

    Gigabit Ethernet SPA. However, the information in this document pertains only to SFP modules that plug into the 5-Port Gigabit Ethernet SPA ports. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-20 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 63: Table 2-18 Sfp Module Options

    The 1000BASE-SX (short-wavelength) module operates on standard multimode fiber-optic link spans of up to 500 m on 50/125um multimode fiber (MMF) and 300 m on 62.5/125um MMF. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-21 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 64: Sfp Module Cabling And Connection Equipment

    SFP-GE-Z is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the SFP-GE-Z is 24.9 miles (40 km). Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-22...

  • Page 65: 10-port Gigabit Ethernet Spa Overview

    The following sections describe the 10-Port Gigabit Ethernet SPA: 10-Port Gigabit Ethernet SPA LEDs, page 2-24 • 10-Port Gigabit Ethernet SPA Cables and Connectors, page 2-24 • Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-23 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 66: 10-port Gigabit Ethernet Spa Leds

    The small form-factor pluggable (SFP) module is an input/output (I/O) device that plugs into the Gigabit Ethernet optical slots on the 10-Port Gigabit Ethernet SPA, linking the port with a 1000BASE-X fiber-optic network. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-24 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 67: Table 2-22 Sfp Module Options

    SFP-GE-Z: –40 to 185 degrees F (–40 to 85 degrees C) Supply voltage range SFP-GE-S: 3.1 to 3.5 V SFP-GE-L: 3.1 to 3.5 V SFP-GE-Z: 3.1 to 3.5 V Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-25 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 68: Sfp Module Cabling And Connection Equipment

    SFP-GE-Z is 6.2 miles (10 km) with an 8-dB attenuator installed at each end of the link. Without attenuators, the minimum link distance for the SFP-GE-Z is 24.9 miles (40 km). Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-26...

  • Page 69: 1-port Channelized Stm-1/oc-3 Spa Overview

    1-Port Channelized STM-1/OC-3 SPA LEDs, page 2-28 • 1-Port Channelized STM-1/OC-3 SPA Interface Specifications, page 2-28 • 1-Port Channelized STM-1/OC-3 SPA Cables and Connectors, page 2-29 • Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-27 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 70: 1-port Channelized Stm-1/oc-3 Spa Leds

    OC-3c/STM-1 line rates (155.52 Mbps). Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the STS-3c/STM-1 frame. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-28 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 71: 1-port Channelized Stm-1/oc-3 Spa Cables And Connectors

    Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-29 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 72: 1-port Oc-48c/stm-16 Pos Spa Overview

    The 1-Port OC-48c/STM-16 POS SPA is a single-height SPA that is installed in a SIP subslot. The 1-Port OC-48c/STM-16 POS SPA provides RPR over SONET (IEEE 802.17), SRP over SONET (Cisco Proprietary), and Packet over SONET (POS) network connectivity with a bandwidth of 9.95 Gbps.

  • Page 73: 1-port Oc-48c/stm-16 Pos Spa Interface Specifications

    Packet data is transported with a user-configured encapsulation (such as Point-to-Point Protocol [PPP]) and is mapped into the STS-48/STM-64 frame. The 1-Port OC-48c/STM-16 POS SPA interface is compliant with the following RFCs: Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-31 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 74: 1-port Oc-48c/stm-16 Pos Spa Optical Transceiver Modules, Connectors, And Cables

    Mate Interface Cables The 1-Port OC-48c/STM-16 POS SPA supports two mate interface configurations: • Mate between two OC-48c SPAs in the same SIP Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-32 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 75: 1-port Oc-192c/stm-64 Pos Spa Overview

    For more information about SPAs and their compatibility with SIPs and modular optics, see the “SIP and SPA Compatibility” chapter in this guide. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-33 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 76: 1-port Oc-192c/stm-64 Pos/rpr Spa Leds

    Port is in wrap mode somewhere on the ring. Amber Port is in wrap mode locally. PASSTHRU Port is not in pass-thru mode. Amber Port is in pass-thru mode. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-34 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 77: 1-port Oc-192c/stm-64 Pos/rpr Spa Interface Specifications

    RFC 1157, Simple Network Management Protocol (SNMP) • RFC 1213, Management Information Base (MIB) for Network Management of TCP/IP-Based • Internets:MIB II Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-35 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 78: Mate Interface Cables

    (TX), for SONET and SDH connection to the network. In Cisco IOS Release 12.0(31)S, only long-reach (LR) optics are supported. Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS Release 12.0(31)S Cisco IOS XR Software Release 3.2, the XFP-10GLR-OC192SR and the XFP-10GER-OC192IR are the only optical transceiver modules qualified for use.

  • Page 79: 1-port Oc-192c/stm-64 Pos Rpr Xfp Spa Overview

    1-Port OC-192c/STM-64 POS/RPR SPA Interface Specifications, page 2-35 • • 1-Port OC-192c/STM-64 POS/RPR SPA Fixed Optical Transceiver, 40-Pin Connector, and Cables, page 2-36 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-37 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 80: 1-port Oc-192c/stm-64 Pos/rpr Xfp Spa Leds

    Port is enabled by software, and there is at least one alarm (LOS, LOF, RDI, and so on). Blinking SRP mode mismatch alarm is indicated. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-38 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 81: 1-port Oc-192c/stm-64 Pos/rpr Xfp Spa Interface Specifications

    Single-mode very-long reach XFP module—XFP-10GZR-OC192LR • Cisco Systems qualifies the optics that are approved for use with its SPAs. As of Cisco IOS Release 12.0(31)S, the above-listed XFPs are the only optical transceiver modules qualified for use. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-39 Release 12.0(32)SY1, OL-8831-01, Rev.

  • Page 82: Oc-192 Module Connections

    Figure 2-25 LC-Type Cable for the XFP Optical Transceiver Modules The 40-pin connector on the 1-Port OC-192c/STM-64 POS/RPR XFP SPA is used for resilient packet Note ring (RPR) connections. This feature is not supported in Cisco IOS Release 12.0(31)S. OC-192 Module Connections Table 2-29 shows the OC-192 specifications for use with the 1-Port OC-192c/STM-64 POS/RPR XFP SPA.

  • Page 83: Mate Interface Cables

    Support for the RPR feature is dependent on the platform software release feature content. Verify support for the RPR feature support via SPA datasheets or by contacting your Cisco representative. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-41 Release 12.0(32)SY1, OL-8831-01, Rev.

  • Page 84: 2-port Oc-48 Pos Rpr Spa Overview

    A node on the ring is wrapped. Green Blinking A node on the ring is steering pass-through Amber Port is locally wrapped Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-42 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 85: 2-port Oc48-pos/rpr Spa Interface Specifications

    2-28) or two simplex LC-type cables, one for transmit (TX) and one for receive (RX). Figure 2-28 Duplex Patch Cable with LC-Type Connectors Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-43 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 86: Port Oc-3c/stm-1 Pos Spa Overview

    OC-3c/STM-1 POS SPA have three LEDs: two LEDs for each port on the SPA and one STATUS LED. Figure 2-29 shows the 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA faceplate. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-44 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 87: Oc-3c/stm-1 Pos Spa Leds

    The 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA and the 4-Port and 8-Port OC-3c/STM-1 POS SPA interface complies with the following IETF RFCs: Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-45 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 88: Figure 2-30 Sfp Optics Module

    Figure 2-30). Cisco Systems qualifies the optics that are approved for use with its SPAs. The 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA when configured as OC-3 and the 4-Port and 8-Port OC-3c/STM-1 POS SPA support the following types of optical transceiver modules: •...

  • Page 89: Figure 2-31 Lc-type Cable

    Long-range SFP optical transceiver modules (for long-reach configurations) cannot be connected back-to-back without using an attenuator between the two of them. Figure 2-31 LC-Type Cable Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-47 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 90

    Overview: Cisco 12000 Series Router Shared Port Adapters 2-Port, 4-Port, and 8-Port OC-3c/STM-1 and OC-12c/STM-4 POS SPA, 4-Port OC-3c/STM-1 POS SPA, and 8-Port Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 2-48 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 91: Required Tools And Equipment

    Safety Warnings, page 3-2 • Electrical Equipment Guidelines, page 3-6 • • Electrical Equipment Guidelines, page 3-6 • Telephone Wiring Guidelines, page 3-7 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 92: C H A P T E R 3 Preparing To Install A Spa Interface Processor Or A Shared Port Adapter

    Safety Warnings Review the safety warnings listed in the Regulatory Compliance and Safety Information for Cisco 12000 Series Internet Routers before installing, configuring, or troubleshooting any installed SIP or SPA. Safety warnings appear throughout this publication in procedures that, if performed incorrectly, might harm you.

  • Page 93

    Utilize o número da instrução fornecido ao final de cada aviso para localizar sua tradução nos avisos de segurança traduzidos que acompanham este dispositivo. GUARDE ESTAS INSTRUÇÕES Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 94

    Använd det nummer som finns i slutet av varje varning för att hitta dess översättning i de översatta säkerhetsvarningar som medföljer denna anordning. SPARA DESSA ANVISNINGAR Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 95

    Chapter 3 Preparing to Install a SPA Interface Processor or a Shared Port Adapter Safety Guidelines Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 96: Electrical Equipment Guidelines

    • power-off switch for the room in which you are working. • Disconnect all power and external cables before moving a chassis. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 97: Telephone Wiring Guidelines

    ESD voltages on the body; ESD voltages on clothing can still cause damage. • Never attempt to remove the printed circuit board from the metal carrier. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 98: Laser/led Safety

    Det kan forekomme usynlig laserstråling fra fiber eller kontakter som er frakoblet. Stirr ikke direkte inn i strålene eller se på dem direkte gjennom et optisk instrument. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 99

    ópticos. Advarsel Usynlig laserstråling kan forekomme fra brugte fibre eller stik. Stir ikke ind i stråler eller direkte med optiske instrumenter. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 100

    Invisible laser radiation may be emitted from disconnected fibers or connectors. Do not stare into Warning beams or view directly with optical instruments. Statement 1051 Warning Class 1 LED product. Statement 1027 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 3-10 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 101: Chapter 4 Installing And Removing A Spa Interface Processor

    Installing and Removing a SPA Interface Processor Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007 This chapter describes how to install or remove SIPs on the Cisco 12000 series router. This chapter contains the following sections: Handling SIPs, page 4-1 •...

  • Page 102: Removing And Installing A Sip

    • Installing a SIP • Some of the procedures in the following sections use illustrations of a Cisco 12012 Router to support the Note descriptions of removing and installing SIPs. Although the card cages of Cisco 12000 Series Routers differ, the designated use of slots and the process of installing and removing a SIP are basically the same.

  • Page 103: Removing A Sip

    Step 3 Step 4 Use a screwdriver to loosen the captive installation screw at each end of the SIP faceplate. (See Figure 4-2a.) Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 104: Figure 4-2 Sip Removal And Installation

    SIP compartment. Secure the SIP blank filler plate to the chassis by tightening its captive installation screws. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 105: Installing A Sip

    Figure 4-3 Ejector Levers When inserting a card, make re that the ejector lever hooks catch the lip of the card cage. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 106

    Install the SFP modules in the SPAs that use them. Refer to Chapter 5, “Installing and Removing a Shared Port Adapter”. Step 9 Install the interface cables. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 107: Chapter 5 Installing And Removing A Shared Port Adapter

    Installing and Removing a Shared Port Adapter Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007 This chapter describes how to install or remove SPAs on the Cisco 12000 series router. This chapter contains the following sections: Handling SPAs, page 5-1 •...

  • Page 108: Spa Installation And Removal

    Grasp the handle of the SPA and pull the SPA from the SIP. (Ensure that you have already disconnected the cables from the SPA before removing the SPA from the SIP). Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 109: Online Insertion And Removal

    AT M Online Insertion and Removal Cisco 12000 series router SIPs and SPAs support online insertion and removal (OIR). SPAs can be inserted or removed independently from the SIP. OIR of a SIP with installed SPAs is also supported. Optical Device Installation and Removal Any contamination of the fiber connection can cause failure of the component or failure of the whole system.

  • Page 110: Cleaning Optical Devices

    00:07:36:%LINEPROTO-5-UPDOWN:Line protocol on Interface pos4/0/0, changed state to up Use the following procedure to verify that a SIP and SPA are installed correctly: Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 111: Using Show Commands To Verify Sip And Spa Status

    When the SIP and SPA STATUS LEDs are green, all associated interfaces are configurable. • Refer to the Cisco 12000 Series Router SIP and SPA Software Configuration Guide (Cisco IOS) for configuration instructions. If a SIP or SPA is replaced with a module of the same type (as in an OIR or hardware swap), the •...

  • Page 112: Using Show Commands To Display Spa Information

    For more information about FPD upgrades, refer to the “Upgrading Field-Programmable Devices” chapter of the Cisco 7600 Series Router SIP, SSC, and SPA Software Configuration Guide. Use the show version command to obtain a few details on the installed SIPs and interfaces available.

  • Page 113

    If the ENABLED LED fails to go on, remove the SIP and ensure the SPA is firmly seated in its slot. • Remove and reinstall it accordingly. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 114: Using The Ping Command To Verify Network Connectivity

    Suspect a faulty SIP. Contact a service representative to report the problem and obtain further instructions. Step 5 If the SPA is new and not a replacement, configure the new SPA using the Cisco 12000 Series Router SIP and SPA Software Configuration Guide (Cisco IOS). New interfaces are not available until you configure them.

  • Page 115: Spa Blank Filler Plates

    SPAs. If you plan to install a new SPA in a subslot that is not in use, you must first remove the SPA blank filler plate. Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 116: Spa Cable-management Brackets

    To remove the cable-management clip, depress the button on the clip and pull it out. Blank filler plugs are provided if no cable-management clips are installed. Note Cisco 12000 Series Router SIP and SPA Hardware Installation Guide 5-10 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 117: Chapter 6 Troubleshooting The Installation

    Troubleshooting the Installation Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007 This chapter describes how to troubleshoot the installation of SIPs and SPAs on the Cisco 12000 series router. This chapter contains the following sections: Using show Commands to Check Status, page 6-1 •...

  • Page 118: Advanced Sip Troubleshooting

    Output from these commands will vary slightly depending on which SIP you are using, but the basic information will be the same. Output Examples The following are examples of system output that you may see if your Cisco 12000 series router SIP fails. Key data in the output is underlined. show context summary Output •...

  • Page 119: Show Context Summary Output

    Temperature after last boot in location #1: inlet 27 C, hotpoint 37 C <=== Crash at Aug 08 2004 11:10:37 ===> <===End Crash ===> Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 120: Table 6-1 Type Options For Show Logging Onboard Command

    FrFab SDRAM size: 134217728 bytes, SDRAM pagesize: 8192 bytes ToFab SDRAM size: 134217728 bytes, SDRAM pagesize: 8192 bytes 1 crash since restart Cisco 12000 Series Router SIP and SPA Hardware Installation Guide Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 121: Checking The Current Status Of The Sip

    In the example above, the SIP has failed and has caused a reload because of a software forced crash exception. Once you have determined the cause and collected the necessary output, you can check for any caveats in your Cisco IOS software release using the Bug Toolkit (available to registered Cisco.com users only).

  • Page 122: Fabric Ping Failure

    If you receive any error message related to a SIP, you can use the Error Message Decoder Tool (on Cisco.com) to find the meaning of this error message. Some errors point to a hardware issue, while others indicate a Cisco IOS software caveat or a hardware issue on another part of the router. This document does not cover all these messages.

  • Page 123: Fpga Error Messages

    12000 Series Internet Router document. When the Cisco IOS image boots, it verifies that a compatible FPGA image is running on the router. The major version number of the FPGA image must be the same as that expected by the Cisco IOS image;...

  • Page 124

    This image must be available on a separate Flash memory card, Flash disk, or TFTP boot server in order to load SIP field diagnostics. The latest version is always available on Cisco.com. RP and fabric tests remain embedded within the main Cisco IOS software image.

  • Page 125: Packing A Sip For Shipment

    Larger exterior carton • Two packing cushions • Use Cisco Systems original packaging for the shipment of all SIPs. Failure to properly use Cisco Caution Systems packaging can result in damage or loss of product. Warning During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly touch the backplane with your hand or any metal tool, or you could shock yourself.

  • Page 126: Packing A Spa For Shipment

    • Carton • The Cisco Systems original packaging is to be used for the shipment of all SPAs and cable-management Caution brackets. Failure to properly use Cisco Systems packaging can result in damage or loss of product. During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly Warning touch the backplane with your hand or any metal tool, or you could shock yourself.

  • Page 127

    SIPs and SPAs must have the right FPD version to function properly; an FPD incompatibility will disable all interfaces on the SPA or all SPAs within the SIP. An FPD image package is used to upgrade FPD images. Whenever a Cisco IOS image is released that FPD image package supports SPAs, a companion SPA FPD image package is also released for that Cisco IOS software release.

  • Page 128

    Secondary slot on a SIP where a SPA is installed. The primary slot is the chassis slot on the router. subslot Cisco 12000 Series Router SIP and SPA Hardware Installation Guide GL-2 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 129

    LEDs Compatibility 2-Port and 4-Port Clear Channel T3/E3 SPA SIP, SPA Cables and Connectors connectors Interface Specifications SC type (figure) 2-36 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide IN-1 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 130

    1-5, 1-12, 1-16, 1-19 for OC-192c/STM-64 POS/RPR SPA 2-36 long reach organization, document optical transceiver module 2-46 SFP module 2-43 prerequisites VIP installation Cisco 12000 Series Router SIP and SPA Hardware Installation Guide IN-2 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 131

    SFP (small form-factor pluggable) optics slot numbering 1-6, 1-12 2-Port Gigabit Ethernet SPA 2-16 SPA (shared port adapter) SFP-GE-L 2-22, 2-26 Cable management brackets 5-10 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide IN-3 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

  • Page 132

    2-37, 2-39 intermediate reach 2-13, 2-39 long reach 2-13 short reach 2-13 XFP optical transceiver modules for OC-192c/STM-64 POS/RPR XFP SPA 2-43 Cisco 12000 Series Router SIP and SPA Hardware Installation Guide IN-4 Release 12.0(32)SY1, OL-8831-01, Rev. G6, July 19, 2007...

This manual also for:

Gsr12/60-rf - 12012 router, 12000 series

Comments to this Manuals

Symbols: 0
Latest comments: