Table of Contents
Advertisement
Quick Links
IMPORTANT INFORMATION:
• A copy of our "Safe Operating Practices" Manuals are always available free of charge either by downloading it from our
Technical Publications website @ www.airwinch.com or by contacting the Factory at (800) 866-5457 for North America and
(206) 624-0466 for International. The Safe Operating Practices manual must be read prior to anyone operating a
Ingersoll-Rand winch or hoist. The manual form numbers are as follows:
"Safe Operating Practices Non-Man Rider™ Winches" Manual, Form No. MHD56250
"Safe Operating Practices for Man Rider™ Winches" Manual, Form No. MHD56251
"Safe Operating Practices for Pneumatic, Hydraulic and Electric Hoists" Manual, Form No. MHD56295
• Available winch options may require additional supplements to the basic winch manual.
• For Man Rider™ winches ensure a copy of the Man Rider™ supplement is made available to the operator prior to winch
operation.
Winch Man Rider
™
Model:
FA2, FA2.5,
FH2, FH2.5
FA5
FA10
FA2.5A
FA2B and
HU40A
FH10MR
Fulcrum Electric
LS500HLP/
LS1000HLP
• We strongly recommend that ALL maintenance on Ingersoll-Rand equipment be carried out by personnel certified by
Ingersoll-Rand, or by Ingersoll-Rand Authorized Service Centers.
• Contact the Factory if in doubt about installation, operation, inspection and maintenance instructions.
• Use only Genuine Ingersoll-Rand parts when maintaining or repairing a winch, hoist or any component of a winch or hoist.
• ANSI / ASME recommends that a winch or hoist (or any components of a winch or hoist) that has been repaired be tested
prior to being placed into service:
*
Winches - ANSI / ASME B30.7 (BASE MOUNTED DRUM HOISTS) Refer to section 7.2.2 - Testing.
*
Hoists - ANSI / ASME B30.16 (OVERHEAD HOISTS - UNDERHUNG) Refer to section 16.2.2 - Testing.
Form MHD56298
Edition 2
November 2004
71441844
© 2004 Ingersoll-Rand Company
Supplements:
Publication No.
MHD56046
MHD56042 and
MHD56220
MHD56252
MHD56236
MHD56207
MHD56212
MHD56277
SAM0004
Model:
Publication No.
LS500RLP
LS1000RLP
LS150RLP
LS150RLP/500/
1000
LS150RLP and
LS150PLP-PH
LS500RLP-E
LS150RLP-
DP5M-F
LS150HLP
Form MHD56298
SAM0011
SAM0012
SAM0082
SAM0115
SAM0120
SAM0122
SAM0184
SAM0222
Advertisement
Table of Contents
Related Manuals for Ingersoll-Rand force 5 FA150KGMR-RC MAN RIDER
Summary of Contents for Ingersoll-Rand force 5 FA150KGMR-RC MAN RIDER
- Page 1 • Contact the Factory if in doubt about installation, operation, inspection and maintenance instructions. • Use only Genuine Ingersoll-Rand parts when maintaining or repairing a winch, hoist or any component of a winch or hoist. • ANSI / ASME recommends that a winch or hoist (or any components of a winch or hoist) that has been repaired be tested prior to being placed into service: Winches - ANSI / ASME B30.7 (BASE MOUNTED DRUM HOISTS) Refer to section 7.2.2 - Testing.
- Page 2 Make this manual available to all persons responsible for the installation, operation and maintenance of these products. This manual applies only to FA150KGMR-RC winches designed by Ingersoll-Rand that are identified for personnel lifting by a permanent nameplate attached to the winch at the factory.
-
Page 3: Table Of Contents
CONTENTS Description Page No. Safety Information Danger, Warning, Caution and Notice .................................3 Safety Summary........................................3 General Information Operating Limitations ......................................4 Traceability ..........................................4 Winch Operating Instructions Man Rider Operating Instructions..................................5 Warning Labels ........................................6 Specifications Description...........................................7 Installation Mounting..........................................10 Wire Rope ..........................................10 Air Supply..........................................13 Initial Winch Operating Checks..................................14 Operation Training..........................................17... -
Page 4: Safety Information
• The supporting structures and load-attaching devices used in Ingersoll-Rand cannot know of, or provide all the procedures by conjunction with this winch must provide an adequate safety which product operations or repairs may be conducted and the factor to handle the rated load, plus the weight of the winch hazards and/or results of each method. -
Page 5: General Information
GENERAL INFORMATION Ingersoll-Rand offers, in its winch product line, a limited number The personnel platform shall be designed by a registered of models referred to as Man Rider which are designed and engineer competent in this area. manufactured to standards and specifications based on the recommendations of various regulatory bodies for the purpose of lifting people. -
Page 6: Man Rider Operating Instructions
Ingersoll-Rand assumes no liability for any loss or damage resulting from operation of Ingersoll-Rand recognizes that most companies who use winches Man Rider winches if these operating instructions are not have a safety program in force at their facility. In the event that followed. -
Page 7: Warning Labels
WARNING LABELS Each unit is shipped from the factory with warning labels shown. If labels are not attached to your unit, order new labels and install. Refer to parts list for part numbers. Labels are shown smaller than actual size. Failure to follow these warnings can result in severe injury, death or... -
Page 8: Specifications
SPECIFICATIONS Output from the externally mounted gear air motor is transmitted Description through a disc brake to the planetary reduction gear assembly. The output from the planetary reduction gear assembly is FA150KGMR-RC winches are air powered, planetary geared connected to the wire rope drum through the drum carrier. units designed for transporting personnel. - Page 9 Rated Operating Pressure 75 psig (5.8 bar/580 kPa) System Air Consumption (at rated pressure and load) 75 scfm 2.1 cu.m/min Full Drum Line Pull 330 lbs 150 kg Rated Performance (at rated pressure/volume) (1) Full Drum Line Speed 78 fpm 23.8 mpm Sound Pressure Level (dBA) (2, 3) 89 dBA...
- Page 10 Performance Graph 2.15 2.06 1st Layer 2.04 1.98 Half Drum 1.93 1.87 1.81 1.75 Full Drum 1.69 1.64 Half Drum 1.58 Full Drum 1st Layer 1.53 1.47 1.42 Line Speed (ft/min) 14.3 19.0 23.9 28.6 33.4 38.2 42.9 47.7 52.5 57.3 62.0 66.8...
-
Page 11: Installation
INSTALLATION Prior to installing winch, carefully inspect it for possible shipping Winch Bolt Hole Mounting Dimensions damage. Winch gearbox and disc brake are supplied fully lubricated from factory. Refer to “LUBRICATION” section on page 30 for recommended oils. Drum • Owners and users are advised to examine specific, local or other regulations, including American National Standards Institute and/or OSHA Regulations which may apply to a particular type of use of this product before installing or... - Page 12 Wire Rope Take-off Angles Sleeve Wire End Strands 75˚-90˚ 60˚-75˚ Core Strand 45˚-60˚ Arm configuration will vary depending on wire rope take off angle. Split Wedge (Dwg. MHP0166) Wrap wire rope with wire a distance from the end 2-5/8 in. (60.3 mm).
- Page 13 Never use wire rope as a sling. Connection of the Control Console to the Winch Always ensure wire rope is correctly spooled and the first layer is tight against the drum. To connect the supply hoses to the control console, unions are Always follow wire rope manufacturer’s recommendations placed so as to avoid any possible reversal during assembly.
-
Page 14: Air Supply
Clockwise clockwise to Adjust • The whole equipment is delivered with 16 ft (5 meters) of to Adjust hose. Do not modify the length without informing Ingersoll-Rand. BLUE Setscrew Setscrew Air Lines (Dwg. MHP0607) The inside diameter of the winch air supply lines must not be less than the size shown in Table 3 on page 14. -
Page 15: Initial Winch Operating Checks
connections, all air supply lines should be purged with clean, Initial Winch Operating Checks moisture free air or nitrogen before connecting to winch inlet. Supply lines should be as short and straight as installation Winches are tested for proper operation prior to leaving factory. conditions will permit. -
Page 16: System Schematic
SYSTEM SCHEMATIC (Dwg. MHP2353) MHD56244 - Edition 1... - Page 17 SEQUENCER SCHEMATIC (Dwg. MHP2365) MHD56244 - Edition 1...
-
Page 18: Operation
Lifting and lowering speeds are operator controlled and signals, and the lift chart information. should be as slow as practical. Ingersoll-Rand recommends that you do not exceed 100 ft (30 m) per minute. Any applicable codes and standards should be followed. -
Page 19: Winch Controls
Control Console Layout Lever Control Failure Balancing Standard Winch On Line Valve Indicator Mode Indicator Mode Indicator Indicator (424) (423) (422) (422) (422) Balancing Network Air Pressure Pressure Guage Guage (426) (425) Balancing Pressure Control Regulator (430) Emergency Lockout Selector Button Stop Switch... -
Page 20: Winch Brakes
When selecting a mode or even permanently, the control box Raise person 18 inch (0.5 meter) above floor with main monitors those functions which might be dangerous to the lifted control lever. person such as: Select balancing mode. Brake opening through the band detector. The connection distributor that switches the winch Green indicator will come on to indicate balancing mode working. -
Page 21: Slack Line Detector
adjusted to hold the required load. Refer to ‘Adjustments’ on page Emergency Lowering Precautions 31, in the “MAINTENANCE” section. If brake band cannot be adjusted to hold rated load, the brake must be disassembled, Emergency lowering operations must be performed by a inspected and repaired. -
Page 22: Inspection
INSPECTION Inspection information is based in part on American National WINCH. Prior to operation, visually inspect winch housings, Standards Institute Safety Codes (ASME B30.7). controls, brakes, side rails, uprights and drum for indications of damage. Do not operate unless the wire rope feeds onto the drum smoothly. -
Page 23: Periodic Inspection
BRAKES. Brakes must hold a 125% rated load at mid-drum Periodic Inspection without slipping. If indicated by poor operation or visible damage, disassemble and repair brake(s). Check all brake Winch periodic inspection intervals vary depending on the surfaces for wear, deformation or foreign deposits. Clean and conditions listed below: replace components as necessary. -
Page 24: Inspection And Maintenance Report
Refer to Parts, Operation and Maintenance Manual “INSPECTION” section for general inspection criteria. Also, refer to appropriate National Standards and codes of practice. If in doubt about an existing condition, contact the nearest Ingersoll-Rand Distributor or the factory for technical assistance. -
Page 25: Troubleshooting
TROUBLESHOOTING This section provides basic troubleshooting information. Determination of specific causes to problems are best identified by thorough inspections performed by personnel instructed in safety, operation and maintenance of this equipment. The chart below provides a brief guide to common winch symptoms, probable causes and remedies. SYMPTOM CAUSE REMEDY... - Page 26 If the level is high, use the interlock adjustment procedure, if the adjustment does not correct the problem exchange the command block, contact Ingersoll-Rand customer service. If the input 14 is at a low-level, check output 23, a high level is required.
- Page 27 SYMPTOM CAUSE REMEDY Point A at a high level: Check input 19, high level required. If the level is high, exchange the command block. If input 19 is at a low level, check the hose between input 19 and the emergency stop. Point B at a high level: Exchange the command block.
- Page 28 Standard Mode Failure (Dwg. MHP2367) Standard Mode Problems Without Failure Signal (Dwg. MHP2368) MHD56244 - Edition 1...
- Page 29 Floating Mode Failure: View One (Dwg. MHP2369) Floating Mode Failure: View Two (Dwg. MHP2370) MHD56244 - Edition 1...
- Page 30 Interlock Adjustment Procedure Test Point Interlock Adjustment Screw (Dwg. MHP2371) Disconnect input 14, close the hose coming from the winch; connect an adjustable regulator to the input. Supply air to the winch. Adjust the pressure to 44 psi (3 bar). Unscrew the nut on the interlock and then unscrew the screw until you have a low level on test point A.
-
Page 31: Lubrication
Approval for the use of other The reduction gear assembly is filled and shipped with oil from lubricants must be obtained from your Ingersoll-Rand distributor. the factory. Oil capacity is approximately 0.25 pt (0.12 ltr). Use Failure to observe this precaution may result in damage to winch only high quality lubricants in the reduction gear assembly. -
Page 32: Maintenance
MAINTENANCE Turn adjustment clevis (358) clockwise to increase cylinder rod extension. Turn clevis counterclockwise to decrease cylinder rod extension. • Never perform maintenance on the winch while it is Assemble clevis (358) to brake lever (355) using pin (357). supporting a load. Release air to brake cylinder (362). - Page 33 Immobilize the motor rotors with a bar between the teeth and Winch Disassembly remove nuts (131 and 136). Remove the drive gear (135), the idle gear (149), the retainer Refer to Dwg. MHP2376 on page 40 and MHP2375 on page 42. ring (146) and internal ring.
-
Page 34: Cleaning, Inspection And Repair
drum (60). Remove bushing (415) from end of spacer (416), remove Remove cotter pins (352) and pins (375) so brake band halves spacer and springs (409) and (411) from base. (384) can be removed from the arm (379). Lower winch From both ends of roller shaft (403), remove retainer ring when brake band assembly has been removed. -
Page 35: Assembly
Inspect all threaded items for: Immobilize the motor rotors with an bar between the teeth damaged threads. Replace if necessary. and install nuts (131 and 136) secured with Loctite® 243. Inspect drum band brake lining for: Install bearings (145 and 148), stops (147) and pins (138) in oil, grease and glazing. - Page 36 CAUTION • When installing the motor on reducer-brake, be careful not to damage the lip of the oil seal (105). Refer to Dwg. MHP2358 on page 44. Torque Limiter Assembly Refer to Dwg. MHP2386 on page 48. Install diaphragm (166), washer (167) and nut (172). Install spring (171), ‘O’...
-
Page 37: Testing
Install oil seal (454) in end cover with lip toward the bearing. Push spacer (416) through one of the holes in base (421), and 10. Apply a light coat of Loctite 515 to the mating surface of slide springs (409) and (411) onto spacer. ®... - Page 38 • Testing to more than 125% of rated line pull may be required to comply with standards and regulations set forth in areas outside the USA. Limit Switch Operate winch through three complete cycles to ensure consistent limit switch operation within +/- 2 ft (+/- 0.6 m) of setpoints. Refer to ‘Limit Switch’...
-
Page 39: Parts Drawings And Parts Lists Table Of Contents
PARTS DRAWINGS AND PARTS LISTS TABLE OF CONTENTS Description Page Drum, Base Assembly Drawing (MHP2376) ..............................40 Drum, Base Assembly Parts List ..................................41 Motor Assembly Drawing (MHP2357) and Parts List............................42 Disc Brake and Gear Assembly Drawing (MHP2358) and Parts List ......................44 Drum Brake Assembly Drawing (MHP2373)..............................46 Drum Brake Assembly Parts List ..................................47 Torque Limiter Assembly Drawing (MHP2386) and Parts List ........................48... -
Page 40: Service Notes
SERVICE NOTES MHD56244 - Edition 1... -
Page 41: Winch Parts Drawings And Parts Lists
DRUM AND BASE ASSEMBLY DRAWING (Dwg. MHP2376) MHD56244 - Edition 1... -
Page 42: Drum, Base Assembly Parts List
DRUM AND BASE ASSEMBLY PARTS LIST Item Description Qty. Part Item Description Qty. Part of Part Total Number of Part Total Number Capscrew 54133 Outboard Upright 28310 Capscrew 51766 Capscrew 50183 Inboard Upright 28300 Dowel Pin 52334 Motor Assembly 76157549 Nameplate 71106967-R Drum Carrier Assembly... -
Page 43: Motor Assembly Drawing (Mhp2357) And Parts List
MOTOR ASSEMBLY DRAWING AND PARTS LIST (Dwg. MHP2357) Item Description Qty. Part Item Description Qty. Part of Part Total Number of Part Total Number Motor Assembly Contact factory Lockwasher 4520-1006 Ball Bearing 50600004 Capscrew 41019001 Slotted Nut 57000004 Needle Bearing 56462813 •... - Page 44 SERVICE NOTES MHD56244 - Edition 1...
-
Page 45: Disc Brake And Gear Assembly Drawing (Mhp2358) And Parts List
DISC BRAKE AND REDUCTION GEAR ASSEMBLY DRAWING (Dwg. MHP2358) MHD56244 - Edition 1... - Page 46 DISC BRAKE AND REDUCTION GEAR ASSEMBLY PARTS LIST Item Description Qty. Part Item Description Qty. Part of Part Total Number of Part Total Number Ouput Ring Gear 96090094 Brake Piston 96180126 • 101 Ball Bearing 50800006 ‘O’ Ring 58235229 • 82 Oil Seal 58017530 Washer...
-
Page 47: Drum Brake Assembly Drawing (Mhp2373)
DRUM BRAKE ASSEMBLY DRAWING (Dwg. MHP2373) MHD56244 - Edition 1... -
Page 48: Drum Brake Assembly Parts List
DRUM BRAKE ASSEMBLY PARTS LIST Item Description Qty. Part Number of Part Total Capscrew 50973 Lockwasher 50181 Drum (8 in. [203 mm] long)† Contact factory Drum (12 in. [305 mm] long)† 11354-2 Drum (16 in. [406 mm] long)† Contact factory Drum (24 in. -
Page 49: Torque Limiter Assembly Drawing (Mhp2386) And Parts List
TORQUE LIMITER ASSEMBLY DRAWING AND PARTS LIST (Dwg. MHP2386) Item Description Qty. Part of Part Total Number Torque Limiter Assembly - - - 76360045 (Includes items 161 through 181) Capscrew 41327406 Cover 96360041 • 163 ‘O’ Ring 58222329 Screw 42007307 Valve 96360017 •... - Page 50 SERVICE NOTES MHD56244 - Edition 1...
-
Page 51: Slack Line Detector Assembly Drawing (Mhp2366)
SLACK LINE DETECTOR ASSEMBLY DRAWING (Dwg. MHP2366) MHD56244 - Edition 1... -
Page 52: Slack Line Detector Assembly Parts List
SLACK LINE DETECTOR ASSEMBLY PARTS LIST Item Description Qty. Part of Part Total Number Slack Line Detector Assembly 28281 (Incl’s items 21, 385, 460, 481, 482, and 501-523) Capscrew 50973 Washer 52914 Breather 51559 Limit Valve 71356430 Fitting, Plug 54292 Roller 8 in. -
Page 53: Press Roller Assembly Drawing (Mhp2268)
PRESS ROLLER ASSEMBLY DRAWING (Dwg. MHP2268) MHD56244 - Edition 1... -
Page 54: Press Roller Assembly Parts List
PRESS ROLLER ASSEMBLY PARTS LIST Item Description Qty. Part of Part Total Number Press Roller Assembly (Incl’s items 385 and 401-421) 71383780 Washer 52914 Press Roller, Short 71383764 Press Roller 8 in. (203 mm) long drum Contact factory Press Roller 12 in. (305 mm) long drum 71383772 Press Roller 16 in. -
Page 55: Limit Switch Assembly Drawing (Mhp2375)
LIMIT SWITCH ASSEMBLY DRAWING Hose Routing Limit Switch Air Motor Control Valve Rear (Dwg. MHP2375) MHD56244 - Edition 1... -
Page 56: Limit Switch Assembly Parts List
LIMIT SWITCH ASSEMBLY PARTS LIST Item Description Qty. Part of Part Total Number Limit Switch Assembly (Incl’s items 5, 13, 71-72, 74, 77, 452- 27306-1 469, 471-479, 481, and 482) Lockwasher 50200 Seal 51474 Bearing 51797 Retainer 19232 Capscrew 71030787 End Cover 19233 Capscrew... -
Page 57: Control Console View (Mhp2354) And Parts List
CONTROL CONSOLE VIEW AND PARTS LIST Lever Control Failure Balancing Standard Winch On Line Valve Indicator Mode Indicator Indicator Mode Indicator (424) (423) (422) (422) (422) Balancing Network Air Pressure Pressure Guage Guage (426) (425) Balancing Pressure Control Regulator (430) Emergency Lockout Selector... -
Page 58: Directional Control Valve Assembly Drawing (Mhp2361) And Parts List
DIRECTIONAL CONTROL VALVE ASSEMBLY DRAWING AND PARTS LIST (Dwg. MHP2361) Item Description Qty. Part of Part Total Number Directional Control Valve Assembly 68553441 (Refer to Dwg. MHP2362 on page 58) Cover 96150378 Capscrew 41326306 Capscrew 41322306 Lockwasher 45201006 Washer 45700005 •... -
Page 59: Lever Control Valve Assembly Drawing (Mhp2362) And Parts List
LEVER CONTROL VALVE ASSEMBLY DRAWING (Dwg. MHP2362) MHD56244 - Edition 1... - Page 60 LEVER CONTROL VALVE PARTS LIST Item Description Qty. Part of Part Total Number Fitting, Nipple 1/2-3/4 in 61331032 Female, Elbow 3/4 in 61331232 Fitting, 3/4 in 61645232 Fitting, Elbow 3/4 in 61330932 Elbow 1/8 in 68143628 Pipe 68045428 Directional Control Valve Assembly 68553441 Sleeve 61045128...
-
Page 61: Control Box And Sequencer View (Mhp2359)
CONTROL BOX AND SEQUENCER VIEWS (Dwg. MHP2359) MHD56244 - Edition 1... -
Page 62: Sequencer And Winch Assembly View (Mhp2360)
CONTROL BOX AND SEQUENCER PARTS LIST Item Description Qty. Part of Part Total Number Sequencer Assembly 76150490 Control Box Assembly 76150491 Connecting Flange 96150408 High Precision Pressure Regulator 67750141 Regulator 3/4 in 67730541 Servo Pressure Regulator 1/4 in 67730741 Pressure Regulator 1/4 in 67730841 Shut-Off Valve 3/4 in 76170123... -
Page 63: Connecting Flange Piping And Hoses Legend Drawing (Mhp2363)
CONNECTING FLANGE PIPING AND HOSES LEGEND (Dwg. MHP2363) MHD56244 - Edition 1... -
Page 64: Connecting Flange Piping And Hoses Legend Drawing (Mhp2355)
CONNECTING FLANGE PIPING AND HOSES LEGEND Muffler C = Hoses from the Control Console Viewed from beneath Control Box (Dwg. MHP2355) MHD56244 - Edition 1... -
Page 65: Connecting Flange Legend
CONNECTING FLANGE LEGEND VeA: Port A of Exhaust Valve Piloting Pressure FH: Top Limit Switch FB + S: Bottom Limit Switch + Slack DFR: Brake Detection M20-B20 ADFR: Brake Detection Supply L2a: Port A of Torque Limiter Control Valve Floating M22-R22 Dc: Signal to Directional Control Valve E Dc: Directional Control Valve Inlet... -
Page 66: Control Flange Legend
CONTROL FLANGE LEGEND PA: Inlet Pressure PP: Piloting Pressure PU: Working Pressure FLT: Floating Mode STD: Standard Mode VF: Floating Indicator VA: Failure Indicator DFR: Brake Detector FB: Bottom Limit Switch FH: Top Limit Switch UP: Lifting DW: Lowering OUTLET Ve, Dc: Exhaust Valve Outlet, Directional Valve Outlet INLET Ve: Exhaust Valve Inlet INLET Dc: Directional Valve Inlet RESET... -
Page 67: Drum Guard Assembly Drawing (Mhp2281) And Parts List
DRUM GUARD ASSEMBLY DRAWING AND PARTS LIST (Dwg. MHP2281) Item Description Qty. Part of Part Total Number Drum Guard Assembly* (8 in. [203 mm] long drum) Contact factory Drum Guard Assembly* (12 in. [305 mm] long drum) 11283-2 Drum Guard Assembly* (16 in. [406 mm] long drum) Contact factory Drum Guard Assembly* (24 in. -
Page 68: Winch Label/Tag Location Drawing (Mhp2270) And Parts List
Notice, Man Rider (Refer to Label on page 6) 71108856 Label, Throttle Direction 96180102 Label, Warning (Refer to Label on page 6) 71124887 Label, Overwind Cable 96180103 Label, Limit Switch 71149454 Label, Ingersoll-Rand Logo 71106256 Label, Product 71111793 Label Sheet 71295240 Label, Open Book 96180098 Label, CE 96180096... - Page 69 SERVICE NOTES MHD56244 - Edition 1...
- Page 70 SERVICE NOTES MHD56244 - Edition 1...
-
Page 71: Parts Ordering Information
PARTS ORDERING INFORMATION The use of other than Ingersoll-Rand replacement parts may Return Goods Policy adversely affect the safe operation and performance of this product. Ingersoll-Rand will not accept any returned goods for warranty For your convenience and future reference it is recommended that or service work unless prior arrangements have been made and the following information be recorded. -
Page 72: Limited Warranty
WARRANTY LIMITED WARRANTY Ingersoll-Rand Company (I-R) warrants to the original user its I-R makes no other warranty, and all implied warranties Products to be free of defects in material and workmanship for a including any warranty of merchantability or fitness for a period of one year from the date of purchase. - Page 73 Ingersoll-Rand Annandale, NJ world. Contact the nearest Production Equipment Group Technical Support P.O. Box 970 Ingersoll-Rand office for the 730 N.W. 107 Avenue 1467 Route 31 South name and address of the Suite 300, Miami, FL Ingersoll-Rand Annandale, NJ 08801...
Need help?
Do you have a question about the force 5 FA150KGMR-RC MAN RIDER and is the answer not in the manual?
Questions and answers