Related Manuals for Ingersoll-Rand FORCE 5i FH10i
Summary of Contents for Ingersoll-Rand FORCE 5i FH10i
- Page 1 Product Maintenance Information FORCE 5i Hydraulic Winch Model FH10i (Dwg. MHP3010) Save These Instructions Form MHD56421 Edition 2 October 2013 45895125 2013 Ingersoll-Rand ©...
-
Page 2: Periodic Inspection
Only allow trained technicians to perform maintenance on this product. For additional information contact factory or nearest Ingersoll Rand Ingersoll Rand Distributor. For additional supporting documentation refer to Table 1 ‘Product Information Manuals’ on page 2. Manuals can be downloaded from http://www.ingersollrandproducts.com. The use of other than genuine Ingersoll Rand replacement parts may result in safety hazards, decreased performance and increased maintenance and will invalidate all warranties. - Page 3 Table 3: Maintenance Interval Chart Normal Application The following work can be completed by owner maintenance personnel System Hydraulic Filter Inspect system filter every 45 days or 125 hours. Grease Fittings Lubricate grease fittings every 180 days or 500 hours. Gearbox Oil Level Check oil level in gearbox every 180 days or 500 hours.
-
Page 4: Inspection Report
INSPECTION REPORT Ingersoll Rand Force 5 Infinity Series Models FH10i Hydraulic Winches Model Number: Date: Serial Number: Inspected by: Reason for Inspection: (Check Applicable Box) 1. Scheduled Periodic Inspection: (_____ Months _____ Years) Operating Environment: Normal ____ Heavy ____ Severe ____ 2. -
Page 5: Troubleshooting
TROUBLESHOOTING This section provides basic troubleshooting information. Determination of specific causes to problems are best identified by thorough inspections performed by personnel instructed in safety, operation and maintenance of this equipment. The chart below provides a brief guide to common winch symptoms, probable causes and remedies. SYMPTOM CAUSE REMEDY... - Page 6 MAINTENANCE 5. Check brake band is partially lifted from drum diameter to reduce drag when WARNING brake is not in use. CAUTION • Never perform maintenance on the winch while it is supporting a load. • Before performing maintenance, tag controls: •...
- Page 7 27. Pull outboard upright (184) away from drum (96). 28. Remove bearing (188). n Disassembly 29. Position drum (96) vertically (with reduction gear assembly facing up). 30. Remove capscrews (63) holding adapter (52) onto drum. General Disassembly Instructions 31. Install two 1/2 inch - 13 NC x 2 inch capscrews into threaded holes in outer bolt pattern ring of adapter (52).
-
Page 8: Cleaning, Inspection And Repair
26. Remove capscrews (452) and separate front cover (450). Remove thrust plate (449) and gasket (447). n Assembly 27. Remove adjusting screw (453). General Assembly Instructions Motor Disassembly Use all new gaskets and seals. • Refer to motor manufacturer’s literature for motor maintenance instructions. It is •... - Page 9 1. Install new bushing (311) in winch upright (184) if replacement was required. NOTICE 2. Install shaft (304) in handle (301) and secure with nut (303) and capscrew (302). 3. Install cover (307) on shaft (304) so capscrew holes are aligned with holes in upright when handle (301) is in a horizontal position.
-
Page 10: Torque Chart
TORQUE CHART Standard Coarse Thread Torque SAE Grade 5 SAE Grade 8 Size Lubricated PTFE Lubricated PTFE 1/4-20 8-10 12-14 9-10 5/16-18 17-20 13-15 25-28 18-21 11-13 3/8-16 31-35 23-26 14-16 44-49 33-37 20-22 7/16-14 49-56 37-42 22-25 70-79 52-59 31-36 1/2-13 75-85... -
Page 11: Service Notes
SERVICE NOTES Form MHD56421 Edition 2... - Page 12 www.ingersollrandproducts.com...
Need help?
Do you have a question about the FORCE 5i FH10i and is the answer not in the manual?
Questions and answers